IEC 61000-4-11:2020
(Main)Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with input current up to 16 A per phase
Electromagnetic compatibility (EMC) - Part 4-11: Testing and measurement techniques - Voltage dips, short interruptions and voltage variations immunity tests for equipment with input current up to 16 A per phase
IEC 61000-4-11:2020 is available as IEC 61000-4-11:2020 RLV which contains the International Standard and its Redline version, showing all changes of the technical content compared to the previous edition.
IEC 61000-4-11:2020 defines the immunity test methods and range of preferred test levels for electrical and electronic equipment connected to low-voltage power supply networks for voltage dips, short interruptions, and voltage variations. This document applies to electrical and electronic equipment having a rated input current not exceeding 16 A per phase, for connection to 50 Hz or 60 Hz AC networks. It does not apply to electrical and electronic equipment for connection to 400 Hz AC networks. Tests for these networks will be covered by future IEC documents. The object of this document is to establish a common reference for evaluating the immunity of electrical and electronic equipment when subjected to voltage dips, short interruptions and voltage variations.
NOTE 1 Voltage fluctuation immunity tests are covered by IEC 61000-4-14. The test method documented in this document describes a consistent method to assess the immunity of equipment or a system against a defined phenomenon.
NOTE 2 As described in IEC Guide 107, this is a basic EMC publication for use by product committees of the IEC. As also stated in Guide 107, the IEC product committees are responsible for determining whether this immunity test standard should be applied or not, and, if applied, they are responsible for defining the appropriate test levels. Technical committee 77 and its sub-committees are prepared to co-operate with product committees in the evaluation of the value of particular immunity tests for their products. This third edition cancels and replaces the second edition published in 2004 and Amendment 1:2017. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- rise time and fall time of transients are now defined terms in Clause 3;
- the origin of voltage dips and short interruptions is now stated in Clause 4.
The contents of the corrigendum of May 2020 and October 2022 have been included in this copy.
Compatibilité électromagnétique (CEM) - Partie 4-11: Techniques d'essai et de mesure - Essais d'immunité aux creux de tension, coupures brèves et variations de tension pour les appareils à courant d’entrée inférieur ou égal à 16 A par phase
IEC 61000-4-11:2020 est disponible sous forme de IEC 61000-4-11:2020 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 61000-4-11:2020 définit les méthodes d'essai d'immunité ainsi que la plage des niveaux d'essais préférentiels pour les matériels électriques et électroniques connectés à des réseaux d'alimentation à basse tension pour les creux de tension, les coupures brèves et les variations de tension. Le présent document s’applique aux matériels électriques et électroniques dont le courant assigné d’entrée ne dépasse pas 16 A par phase et destinés à être reliés à des réseaux électriques à courant alternatif de 50 Hz ou 60 Hz. Il ne s'applique pas aux matériels électriques et électroniques destinés à être reliés à des réseaux électriques à courant alternatif de 400 Hz. Les essais pour ces réseaux seront traités dans des documents IEC à venir. Le but du présent document est d'établir une référence commune pour l'évaluation de l'immunité des matériels électriques et électroniques soumis à des creux de tension, à des coupures brèves et à des variations de tension.
NOTE 1 Les essais d’immunité aux fluctuations de tension sont traités dans l’IEC 61000-4-14. La méthode d’essai décrite dans le présent document détaille une méthode sans faille pour évaluer l’immunité d’un matériel ou d’un système à un phénomène prédéfini.
NOTE 2 Comme cela est décrit dans le Guide 107 de l’IEC, ce document est une publication fondamentale en CEM destinée à l’usage des comités de produits de l’IEC. Comme cela est également mentionné dans le Guide 107, les comités de produits de l’IEC sont chargés de décider s’il convient d’utiliser ou non cette norme d’essai d’immunité et, si elle est utilisée, les comités sont responsables de la définition des niveaux d’essai appropriés. Le comité d’études 77 et ses sous-comités sont prêts à coopérer avec les comités de produits pour l’évaluation de la pertinence des essais particuliers d’immunité pour leurs produits. Cette troisième édition annule et remplace la deuxième édition parue en 2004 et l'Amendement 1:2017. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- le temps de montée et le temps de descente sont désormais des termes définis à l’Article 3;
- l’origine des creux de tension et des coupures brèves est désormais décrite à l’Article 4.
Mots-clés : méthodes d'essai d'immunité, réseaux d'alimentation à basse tension
Le contenu du corrigendum de mai 2020 et d'octobre 2022 a été introduit dans cet exemplaire.
General Information
Relations
Buy Standard
Standards Content (Sample)
IEC 61000-4-11 ®
Edition 3.0 2020-01
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
BASIC EMC PUBLICATION
Electromagnetic compatibility (EMC) –
Part 4-11: Testing and measurement techniques – Voltage dips, short
interruptions and voltage variations immunity tests for equipment with input
current up to 16 A per phase
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and 67 000 electrotechnical terminology entries in English and
once a month by email. French extracted from the Terms and Definitions clause of
IEC publications issued since 2002. Some entries have been
IEC Customer Service Centre - webstore.iec.ch/csc collected from earlier publications of IEC TC 37, 77, 86 and
If you wish to give us your feedback on this publication or CISPR.
need further assistance, please contact the Customer Service
Centre: sales@iec.ch.
IEC 61000-4-11 ®
Edition 3.0 2020-01
REDLINE VERSION
INTERNATIONAL
STANDARD
colour
inside
BASIC EMC PUBLICATION
Electromagnetic compatibility (EMC) –
Part 4-11: Testing and measurement techniques – Voltage dips, short
interruptions and voltage variations immunity tests for equipment with input
current up to 16 A per phase
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.100.20 ISBN 978-2-8322-7832-1
– 2 – IEC 61000-4-11:2020 RLV © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 2
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 General . 9
5 Test levels . 9
5.1 General . 9
5.2 Voltage dips and short interruptions . 10
5.3 Voltage variations. 11
6 Test instrumentation . 12
6.1 Test generator . 17
6.1.1 General . 17
6.1.2 Characteristics and performance of the generator . 17
6.1.3 Verification of the characteristics of the voltage dips, short interruptions
generators . 18
6.2 Power source . 19
7 Test set-up . 19
8 Test procedures . 19
8.1 General . 19
8.2 Laboratory reference conditions . 20
8.2.1 Climatic conditions . 20
8.2.2 Electromagnetic conditions . 20
8.3 Execution of the test . 20
8.3.1 General . 20
8.3.2 Voltage dips and short interruptions . 20
8.3.3 Voltage variations (optional) . 21
9 Evaluation of test results . 21
10 Test report . 22
Annex A (normative) Test circuit details . 23
A.1 Test generator peak inrush current drive capability . 23
A.2 Current monitor's characteristics for measuring peak inrush current
capability . 23
A.3 EUT peak inrush current requirement . 23
Annex B (informative) Electromagnetic environment classes . 25
Annex C (informative) Test instrumentation. 26
Annex D (informative) Rationale for generator specification regarding voltage, rise-
time and fall-time, and inrush current capability . 29
D.1 Concept of basic standard . 29
D.2 IEC 61000-4-11:1994 (first edition) . 29
D.3 Rationale for the need of rapid fall-times . 29
D.4 Interpretation of the rise-time and fall-time requirements during EUT testing . 30
D.5 Main conclusions . 30
D.6 Rationale for inrush current capability . 30
Bibliography . 32
Figure 1 – Voltage dip - Examples . 13
Figure 2 – Short interruption . 14
Figure 3 – Detailed view of rise and fall time . 15
Figure 4 – Voltage variation . 16
Figure 5 – Phase-to-neutral and phase-to-phase testing on three-phase systems . 21
Figure A.1 – Circuit for determining the inrush current drive capability of the short
interruptions generator . 24
Figure A.2 – Circuit for determining the peak inrush current requirement of an EUT . 24
Figure C.1 – Schematics of test instrumentation for voltage dips, short interruptions
and voltage variations . 27
Figure C.2 – Schematic of test instrumentation for three-phase voltage dips, short
interruptions and voltage variations using a power amplifier . 28
Table 1 – Preferred test levels and durations for voltage dips . 11
Table 2 – Preferred test levels and durations for short interruptions . 11
Table 3 – Timing of short-term supply voltage variations . 11
Table 4 – Generator specifications . 17
– 4 – IEC 61000-4-11:2020 RLV © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTROMAGNETIC COMPATIBILITY (EMC) –
Part 4-11: Testing and measurement techniques –
Voltage dips, short interruptions and voltage variations immunity
tests for equipment with input current up to 16 A per phase
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
This redline version of the official IEC Standard allows the user to identify the changes
made to the previous edition. A vertical bar appears in the margin wherever a change has
been made. Additions are in green text, deletions are in strikethrough red text.
---------------
...
IEC 61000-4-11 ®
Edition 3.0 2020-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
BASIC EMC PUBLICATION
PUBLICATION FONDAMENTALE EN CEM
Electromagnetic compatibility (EMC) –
Part 4-11: Testing and measurement techniques – Voltage dips, short
interruptions and voltage variations immunity tests for equipment with input
current up to 16 A per phase
Compatibilité électromagnétique (CEM) –
Partie 4-11: Techniques d'essai et de mesure – Essais d'immunité aux creux
de tension, coupures brèves et variations de tension pour les appareils
à courant d’entrée inférieur ou égal à 16 A par phase
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.
Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et
les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.
IEC Central Office Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.
IEC publications search - webstore.iec.ch/advsearchform Electropedia - www.electropedia.org
The advanced search enables to find IEC publications by a The world's leading online dictionary on electrotechnology,
variety of criteria (reference number, text, technical containing more than 22 000 terminological entries in English
committee,…). It also gives information on projects, replaced and French, with equivalent terms in 16 additional languages.
and withdrawn publications. Also known as the International Electrotechnical Vocabulary
(IEV) online.
IEC Just Published - webstore.iec.ch/justpublished
Stay up to date on all new IEC publications. Just Published IEC Glossary - std.iec.ch/glossary
details all new publications released. Available online and once 67 000 electrotechnical terminology entries in English and
a month by email. French extracted from the Terms and definitions clause of IEC
publications issued between 2002 and 2015. Some entries
IEC Customer Service Centre - webstore.iec.ch/csc have been collected from earlier publications of IEC TC 37, 77,
If you wish to give us your feedback on this publication or need 86 and CISPR.
further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.
A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.
Recherche de publications IEC - Le premier dictionnaire d'électrotechnologie en ligne au monde,
webstore.iec.ch/advsearchform avec plus de 22 000 articles terminologiques en anglais et en
La recherche avancée permet de trouver des publications IEC français, ainsi que les termes équivalents dans 16 langues
en utilisant différents critères (numéro de référence, texte, additionnelles. Egalement appelé Vocabulaire
comité d’études,…). Elle donne aussi des informations sur les Electrotechnique International (IEV) en ligne.
projets et les publications remplacées ou retirées.
Glossaire IEC - std.iec.ch/glossary
IEC Just Published - webstore.iec.ch/justpublished 67 000 entrées terminologiques électrotechniques, en anglais
Restez informé sur les nouvelles publications IEC. Just et en français, extraites des articles Termes et définitions des
Published détaille les nouvelles publications parues. publications IEC parues entre 2002 et 2015. Plus certaines
Disponible en ligne et une fois par mois par email. entrées antérieures extraites des publications des CE 37, 77,
86 et CISPR de l'IEC.
Service Clients - webstore.iec.ch/csc
Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
Electropedia - www.electropedia.org
IEC 61000-4-11 ®
Edition 3.0 2020-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
BASIC EMC PUBLICATION
PUBLICATION FONDAMENTALE EN CEM
Electromagnetic compatibility (EMC) –
Part 4-11: Testing and measurement techniques – Voltage dips, short
interruptions and voltage variations immunity tests for equipment with input
current up to 16 A per phase
Compatibilité électromagnétique (CEM) –
Partie 4-11: Techniques d'essai et de mesure – Essais d'immunité aux creux
de tension, coupures brèves et variations de tension pour les appareils
à courant d’entrée inférieur ou égal à 16 A par phase
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.100.20 ISBN 978-2-8322-7546-7
– 2 – IEC 61000-4-11:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 General . 9
5 Test levels . 9
5.1 General . 9
5.2 Voltage dips and short interruptions . 9
5.3 Voltage variations . 11
6 Test instrumentation . 14
6.1 Test generator . 14
6.1.1 General. 14
6.1.2 Characteristics and performance of the generator . 15
6.1.3 Verification of the characteristics of the voltage dips, short
interruptions generators . 15
6.2 Power source . 16
7 Test set-up . 16
8 Test procedures . 17
8.1 General . 17
8.2 Laboratory reference conditions . 17
8.2.1 Climatic conditions . 17
8.2.2 Electromagnetic conditions . 18
8.3 Execution of the test . 18
8.3.1 General. 18
8.3.2 Voltage dips and short interruptions . 18
8.3.3 Voltage variations . 19
9 Evaluation of test results . 19
10 Test report . 20
Annex A (normative) Test circuit details . 21
A.1 Test generator peak inrush current drive capability . 21
A.2 Current monitor's characteristics for measuring peak inrush current
capability . 21
A.3 EUT peak inrush current requirement . 21
Annex B (informative) Electromagnetic environment classes . 23
Annex C (informative) Test instrumentation. 24
Annex D (informative) Rationale for generator specification regarding voltage, rise-
time and fall-time, and inrush current capability . 27
D.1 Concept of basic standard . 27
D.2 IEC 61000-4-11:1994 (first edition) . 27
D.3 Rationale for the need of rapid fall-times . 27
D.4 Interpretation of the rise-time and fall-time requirements during EUT testing . 28
D.5 Main conclusions . 28
D.6 Rationale for inrush current capability . 28
Bibliography . 30
Figure 1 – Voltage dip – Examples . 12
Figure 2 – Short interruption . 13
Figure 3 – Detailed view of rise and fall time . 13
Figure 4 – Voltage variation . 14
Figure 5 – Phase-to-neutral and phase-to-phase testing on three-phase systems . 19
Figure A.1 – Circuit for determining the inrush current drive capability of the short
interruptions generator . 22
Figure A.2 – Circuit for determining the peak inrush current requirement of an EUT . 22
Figure C.1 – Schematics of test instrumentation for voltage dips, short interruptions
and voltage variations . 25
Figure C.2 – Schematic of test instrumentation for three-phase voltage dips, short
interruptions and voltage variations using a power amplifier . 26
Table 1 – Preferred test levels and durations for voltage dips . 10
Table 2 – Preferred test levels and durations for short interruptions . 11
Table 3 – Timing of short-term supply voltage variations . 11
Table 4 – Generator specifications . 15
– 4 – IEC 61000-4-11:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTROMAGNETIC COMPATIBILITY (EMC) –
Part 4-11: Testing and measurement techniques –
Voltage dips, short interruptions and voltage variations immunity
tests for equipment with input current up to 16 A per phase
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other acti
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.