IEC 60390A:1976
(Main)First supplement - Dimensions of spindle ends for manually operated electronic components
First supplement - Dimensions of spindle ends for manually operated electronic components
Contains dimensions and tolerances for spindle ends made to original inch dimensions. The contents of the corrigendum of September 1979 have been included in this copy.
Premier complément - Dimensions des terminaisons des axes de composants électroniques pour commande manuelle
Contient des dimensions et des tolérances pour terminaisons des axes réalisés selon les dimensions originales en inches. Le contenu du corrigendum de Septembre 1979 a été pris en considération dans cet exemplaire.
General Information
Standards Content (Sample)
Publication 390A de la C E I
I E C Publication 390A
Premier complément à la Publication 390 (1972)
First supplement to Publication 390 (1972)
Dimensions des
terminaisons des axes de Dimensions of spindle ends for
composants électroniques
pour commande manuelle manually operated electronic components
...
This May Also Interest You
IEC 61851-24:2023, together with IEC 61851-23, applies to digital communication between a DC EV supply equipment and an electric road vehicle (EV) for control of conductive DC power transfer, with a rated supply voltage up to 1 000 V AC or up to 1 500 V DC and a rated output voltage up to 1 500 V DC.
This document also applies to digital communication between the DC EV charging/discharging station and the EV for system A, as specified in Annex A.
The EV charging mode is mode 4, according to IEC 61851-23.
Annex A, Annex B, and Annex C give descriptions of digital communications for control of DC charging specific to DC EV charging systems A, B and C as defined in IEC 61851-23.
This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
- Annex A and Annex B have been updated in line with IEC 61851-23:2023 and relevant standards.
- Standard105 pagesEnglish and French languagesale 15% off
IEC 61851-23:2023 applies to the EV supply equipment to provide energy transfer between the supply network and electric vehicles (EVs), with a rated maximum voltage at side A of up to 1 000 V AC or up to 1 500 V DC and a rated maximum voltage at side B up to 1 500 V DC.
This document specifies the EV supply equipment of system A, system B and system C as defined in Annex AA, Annex BB and Annex CC. Other systems are under consideration.
This document provides the requirements for bidirectional power transfer (BPT) EV supply equipment for system A, with a rated maximum voltage at side A up to 1 000 V AC or 1 500 V DC. The requirements for reverse power transfer (RPT) and BPT for system B and system C are under consideration and are not specified in this document.
This second edition cancels and replaces the first edition published in 2014. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) the structure has been rearranged according to IEC 61851-1:2017;
b) electrical safety requirements in Clause 8 and Clause 12 have been revised based on the requirements in IEC 62477-1 and inspired by the hazard based safety approach of IEC 62368-1;
c) test methods for checking conformity to the stated requirements have been mostly added; general provisions for compliance tests have been specified in Clause 102;
d) specific requirements and/or information for the following functions have been added: energy transfer with thermal management system (101.2), bi-directional power transfer control (Annex DD), multi- side B separated EV supply equipment (Annex FF), and communication and energy transfer process (Annex GG);
e) Annex AA (system A), Annex BB (system B) and Annex CC (system C) have been updated including additions in conjunction with b) and c). This document has been limited to be applicable to system A, system B and system C;
f) the former Annex DD and Annex EE have been deleted. A new Annex EE, with the requirements for the artificial test load, has been added.
g) a new informative annex for the touch current and the touch impulse current (Annex HH) has been added
- Standard383 pagesEnglish languagesale 15% off
IEC 61969-3:2023 is available as IEC 61969-3:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61969-3:2023 specifies a set of basic environmental requirements and tests, as well as safety aspects for outdoor enclosures for electrical and electronic equipment, under conditions of non-weatherprotected locations above ground. The purpose of this document is to define a minimum level of environmental performance in order to meet requirements of storage, transport and final installation. The intention is to establish basic environmental performance criteria for outdoor enclosure compliance.
- Standard54 pagesEnglish languagesale 15% off
- Standard33 pagesEnglish and French languagesale 15% off
IEC 63098-4:2023 provides the performance standards of the RoF-based 5G indoor distributed antenna system (DAS) network for cost-effectively offering quality of service (QoS) guaranteed 5G mobile communication services with high bandwidth and low-latency characteristics without radio shadowing in an indoor environment. First of all, the system overview, system configurations, and the elements of the system are presented and then the electrical and optical interfaces for each system element are defined. Finally, the detail system performance specifications of each element are described for downlink and uplink configurations.
- Standard17 pagesEnglish languagesale 15% off
IEC 61969-1:2023 is available as IEC 61969-1:2023 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.IEC 61969-1:2023 contains design guidelines for outdoor enclosures for electrical and electronic equipment and is applicable over a wide field of mechanical, electromechanical and electronic equipment and its installation where a modular design is used. The objectives of this document are:
- to provide an overview of specifications for enclosures focused on requirements for outdoor applications for stationary use at non-weatherprotected locations, and
- to achieve product integrity under outdoor conditions and to ease product selection for the sourcing of outdoor enclosures from different vendors.
- Standard40 pagesEnglish languagesale 15% off
- Standard25 pagesEnglish and French languagesale 15% off
IEC 60297-3-1:2023 provides information on the technological schemes of the IEC 60297 series and shows how to apply the 19-inch series standards for the mechanical structure practices for electrical and electronic equipment.
- Technical report34 pagesEnglish languagesale 15% off
IEC 60286-3:2022 is applicable to the tape packaging of electronic components without leads or with lead stumps, intended to be connected to electronic circuits. It includes only those dimensions that are essential for the taping of components intended for the above-mentioned purposes. This document also includes requirements related to the packaging of singulated die products including bare die and bumped die (flip chips). This edition includes the following significant technical changes with respect to the previous edition:
addition terms and definitions.
addition of a table of the classification to symbols concerning drive hole diameter and distance between the reel hole centre and the drive hole centre;
addition of drive hole to the reel (optional);
revision of reel hole diameter tolerances;
revision of 72 mm tape size carrier tape width dimension tolerances;
addition of Annex B (informative);
addition of component size 0201M.
- Standard170 pagesEnglish languagesale 15% off
- Standard113 pagesEnglish and French languagesale 15% off
IEC 60286-2:2022 applies to the tape packaging of components with two or more unidirectional leads for use in electronic equipment. It provides dimensions and tolerances necessary to tape components with unidirectional leads. In general, the tape is applied to the component leads.
It covers requirements for taping techniques used with equipment for automatic handling, pre-forming of leads, insertion and other operations and includes only those dimensions which are essential to the taping of components intended for the above-mentioned purposes.
This edition includes the following significant technical changes with respect to the previous edition:
a) complete revision of structure;
b) consolidation of essential parameters and requirements in Clause 4.
- Standard70 pagesEnglish and French languagesale 15% off
- Technical report2 pagesEnglish languagesale 15% off
IEC 61587-1:2022 specifies environmental requirements, test set-ups, as well as safety aspects for empty enclosures, i.e. cabinets, racks, subracks, chassis, chassis integrated subracks and associated plug-in units under indoor condition use and transportation. It defines classifications (product performance levels) for these products, regarding and simulating the usually arising loads during their use. For mechanical static and dynamic load tests typical examples with dummy loads are used.
The purpose of this document is to establish defined levels of physical performance in order to meet certain requirements of manufacture, storage, transport and final location conditions.
This document applies in general only to the above cited mechanical structures.
This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) Modification of title.
b) Revision of Clauses 6, 7 and 8 including new defined test setups.
c) Compatibility with IEC 61587-2, IEC 61587-3 and IEC 61587-5.
- Standard91 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.