EN IEC 61169-63:2020

SLOVENSKI STANDARD
01-oktober-2020
Radiofrekvenčni konektorji - 63. del: Področna specifikacija - Radiofrekvenčni (RF)
koaksialni konektorji z notranjim premerom zunanjega vodnika 6,5 mm (0,256 in) z
bajonetnim zaklepom - Karakteristična impedanca 75 ohm (tip BNC75) (IEC 61169-
63:2020)
Radio-frequency connectors - Part 63: Sectional specification - RF coaxial connectors
with inner diameter of outer conductor 6,5 mm (0,256 in) with bayonet lock -
Characteristic impedance 75 ohms (type BNC75) (IEC 61169-63:2020)
Hochfrequenz-Steckverbinder - Teil 63: Rahmenspezifikation – Koaxiale
Hochfrequenzsteckverbinder mit 6,5 mm (0,256 in) Innendurchmesser des Außenleiters
und Bajonettverschluss – Wellenwiderstand 75 Ohm (Typ BNC75) (IEC 61169-63:2020)
Connecteurs pour fréquences radioélectriques - Partie 63: Spécification intermédiaire -
Connecteurs coaxiaux pour fréquences radioélectriques avec diamètre intérieur du
conducteur extérieur de 6,5 mm (0,256 in) à verrouillage à baïonnette - Impédance
caractéristique 75 ohms (type BNC75) (IEC 61169-63:2020)
Ta slovenski standard je istoveten z: EN IEC 61169-63:2020
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61169-63

NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2020
ICS 33.120.30
English Version
Radio-frequency connectors - Part 63: Sectional specification -
RF coaxial connectors with inner diameter of outer conductor 6,5
mm (0,256 in) with bayonet lock - Characteristic impedance 75
ohms (type BNC75)
(IEC 61169-63:2020)
Connecteurs pour fréquences radioélectriques - Partie 63: Hochfrequenz-Steckverbinder - Teil 63:
Spécification intermédiaire - Connecteurs coaxiaux pour Rahmenspezifikation - Koaxiale
fréquences radioélectriques avec diamètre intérieur du Hochfrequenzsteckverbinder mit 6,5 mm (0,256 in)
conducteur extérieur de 6,5 mm (0,256 in) à verrouillage à Innendurchmesser des Außenleiters und
baïonnette - Impédance caractéristique 75 ohms (type Bajonettverschluss - Wellenwiderstand 75 Ohm (Typ
BNC75) BNC75)
(IEC 61169-63:2020) (IEC 61169-63:2020)
This European Standard was approved by CENELEC on 2020-06-30. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61169-63:2020 E

European foreword
The text of document 46F/501/FDIS, future edition 1 of IEC 61169-63, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-63:2020.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2021-03-30
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-06-30
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61169-63:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60068-2-1:2007 NOTE Harmonized as EN 60068-2-1:2007 (not modified)
IEC 60068-2-2:2007 NOTE Harmonized as EN 60068-2-2:2007 (not modified)
IEC 60068-2-11:1981 NOTE Harmonized as EN 60068-2-11:1999 (not modified)
IEC 60068-2-13:1983 NOTE Harmonized as EN 60068-2-13:1999 (not modified)
IEC 60068-2-14:2009 NOTE Harmonized as EN 60068-2-14:2009 (not modified)
IEC 60068-2-20:2008 NOTE Harmonized as EN 60068-2-20:2008 (not modified)
IEC 60068-2-30:2005 NOTE Harmonized as EN 60068-2-30:2005 (not modified)

Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 - Environmental testing - Part 1: General and EN 60068-1 -
guidance
IEC 61169-1 2013 Radio frequency connectors - Part 1: Generic EN 61169-1 2013
specification - General requirements and
measuring methods
IEC 61169-63 ®
Edition 1.0 2020-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Radio-frequency connectors –
Part 63: Sectional specification – RF coaxial connectors with inner diameter of

outer conductor 6,5 mm (0,256 in) with bayonet lock – Characteristic

impedance 75 Ω (type BNC75)
Connecteurs pour fréquences radioélectriques –

Partie 63: Spécification intermédiaire – Connecteurs coaxiaux pour fréquences

radioélectriques avec diamètre intérieur du conducteur extérieur de 6,5 mm

(0,256 in) à verrouillage à baïonnette – Impédance caractéristique 75 Ω

(type BNC75)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.120.30 ISBN 978-2-8322-8221-2

– 2 – IEC 61169-63:2020 © IEC 2020
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 IEC type designation. 7
5 Interface dimensions – General purpose connectors . 7
5.1 Pin connector . 7
5.2 Socket connector . 9
6 Mechanical gauges and standard test connectors . 11
6.1 Mechanical gauges . 11
6.1.1 Connectors with pin-centre contact . 11
6.1.2 Connectors with socket-centre contact . 12
6.1.3 Gauge for outer contacts, coupling mechanism and mating face
dimensions . 13
6.2 Standard test connectors . 14
6.2.1 General . 14
6.2.2 Standard test connector with pin contact . 14
6.2.3 Standard test connector with socket contact . 15
7 Outline dimensions . 17
8 Quality assessment procedures . 17
8.1 General . 17
8.2 Ratings and characteristics . 17
8.3 Test schedule and inspection requirements . 20
8.3.1 Acceptance tests . 20
8.3.2 Periodic tests . 21
8.4 Procedures for quality conformance . 22
8.4.1 Quality conformance inspection . 22
8.4.2 Qualification approval and its maintenance . 22
9 Instructions for preparation of detail specifications . 22
9.1 General . 22
9.2 Identification of the component . 23
9.3 Performance . 23
9.4 Marking, ordering information and related matters . 23
9.5 Selection of tests, test conditions and severities . 23
9.6 Blank detail specification pro-forma for type BNC connector . 23
Bibliography . 29

Figure 1 – Connector with pin-centre contact . 7
Figure 2 – Details of bayonet lock . 7
Figure 3 – Details of alternative coupling grooves . 8
Figure 4 – Details of alternative coupling grooves . 8
Figure 5 – Details of pin-centre contact . 8
Figure 6 – Connector with socket-centre contact . 10
Figure 7 – Details of socket-centre contact . 10
Figure 8 – Gauge for outer contact of pin connector . 11

IEC 61169-63:2020 © IEC 2020 – 3 –
Figure 9 – Gauge pin for socket-centre contact . 12
Figure 10 – Dimensions of gauge for performance test . 13
Figure 11 – Dimensions of connector . 14
Figure 12 – Dimensions of centre contact . 15
Figure 13 – Dimensions of connector . 16
Figure 14 – Dimensions of centre contact . 16

Table 1 – Dimensions for connector with pin-centre contact. 9
Table 2 – Dimensions for connector with socket-centre contact . 10
Table 3 – Dimensions for gauges for outer contact of pin connector . 12
Table 4 – Dimensions for gauge pin for socket-centre contact . 13
Table 5 – Dimensions of gauge for performance test .
...