EN 60317-0-7:2012

SLOVENSKI STANDARD
01-september-2012
Specifikacije za posebne vrste navijalnih žic - 0-7. del: Splošne zahteve -
Popolnoma izolirana in brezhibno lakirana okrogla bakrena žica z nazivnim
premerom vodnika od 0,040 mm do 1,600 mm
Specifications for particular types of winding wires - Part 0-7: General requirements -
Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor
diameter of 0,040 mm to 1,600 mm
Technische Lieferbedingungen für bestimmte Typen von Wickeldrähten - Teil 0-7:
Allgemeine Anforderungen - Isolationsfehlerfreie Runddrähte (FIW) aus Kupfer,
lackisoliert mit Nenndurchmesser von 0,040 mm bis 1,600 mm
Spécifications pour types particuliers de fils de bobinage - Partie 0-7: Exigences
générales - Fil de section circulaire en cuivre émaillé sans défaut d'isolation électrique
avec diamètre nominal de conducteur compris entre 0,040 mm et 1,600 mm
Ta slovenski standard je istoveten z: EN 60317-0-7:2012
ICS:
29.060.10 Žice Wires
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60317-0-7
NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM
ICS 29.060.10
English version
Specifications for particular types of winding wires -
Part 0-7: General requirements -
Fully insulated (FIW) zero-defect enamelled round copper wire with
nominal conductor diameter of 0,040 mm to 1,600 mm
(IEC 60317-0-7:2012)
Spécifications pour types particuliers de Technische Lieferbedingungen für
fils de bobinage - bestimmte Typen von Wickeldrähten -
Partie 0-7: Exigences générales - Teil 0-7: Allgemeine Anforderungen -
Fil de section circulaire en cuivre émaillé Isolationsfehlerfreie Runddrähte (FIW) aus
sans défaut d'isolation électrique avec Kupfer, lackisoliert mit Nenndurchmesser
diamètre nominal de conducteur compris von 0,040 mm bis 1,600 mm
entre 0,040 mm et 1,600 mm (IEC 60317-0-7:2012)
(CEI 60317-0-7:2012)
This European Standard was approved by CENELEC on 2012-05-24. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60317-0-7:2012 E
Foreword
The text of document 55/1303/FDIS, future edition 1 of IEC 60317-0-7, prepared by IEC/TC 55 "Winding
wires" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN 60317-0-
7:2012.
The following dates are fixed:
(dop) 2013-02-24
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2015-05-24
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This European Standard is to be read in conjunction with the EN 60851 series.
The clause numbers used in EN 60317-0-7:2012 are identical with the respective test numbers of the
EN 60851 series.
In case of inconsistencies between EN 60851 and EN 60317-0-7:2012, the latter shall prevail.
The numbering of clauses in this standard is not continuous from Clauses 21 and 30 in order to reserve
space for possible future wire requirements prior to those for wire packaging.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 60317-0-7:2012 was approved by CENELEC as a European
Standard without any modification.

- 3 - EN 60317-0-7:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 60172 - Test procedure for the determination of the EN 60172 -
temperature index of enamelled winding wires

IEC 60317-0-1 2008 Specifications for particular types of winding EN 60317-0-1 2008
wires -
Part 0-1: General requirements - Enamelled
round copper wire
IEC 60851 Series Winding wires - Test methods EN 60851 Series

IEC 60851-5 2008 Winding wires - Test methods - EN 60851-5 2008
+ A1 2011 Part 5: Electrical properties + A1 2011

ISO 3 - Preferred numbers - Series of preferred - -
numbers
IEC 60317-0-7 ®
Edition 1.0 2012-04
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Specifications for particular types of winding wires –

Part 0-7: General requirements – Fully insulated (FIW) zero-defect enamelled

round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm

Spécifications pour types particuliers de fils de bobinage –

Partie 0-7: Exigences générales – Fil de section circulaire en cuivre émaillé sans

défaut d'isolation électrique avec diamètre nominal de conducteur compris entre

0,040 mm et 1,600 mm
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
R
CODE PRIX
ICS 29.060.10 ISBN 978-2-8322-0079-7

– 2 – 60317-0-7  IEC:2012
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions, general notes and appearance . 7
3.1 Terms and definitions . 7
3.2 General notes. 9
3.2.1 Methods of test . 9
3.2.2 Winding wire . 9
3.3 Appearance . 9
4 Dimensions . 9
4.1 Conductor diameter . 9
4.2 Out of roundness of conductor (for nominal diameters over 0,063 mm). 10
4.3 Minimum overall diameter . 10
4.4 Maximum overall diameter . 10
5 Electrical resistance . 13
6 Elongation . 13
7 Springiness . 14
8 Flexibility and adherence . 14
8.1 Mandrel winding test (for nominal conductor diameters up to and including
1,600 mm) . 14
8.2 Jerk test (for nominal diameters up to and including 1,000 mm) . 15
9 Heat shock . 15
10 Cut Through . 16
11 Resistance to abrasion . 16
12 Resistance to solvents . 16
13 Breakdown voltage . 17
14 Continuity of insulation (nominal conductor diameters up to and including
1,600 mm) . 17
14.1 Off-line high voltage continuity . 17
14.2 In-line high voltage continuity . 17
15 Temperature index . 17
16 Resistance to refrigerants . 17
17 Solderability . 18
18 Heat or solvent bonding . 18
19 Dielectric dissipation factor . 18
20 Resistance to transformer oil . 18
21 Loss of mass . 18
23 Pin-hole test . 18
30 Packaging . 18
Annex A (informative) Dimensions for intermediate nominal conductor diameter values
(R 40) . 19

60317-0-7  IEC:2012 – 3 –
Table 1 – Dimensions of enamelled wires (R 20) (1 of 2) . 11
Table 2 – Electrical resistance . 13
Table 3 – Elongation at break . 13
Table 4 – Springiness . 14
Table 5 – Mandrel diameters for mandrel winding test . 15
Table 6 – Heat shock . 16
Table 7 – Breakdown voltage . 17
Table A.1 – Dimensions of enamelled wires without a bonding layer (R 40) . 19

– 4 – 60317-0-7  IEC:2012
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
SPECIFICATIONS FOR PARTICULAR TYPES
OF WINDING WIRES –
Part 0-7: General requirements –
Fully insulated (FIW) zero-defect enamelled round copper wire
with nominal conductor diameter of 0,040 mm to 1,600 mm

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may part
...