EN IEC 61169-4:2022

SLOVENSKI STANDARD
01-januar-2023
Nadomešča:
SIST HD 134.4 S2:2002
Radiofrekvenčni konektorji - 4. del: Radiofrekvenčni (RF) konektorji z notranjim
premerom zunanjega vodnika 16 mm (0,63 in) z navojnim spajanjem -
Karakteristična impedanca 50 ohm (tip 7-16)
Radio-frequency connectors - Part 4: RF coaxial connectors with inner diameter of outer
conductor 16 mm (0,63 in) with screw lock - Characteristic impedance 50 Ω (type 7-16)
Hochfrequenz-Steckverbinder - Teil 4: Koaxiale Hochfrequenzsteckverbinder mit 16 mm
(0,63 in) Innendurchmesser des Außenleiters und Schraubverschluss -
Wellenwiderstand 50 Ohm (Typ 7-16)
Connecteurs pour fréquences radioélectriques - Partie 4: Connecteurs coaxiaux pour
fréquences radioélectriques de diamètre intérieur du conducteur extérieur de 16 mm
(0,63 in) à verrouillage à vis - Impédance caractéristique 50 Ω (type 7-16)
Ta slovenski standard je istoveten z: EN IEC 61169-4:2022
ICS:
33.120.30 Radiofrekvenčni konektorji RF connectors
(RF)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN IEC 61169-4

NORME EUROPÉENNE
EUROPÄISCHE NORM November 2022
ICS 29.120.10 Supersedes HD 134.4 S2:1977
English Version
Radio-frequency connectors - Part 4: RF coaxial connectors with
inner diameter of outer conductor 16 mm (0,63 in) with screw
lock - Characteristic impedance 50 Ω (type 7-16)
(IEC 61169-4:2008)
Connecteurs pour fréquences radioélectriques - Partie 4: Hochfrequenz-Steckverbinder - Teil 4: Koaxiale
Connecteurs coaxiaux pour fréquences radioélectriques de Hochfrequenzsteckverbinder mit 16 mm (0,63 in)
diamètre intérieur du conducteur extérieur de 16 mm (0,63 Innendurchmesser des Außenleiters und
in) à verrouillage à vis - Impédance caractéristique 50 Ω Schraubverschluss - Wellenwiderstand 50 Ohm (Typ 7-16)
(type 7-16) (IEC 61169-4:2008)
(IEC 61169-4:2008)
This European Standard was approved by CENELEC on 2022-10-11. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61169-4:2022 E

European foreword
The text of document 46F/60/FDIS, future edition 1 of IEC 61169-4, prepared by SC 46F "RF and
microwave passive components" of IEC/TC 46 "Cables, wires, waveguides, RF connectors, RF and
microwave passive components and accessories" was submitted to the IEC-CENELEC parallel vote
and approved by CENELEC as EN IEC 61169-4:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-07-11
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-10-11
document have to be withdrawn
This document supersedes HD 134.4 S2:1977 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61169-4:2008 was approved by CENELEC as a European
Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61169-1 - Radio-frequency connectors - Part 1: Generic - -
specification - General requirements and
measuring methods
IEC 62037 - RF connectors, connector cable assemblies - -
and cables - Intermodulation level
measurement
IEC 61169-4
Edition 1.0 2008-04
INTERNATIONAL
STANDARD
Radio-frequency connectors –
Part 4: RF coaxial connectors with inner diameter of outer conductor 16 mm
(0,63 in) with screw lock – Characteristic impedance 50 Ω (type 7-16)

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
T
ICS 29.120.10 ISBN 2-8318-9725-4

– 2 – 61169-4 © IEC:2008(E)
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 Mating face and gauge information.6
3.1 Dimensions –General connectors – Grade 2.7
3.1.1 Connector with pin centre contact.7
3.1.2 Connector with socket centre contact .8
3.2 Gauges for general purpose connectors - Grade 2 .9
3.2.1 Gauges for connector with socket centre contact .9
3.3 Dimensions – standard test connectors – Grade 0.10
3.3.1 Standard test connector with pin centre contact.10
3.3.2 Standard test connector with socket centre contact .10
4 Quality assessment procedures.11
4.1 General .11
4.2 Ratings and characteristics .11
4.3 Test Schedule and Inspection requirements .14
4.3.1 Acceptance tests .14
4.3.2 Periodic tests .15
4.4 Procedures.16
4.4.1 Quality conformance inspection .16
4.4.2 Qualification approval and its maintenance.16
5 Instructions for preparation of detail specifications .17
5.1 General .17
5.2 Identification of the Detail specification .17
5.3 Identification of the component.17
5.4 Performance.17
5.5 Marking, ordering information and related matters .18
5.6 Selection of tests, test conditions and severities.18
5.7 Blank detail specification pro-forma for type 7-16 connector .19

Figure 1 – Connector with pin centre contact .7
Figure 2 – Connector with socket centre contact.8
Figure 3 – Gauge pin for socket centre contact .9
Figure 4 – Gauge ring for socket outer contact.9
Figure 5 – Slotted centre contact .11

Table 1 – Connector with pin centre contact. .7
Table 2 – Connector with socket centre contact .8
Table 3 – Tolerance for the standard connector with pin centre contact. .10
Table 4 – Tolerance for the standard connector with socket centre contact.10
Table 5 – Slotted centre contact .11
Table 6 – Preferred climatic categories (see IEC 60068-1):.12
Table 7 – Ratings and characteristics .13

61169-4 © IEC:2008(E) – 3 –
Table 8 – Acceptance tests.14
Table 9 – Periodic tests .15

– 4 – 61169-4 © IEC:2008(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 4: RF coaxial connectors with inner diameter
of outer conductor 16 mm (0,63 in) with screw lock –
Characteristic impedance 50 Ω (type 7-16)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is
...