ETSI EN 300 220-2 V3.1.1 (2017-02)

ETSI EN 300 220-2 V3.1.1 (2017-02)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) operating
in the frequency range 25 MHz to 1 000 MHz;
Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of Directive 2014/53/EU
for non specific radio equipment

---------------------- Page: 1 ----------------------
2 ETSI EN 300 220-2 V3.1.1 (2017-02)



Reference
REN/ERM-TG28-534
Keywords
harmonised standard, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 220-2 V3.1.1 (2017-02)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 All equipment conformance requirements . 10
4.2.0 Compliance . 10
4.2.1 Operating frequency . 10
4.2.1.0 Applicability. 10
4.2.1.1 Description . 10
4.2.1.2 Limits . 10
4.2.1.3 Conformance . 10
4.2.2 Unwanted emissions in the spurious domain . 11
4.2.2.0 Applicability. 11
4.2.2.1 Description . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.3 Transmitters conformance requirements . 11
4.3.1 Effective Radiated Power . 11
4.3.1.0 Applicability. 11
4.3.1.1 Description . 11
4.3.1.2 Limits . 11
4.3.1.3 Conformance . 11
4.3.2 Maximum e.r.p. spectral density . 11
4.3.2.0 Applicability. 11
4.3.2.1 Description . 11
4.3.2.2 Limits . 12
4.3.2.3 Conformance . 12
4.3.3 Duty Cycle . 12
4.3.3.0 Applicability. 12
4.3.3.1 Description . 12
4.3.3.2 Limits . 12
4.3.3.3 Conformance . 12
4.3.4 Occupied Bandwidth. 12
4.3.4.0 Applicability. 12
4.3.4.1 Description . 12
4.3.4.2 Limits . 12
4.3.4.3 Conformance . 12
4.3.5 Tx Out of Band Emissions . 12
4.3.5.0 Applicability. 12
4.3.5.1 Description . 13
4.3.5.2 Limits . 13
4.3.5.3 Conformance . 13
4.3.6 Transient power . 13
4.3.6.0 Applicability. 13
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 220-2 V3.1.1 (2017-02)
4.3.6.1 Description . 13
4.3.6.2 Limits . 13
4.3.6.3 Conformance . 13
4.3.7 Adjacent Channel Power . 13
4.3.7.0 Applicability. 13
4.3.7.1 Description . 13
4.3.7.2 Limits . 13
4.3.7.3 Conformance . 13
4.3.8 TX behaviour under Low Voltage Conditions . 14
4.3.8.0 Applicability. 14
4.3.8.1 Description . 14
4.3.8.2 Limits . 14
4.3.8.3 Conformance . 14
4.3.9 Adaptive Power Control . 14
4.3.9.0 Applicability. 14
4.3.9.1 Description . 14
4.3.9.2 Limits . 14
4.3.9.3 Conformance . 14
4.3.10 FHSS equipment . 14
4.3.10.0 Applicability. 14
4.3.10.1 Description . 14
4.3.10.2 Limits . 14
4.3.10.3 Conformance . 15
4.3.11 Short term behaviour . 15
4.3.11.0 Applicability. 15
4.3.11.1 Description . 15
4.3.11.2 Limits . 15
4.3.11.3 Conformance . 15
4.4 Receivers conformance requirements . 16
4.4.1 RX sensitivity . 16
4.4.1.0 Applicability. 16
4.4.1.1 Description . 16
4.4.1.2 Limits . 16
4.4.1.3 Conformance . 16
4.4.2 Blocking . 16
4.4.2.0 Applicability. 16
4.4.2.1 Description . 16
4.4.2.2 Limits . 16
4.4.2.3 Conformance . 16
4.5 Polite spectrum access conformance requirement . 16
4.5.1 Description . 16
4.5.2 Clear Channel Assessment threshold . 17
4.5.2.0 Applicability. 17
4.5.2.1 Description . 17
4.5.2.2 Limits . 17
4.5.2.3 Conformance . 17
4.5.3 Polite spectrum access timing parameters . 17
4.5.3.1 Applicability. 17
4.5.3.2 Limits . 17
4.5.3.3 Conformance . 17
4.5.4 Adaptive Frequency Agility . 17
4.5.4.0 Applicability. 17
4.5.4.1 Description . 17
4.5.4.2 Limits . 17
4.5.4.3 Conformance . 17
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 18
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to
1 000 MHz . 20
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 220-2 V3.1.1 (2017-02)
Annex C (normative): National Radio Interfaces not EU wide harmonised . 23
Annex D (informative): Application form for testing . 28
D.1 Introduction . 28
D.2 Information to declare according to ETSI EN 300 220-2 . 28
Annex E (informative): Selection of technical parameters . 30
E.1 Introduction . 30
E.2 Receiver parameters . 30
Annex F (informative): Bibliography . 31
Annex G (informative): Change History . 32
History . 33

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 300 220-2 V3.1.1 (2017-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
For non EU countries the present document may be used for regulatory (Type Approval) purposes.

National transposition dates
Date of adoption of this EN: 27 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 300 220-2 V3.1.1 (2017-02)
Introduction
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) operating in the
frequency range 25 MHz to 1 000 MHz. Full details of the entire series can be found in part 1 [1].
The present document is structured as follows:
Clause 2 provides references.
Clause 3 provides definitions of terms and abbreviations used.
Clause 4 provides technical requirements.
Annex A (informative) provides a relationship between the present document and essential requirements of
Directive 2014/53/EU [i.2].
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to 1 000 MHz.
Annex C (normative): National Radio Interfaces not EU wide harmonised.
Annex D (informative): Application form for testing.
Annex E (informative): Selection of parameters.
Annex F (informative): Bibliography.
Annex G (informative): Change History.
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 300 220-2 V3.1.1 (2017-02)
1 Scope
The present document specifies technical characteristics and methods of measurements for Non-specific Short Range
Devices category equipment types.
Non specific SRDs category is defined by the EU Commission Decision 2013/752/EU [i.3] as:
"The non-specific short-range device category covers all kinds of radio devices, regardless of the application or the
purpose, which fulfil the technical conditions as specified for a given frequency band. Typical uses include telemetry,
telecommand, alarms, data transmissions in general and other applications".
The present document covers equipment intended for fixed, mobile or nomadic use, including:
• stand-alone radio equipment;
• plug-in radio devices intended for use with or within a variety of host systems;
• plug-in radio devices intended for use within combined equipment.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: SRDs frequency ranges
Short Range Devices frequency ranges
Transmit and receive 26,957 MHz to 27,283 MHz
Transmit and receive 40,660 MHz to 40,700 MHz
Transmit and receive 138,2 MHz to 138,45 MHz
Transmit and receive 169,4 MHz to 169,8125 MHz
Transmit and receive 433,040 MHz to 434,790 MHz
Transmit and receive 863 MHz to 876 MHz
Transmit and receive 915 MHz to 921 MHz
NOTE: It should be noted that not all frequency bands in table 1 are implemented in all European
countries. Annex B provides an overview of radio interfaces which are harmonised in the
European Union. Annex C provides an overview of national radio interfaces not harmonised in
the European Union.

It is noted that in the European Commission Decision on Short Range Devices [i.3], some harmonised frequency bands
may be subject to usage restrictions such as the exclusion of video or audio use.
Equipment transmitting voice with analog modulation are excluded from the present document.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 300 220-2 V3.1.1 (2017-02)
[1] ETSI EN 300 220-1 (V3.1.1) (02-2017): "Short Range Devices (SRD) operating in the frequency
range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] CEPT/ERC/REC 70-03: "Relating to the use of Short Range Devices (SRD)".
NOTE: Avail
...

Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) operating
in the frequency range 25 MHz to 1 000 MHz;
Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of Directive 2014/53/EU
for non specific radio equipment

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)



Reference
REN/ERM-TG28-534
Keywords
harmonised standard, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 All equipment conformance requirements . 10
4.2.0 Compliance . 10
4.2.1 Operating frequency . 10
4.2.1.0 Applicability. 10
4.2.1.1 Description . 10
4.2.1.2 Limits . 10
4.2.1.3 Conformance . 10
4.2.2 Unwanted emissions in the spurious domain . 11
4.2.2.0 Applicability. 11
4.2.2.1 Description . 11
4.2.2.2 Limits . 11
4.2.2.3 Conformance . 11
4.3 Transmitters conformance requirements . 11
4.3.1 Effective Radiated Power . 11
4.3.1.0 Applicability. 11
4.3.1.1 Description . 11
4.3.1.2 Limits . 11
4.3.1.3 Conformance . 11
4.3.2 Maximum e.r.p spectral density . 11
4.3.2.0 Applicability. 11
4.3.2.1 Description . 11
4.3.2.2 Limits . 12
4.3.2.3 Conformance . 12
4.3.3 Duty Cycle . 12
4.3.3.0 Applicability. 12
4.3.3.1 Description . 12
4.3.3.2 Limits . 12
4.3.3.3 Conformance . 12
4.3.4 Occupied Bandwidth. 12
4.3.4.0 Applicability. 12
4.3.4.1 Description . 12
4.3.4.2 Limits . 12
4.3.4.3 Conformance . 12
4.3.5 Tx Out of Band Emissions . 12
4.3.5.0 Applicability. 12
4.3.5.1 Description . 13
4.3.5.2 Limits . 13
4.3.5.3 Conformance . 13
4.3.6 Transient power . 13
4.3.6.0 Applicability. 13
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)
4.3.6.1 Description . 13
4.3.6.2 Limits . 13
4.3.6.3 Conformance . 13
4.3.7 Adjacent Channel Power . 13
4.3.7.0 Applicability. 13
4.3.7.1 Description . 13
4.3.7.2 Limits . 13
4.3.7.3 Conformance . 13
4.3.8 TX behaviour under Low Voltage Conditions . 14
4.3.8.0 Applicability. 14
4.3.8.1 Description . 14
4.3.8.2 Limits . 14
4.3.8.3 Conformance . 14
4.3.9 Adaptive Power Control . 14
4.3.9.0 Applicability. 14
4.3.9.1 Description . 14
4.3.9.2 Limits . 14
4.3.9.3 Conformance . 14
4.3.10 FHSS equipment . 14
4.3.10.0 Applicability. 14
4.3.10.1 Description . 14
4.3.10.2 Limits . 14
4.3.10.3 Conformance . 15
4.3.11 Short term behaviour . 15
4.3.11.0 Applicability. 15
4.3.11.1 Description . 15
4.3.11.2 Limits . 15
4.3.11.3 Conformance . 16
4.4 Receivers conformance requirements . 16
4.4.1 RX sensitivity . 16
4.4.1.0 Applicability. 16
4.4.1.1 Description . 16
4.4.1.2 Limits . 16
4.4.1.3 Conformance . 16
4.4.2 Blocking . 16
4.4.2.0 Applicability. 16
4.4.2.1 Description . 16
4.4.2.2 Limits . 16
4.4.2.3 Conformance . 16
4.5 Polite spectrum access conformance requirement . 16
4.5.1 Description . 16
4.5.2 Clear Channel Assessment threshold . 17
4.5.2.0 Applicability. 17
4.5.2.1 Description . 17
4.5.2.2 Limits . 17
4.5.2.3 Conformance . 17
4.5.3 Polite spectrum access timing parameters . 17
4.5.3.1 Applicability. 17
4.5.3.2 Limits . 17
4.5.3.3 Conformance . 17
4.5.4 Adaptive Frequency Agility . 17
4.5.4.0 Applicability. 17
4.5.4.1 Description . 17
4.5.4.2 Limits . 17
4.5.4.3 Conformance . 17
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 18
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to
1 000 MHz . 20
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)
Annex C (normative): National Radio Interfaces not EU wide harmonised . 23
Annex D (informative): Application form for testing . 27
D.1 Introduction . 27
D.2 Information to declare according to ETSI EN 300 220-2 . 27
Annex E (informative): Selection of technical parameters . 29
E.1 Introduction . 29
E.2 Receiver parameters . 29
Annex F (informative): Bibliography . 30
Annex G (informative): Change History . 31
History . 32

ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
For non EU countries the present document may be used for regulatory (Type Approval) purposes.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)
Introduction
The present document is part 2 of a multi-part deliverable covering Short Range Devices (SRD) operating in the
frequency range 25 MHz to 1 000 MHz. Full details of the entire series can be found in part 1 [1].
The present document is structured as follows:
Clause 2 provides references.
Clause 3 provides definitions of terms and abbreviations used.
Clause 4 provides technical requirements.
Annex A (informative) provides a relationship between the present document and essential requirements of
Directive 2014/53/EU [i.2].
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to 1 000 MHz.
Annex C (normative): National Radio Interfaces not EU wide harmonised.
Annex D (informative): Application form for testing.
Annex E (informative): Selection of parameters.
Annex F (informative): Bibliography.
Annex G (informative): Change History.
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)
1 Scope
The present document specifies technical characteristics and methods of measurements for Non-specific Short Range
Devices category equipment types.
Non specific SRDs category is defined by the EU Commission Decision 2013/752/EU [i.3] as:
"The non-specific short-range device category covers all kinds of radio devices, regardless of the application or the
purpose, which fulfil the technical conditions as specified for a given frequency band. Typical uses include telemetry,
telecommand, alarms, data transmissions in general and other applications".
The present document covers equipment intended for fixed, mobile or nomadic use, including:
• stand-alone radio equipment;
• plug-in radio devices intended for use with or within a variety of host systems;
• plug-in radio devices intended for use within combined equipment.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: SRDs frequency ranges
Short Range Devices frequency ranges
Transmit and receive 26,957 MHz to 27,283 MHz
Transmit and receive 40,660 MHz to 40,700 MHz
Transmit and receive 138,2 MHz to 138,45 MHz
Transmit and receive 169,4 MHz to 169,8125 MHz
Transmit and receive 433,040 MHz to 434,790 MHz
Transmit and receive 863 MHz to 876 MHz
Transmit and receive 915 MHz to 921 MHz
NOTE: It should be noted that not all frequency bands in table 1 are implemented in all European
countries. Annex B provides an overview of radio interfaces which are harmonised in the
European Union. Annex C provides an overview of national radio interfaces not harmonised in
the European Union.

It is noted that in the European Commission Decision on Short Range Devices [i.3], some harmonised frequency bands
may be subject to usage restrictions such as the exclusion of video or audio use.
Equipment transmitting voice with analog modulation are excluded from the present document.
The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 300 220-2 V3.1.1 (2016-11)
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 220-1 (V3.1.1) (11-2016): "Short Range Devices (SRD) operating in the frequency
range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for th
...

Draft ETSI EN 300 220-2 V3.1.0 (2016-05)






HARMONISED EUROPEAN STANDARD
Short Range Devices (SRD) operating in
the frequency range 25 MHz to 1 000 MHz;
Part 2: Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU
for non specific radio equipment

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)



Reference
REN/ERM-TG28-534
Keywords
Harmonised standard, radio, SRD, testing

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 All equipment conformance requirements . 10
4.2.0 Compliance . 10
4.2.1 Operating frequency . 10
4.2.1.1 Description . 10
4.2.1.2 Limits . 10
4.2.1.3 Conformance . 10
4.2.2 Unwanted emissions in the spurious domain . 10
4.2.2.1 Description . 10
4.2.2.2 Limits . 10
4.2.2.3 Conformance . 10
4.3 Transmitters conformance requirements . 10
4.3.1 Effective Radiated Power . 10
4.2.1.0 Applicability. 10
4.3.1.1 Description . 10
4.3.1.2 Limits . 11
4.3.1.3 Conformance . 11
4.3.2 Maximum e.r.p spectral density . 11
4.3.2.0 Applicability. 11
4.3.2.1 Description . 11
4.3.2.2 Limits . 11
4.3.2.3 Conformance . 11
4.3.3 Duty Cycle . 11
4.3.3.0 Applicability. 11
4.3.3.1 Description . 11
4.3.3.2 Limits . 11
4.3.3.3 Conformance . 11
4.3.4 Occupied Bandwidth. 11
4.3.4.0 Applicability. 11
4.3.4.1 Description . 11
4.3.4.2 Limits . 12
4.3.4.3 Conformance . 12
4.3.5 Tx Out Of Band Emissions . 12
4.3.5.0 Applicability. 12
4.3.5.1 Description . 12
4.3.5.2 Limits . 12
4.3.5.3 Conformance . 12
4.3.6 Transient power . 12
4.3.6.0 Applicability. 12
4.3.6.1 Description . 12
4.3.6.2 Limits . 12
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)
4.3.6.3 Conformance . 12
4.3.7 Adjacent Channel Power . 12
4.3.7.0 Applicability. 12
4.3.7.1 Description . 12
4.3.7.2 Limits for equipment with operating channel width less than 25 kHz . 12
4.3.7.3 Conformance . 13
4.3.8 TX behaviour under Low Voltage Conditions . 13
4.3.8.0 Applicability. 13
4.3.8.1 Description . 13
4.3.8.2 Limits . 13
4.3.8.3 Conformance . 13
4.3.9 Adaptive Power Control . 13
4.3.9.0 Applicability. 13
4.3.9.1 Description . 13
4.3.9.2 Limits . 13
4.3.9.3 Conformance . 13
4.3.10 FHSS equipment . 13
4.3.10.0 Applicability. 13
4.3.10.1 Description . 13
4.3.10.2 Limits . 14
4.3.10.3 Conformance . 14
4.3.11 Short term behaviour . 14
4.3.11.0 Applicability. 14
4.3.11.1 Description . 15
4.3.11.2 Limits . 15
4.3.11.3 Conformance . 15
4.4 Receivers conformance requirements . 15
4.4.1 RX sensitivity . 15
4.4.1.0 Applicability. 15
4.4.1.1 Description . 15
4.4.1.2 Limits . 15
4.4.1.3 Conformance . 15
4.4.2 Blocking . 15
4.4.2.0 Applicability. 15
4.4.2.1 Description . 15
4.4.2.2 Limits . 15
4.4.2.3 Conformance . 15
4.4.3 Clear Channel Assessment threshold . 15
4.4.3.0 Applicability. 15
4.4.3.1 Description . 16
4.4.3.2 Limits . 16
4.4.3.3 Conformance . 16
4.4.4 Polite spectrum access . 16
4.4.4.0 Applicability. 16
4.4.4.1 Description . 16
4.4.4.2 Limits . 16
4.4.4.3 Conformance . 16
4.5 Other conformance requirements . 16
4.5.1 Adaptive Frequency Agility . 16
4.5.1.0 Applicability. 16
4.5.1.1 Description . 16
4.5.1.2 Conformance . 16
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 17
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to
1 000 MHz . 19
Annex C (normative): National Radio Interfaces not EU wide harmonised . 22
Annex D (informative): Application form for testing . 27
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)
D.1 Introduction . 27
D.2 Information to declare according to ETSI EN 300 220-2 . 27
Annex E (informative): Selection of technical parameters . 29
E.1 Introduction . 29
E.2 Receiver parameters . 29
Annex F (informative): Bibliography . 30
Annex G (informative): Change History . 31
History . 32

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.5] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in Table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
For non EU countries the present document may be used for regulatory (Type Approval) purposes.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)
Introduction
The present document is part 2 of a multi-part deliverable, covering non specific Short Range Devices (SRD) operating
in the frequency range 25 MHz to 1 000 MHz. Full details of the entire series can be found in part 1 [1].
The present document is structured as follows:
Clause 2 provides references.
Clause 3 provides definitions of terms and abbreviations used.
Clause 4 provides technical requirements.
Annex A (normative) provides a relationship between the present document and essential requirements of
Directive 2014/53/EU [i.2].
Annex B (normative): EU wide harmonised national radio interfaces from 25 MHz to 1 000 MHz.
Annex C (informative): National Radio Interfaces not EU wide harmonised.
Annex D (informative): Application form for testing.
Annex E (informative): Selection of parameters.
Annex F (informative): Bibliography.
Annex G (informative): Change History.
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)
1 Scope
The present document applies to Non-specific Short Range Devices category equipment types.
Non specific SRDs category is defined by the EU Commission Decision 2013/752/EU [i.3] as:
"The non-specific short-range device category covers all kinds of radio devices, regardless of the application or the
purpose, which fulfil the technical conditions as specified for a given frequency band. Typical uses include telemetry,
telecommand, alarms, data transmissions in general and other applications".
The present document covers equipment intended for fixed, mobile or nomadic use, e.g.:
• stand-alone radio equipment;
• plug-in radio devices intended for use with or within a variety of host systems;
• plug-in radio devices intended for use within combined equipment.
These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1.
Table 1: SRDs frequency ranges
Short Range Devices frequency ranges
Transmit and receive 26,957 MHz to 27,283 MHz
Transmit and receive 40,660 MHz to 40,700 MHz
Transmit and receive 138,2 MHz to 138,45 MHz
Transmit and receive 169,4 MHz to 169,8125 MHz
Transmit and receive 433,040 MHz to 434,790 MHz
Transmit and receive 863 MHz to 876 MHz
Transmit and receive 915 MHz to 921 MHz
NOTE: It should be noted that not all frequency bands in table 1 are implemented in all European
countries. Annex B provides an overview of radio interfaces which are harmonised in the
European Union. Annex C provides an overview of national radio interfaces not harmonised in
the European Union.

It is noted that in the European Commission Decision on Short Range Devices [i.3], some harmonised frequency bands
may be subject to usage restrictions such as the exclusion of video or audio use.
Equipment transmitting voice with analog modulation are excluded from the present document.
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 220-1 (V3.1.0) (05-2016): "Short Range Devices (SRD) operating in the frequency
range 25 MHz to 1 000 MHz; Part 1: Technical characteristics and methods of measurement".
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 300 220-2 V3.1.0 (2016-05)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] CEPT/ERC/REC 70-03: "Relating to the use of Short Range Devices (SRD)".
NOTE: Available at http://www.erodocdb.dk/docs/doc98/official/pdf/rec7003e.pdf.
[i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of
...