EN IEC 61169-60:2021

SLOVENSKI STANDARD
01-julij-2021
Radiofrekvenčni konektorji - 60. del: Področna specifikacija za radiofrekvenčne
(RF) koaksialne konektorje s potisnim osnim spajanjem - Karakteristična
impedanca 50 Ohm (tip SMPM) (IEC 61169-60:2021)
Radio-frequency connectors - Part 60: Sectional specification for RF coaxial connectors
with push on mating - Characteristic impedance 50 Ohm (type SMPM) (IEC 61169-
60:2021)
Hochfrequenz-Steckverbinder - Teil 60: Rahmenspezifikation für koaxiale HF-
Steckverbinder mit Innendurchmesser des Außenleiters in mm Push-On / SMPM Typ -
Wellenwiderstand 50 Ohm (IEC 61169-60:2021)
Connecteurs pour fréquences radioélectriques - Partie 60: Spécification intermédiaire
relative aux connecteurs coaxiaux pour fréquences radioélectriques avec couplage par
poussée - Impédance caractéristique 50 Ohm (type SMPM) (IEC 61169-60:2021)
Ta slovenski standard je istoveten z: EN IEC 61169-60:2021
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61169-60

NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2021
ICS 33.120.30
English Version
Radio-frequency connectors - Part 60: Sectional specification for
RF coaxial connectors with push on mating - Characteristic
impedance 50 Ohm (type SMPM)
(IEC 61169-60:2021)
Connecteurs pour fréquences radioélectriques - Partie 60: Hochfrequenz-Steckverbinder - Teil 60:
Spécification intermédiaire relative aux connecteurs Rahmenspezifikation für koaxiale HF-Steckverbinder mit
coaxiaux pour fréquences radioélectriques avec couplage Push-On Verbindung - Wellenwiderstand 50 Ohm (Typ
par poussée - Impédance caractéristique 50 Ohm (type SMPM)
SMPM) (IEC 61169-60:2021)
(IEC 61169-60:2021)
This European Standard was approved by CENELEC on 2021-04-21. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61169-60:2021 E

European foreword
The text of document 46F/548/FDIS, future edition 1 of IEC 61169-60, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-60:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-01-21
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-04-21
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Standard IEC 61169-60:2021 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General and EN 60068-1 -
guidance
IEC 61169-1 2013 Radio frequency connectors - Part 1: EN 61169-1 2013
Generic specification - General requirements
and measuring methods
IEC 62037 series RF connectors, connector cable assemblies EN IEC 62037 series
and cables - Intermodulation level
measurement
IEC 61169-60 ®
Edition 1.0 2021-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Radio-frequency connectors –
Part 60: Sectional specification for RF coaxial connectors with push on mating –

Characteristic impedance 50 Ohm (type SMPM)

Connecteurs pour fréquences radioélectriques –

Partie 60: Spécification intermédiaire relative aux connecteurs coaxiaux pour

fréquences radioélectriques avec couplage par poussée – Impédance

caractéristique 50 Ohm (type SMPM)

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.30 ISBN 978-2-8322-9541-0

– 2 – IEC 61169-60:2021 © IEC 2021
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Mating face and gauge information . 7
4.1 Dimensions – General connectors – Grade 2 . 7
4.1.1 SMPM connector with pin-centre contact . 7
4.1.2 SMPM connector with socket-centre contact (see Figure 3) . 9
4.2 SMPM gauges . 10
4.2.1 SMPM gauge pin for socket-centre contact . 10
4.2.2 Gauges for outer contact of SMPM connector with socket-centre contact. 11
5 Quality assessment procedure . 19
5.1 General . 19
5.2 Rating and characteristics (see Clause 5 of IEC 61169-1:2013) . 19
5.3 Test schedule and inspection requirements. 22
5.3.1 Acceptance tests . 22
5.3.2 Periodic tests . 22
5.4 Procedures for the quality conformance . 24
5.4.1 Quality conformance inspection . 24
5.4.2 Quality conformance and its maintenance . 24
6 Instructions for preparation of detail specifications (DS) . 24
6.1 General . 24
6.2 Identification of the component . 24
6.3 Performances . 25
6.4 Marking, ordering information and related matters . 25
6.5 Selection of tests, test conditions and severities . 25
6.6 Blank detail specification pro-forma for type SMPM connector . 26
7 Marking . 30
7.1 Marking of component . 30
7.2 Marking and contents of package . 30

Figure 1 – SMPM connector with pin-centre contact – Full detent (for dimensions, see
Table 1) . 7
Figure 2 – SMPM connector with pin-centre contact – Smooth bore (for dimensions,
see Table 2) . 8
Figure 3 – SMPM connector with socket-centre contact (for dimensions, see Table 3) . 9
Figure 4 – SMPM gauge pin for socket-centre contact (for dimensions, see Table 4) . 10
Figure 5 – SMPM engagement force gauge – Full detent (for dimensions, see Table 5) . 11
Figure 6 – SMPM Separation force gauge – Full detent (for dimensions, see Table 6) . 13
Figure 7 – SMPM Engagement force gauge – Smooth bore (for dimensions, see Table
7) . 15
Figure 8 – SMPM Separation force gauge – Smooth bore (for dimensions, see Table 8) . 17
Figure 9 – SMPM gauge block (for dimensions, see Table 9) . 18

Table 1 – Dimensions of SMPM connector with pin-centre contact full detent . 7

IEC 61169-60:2021 © IEC 2021 – 3 –
Table 2 – Dimensions of SMPM connector with pin-centre contact – Smooth bore . 8
Table 3 – Dimensions of SMPM connector with socket-centre contact. 9
Table 4 – Dimensions of SMPM gauge pin for socket-centre contact . 10
Table 5 – Dimensions of SMPM engagement force gauge – Full detent . 12
Table 6 – Dimensions of SMPM separation force gauge – Full detent . 14
Table 7 – Dimensions of SMPM engagement force gauge – Smooth bore . 16
Table 8 – Dimensions of SMPM separation force gauge – Smooth bore . 18
Table 9 – Dimensions of SMPM gauge block . 19
Table 10 – Preferred climatic categories (see IEC 60068-1) . 19
Table 11 – Rating and characteristics . 20
Table 12 – Acceptance tests . 22
Table 13 – Periodic tests . 23

– 4 – IEC 61169-60:2021 © IEC 2021
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 60: Sectional specification for RF coaxial connectors with push
on mating – Characteristic impedance 50 Ohm (type SMPM)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement
...