EN 61169-14:2010

SLOVENSKI STANDARD
01-januar-2011
5DGLRIUHNYHQþQLNRQHNWRUMLGHO5DGLRIUHNYHQþQL5)NRDNVLDOQLNRQHNWRUML]
QRWUDQMLPSUHPHURP]XQDQMHJDYRGQLNDPPLQQDYRMQLPVSDMDQMHP
.DUDNWHULVWLþQDLPSHGDQFDRKPRYWLS,(&
Radio-frequency connectors - Part 14: R.F. coaxial connectors with inner diameter of
outer conductor 12 mm with screw coupling - Characteristic impedance 75 ohms (Type
3.5/12) (IEC 61169-14:2010)
Hochfrequenz-Steckverbinder - Teil 14: Koaxiale HF-Steckverbinder mit 12 mm
Innendurchmesser des Außenleiters mit Schraubverbindung - Wellenwiderstand 75 Ohm
(Typ 3,5/12) (IEC 61169-14:2010)
Connecteurs pour fréquences radioélectriques - Partie 14: Connecteurs coaxiaux pour
fréquences de diamètre intérieur du conducteur extérieur de 12 mm à verrouillage à vis -
- Impédance caractéristique 75 ohms (Type 3,5/12) (CEI 61169-14:2010)
Ta slovenski standard je istoveten z: EN 61169-14:2010
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 61169-14
NORME EUROPÉENNE
December 2010
EUROPÄISCHE NORM
ICS 33.120.30
English version
Radio-frequency connectors -
Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12
mm with screw coupling -
Characteristic impedance 75 ohms (Type 3,5/12)
(IEC 61169-14:2010)
Connecteurs pour fréquences Hochfrequenz-Steckverbinder -
radioélectriques - Teil 14: Koaxiale HF-Steckverbinder mit
Partie 14: Connecteurs coaxiaux pour 12 mm Innendurchmesser des
fréquences de diamètre intérieur du Außenleiters mit Schraubverbindung -
conducteur extérieur de 12 mm à Wellenwiderstand 75 Ohm (Typ 3,5/12)
verrouillage à vis - (IEC 61169-14:2010)
Impédance caractéristique 75 ohms (Type
3,5/12)
(CEI 61169-14:2010)
This European Standard was approved by CENELEC on 2010-12-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61169-14:2010 E
Foreword
The text of document 46F/148/CDV, future edition 1 of IEC 61169-14, prepared by IEC/SC 46F, R.F. and
microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and
microwave passive components and accessories, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 61169-14 on 2010-12-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-12-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61169-14:2010 was approved by CENELEC as a European
Standard without any modification.
__________
- 3 - EN 61169-14:2010
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year

IEC 61169-1 1992 Radio-frequency connectors - EN 61169-1 1994
+ A1 1996 Part 1: Generic specification - General + A1 1996
+ A2 1997 requirements and measuring methods + A2 1997

IEC 61169-14 ®
Edition 1.0 2010-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Radio-frequency connectors –
Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm
with screw coupling – Characteristic impedance 75 ohms (Type 3,5/12)

Connecteurs pour fréquences radioélectriques –
Partie 14: Connecteurs coaxiaux pour fréquences de diamètre intérieur du
conducteur extérieur de 12 mm à verrouillage à vis – Impédance caractéristique
75 ohms (Type 3,5/12)
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
U
CODE PRIX
ICS 33.120.30 ISBN 978-2-88912-161-8
– 2 – 61169-14 © IEC:2010
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 IEC type designation .6
4 Mating face for general purpose connector .7
4.1 Connector with pin centre contact.7
(see Figure 1).7
4.2 Connector with socket centre contact .8
(see Figure 2).8
5 Gauges and standard test connectors .9
5.1 Mechanical gauges.9
5.1.1 Socket connector.9
5.2 Standard test connectors (Grade 0).9
5.2.1 General .9
5.2.2 Standard test connectors with pin centre contact .9
5.2.3 Standard test connectors with socket centre contact.10
6 Survey of patterns .10
7 Outline dimensions.12
8 Quality assessment procedures.16
8.1 General .16
8.2 Ratings and characteristics .16
8.3 Test schedule and inspection requirements .18
8.3.1 Acceptance tests .18
8.3.2 Periodic tests .19
8.4 Procedures.20
8.4.1 Quality conformance inspection .20
8.4.2 Qualification approval and its maintenance.20
9 Instructions for preparation of detail specifications .21
9.1 General .21
9.2 Identification of the detail specification .22
9.3 Identification of the component.22
9.4 Performance.22
9.5 Marking, ordering information and related matters .22
9.6 Selection of tests, test conditions and severities.22
10 Blank detail specification pro-forma for type 3.5/12 connector .24

Figure 1 – Connector with pin centre contact (for dimensions, see Table 1) .
Figure 2 – Connector with socket centre contact (for dimensions, see Table 2).8
Figure 3 – Gauge pins for centre contact of socket connector .9
Figure 4 – Slotted centre contact .10

Table 1 – Dimensions for connector with pin centre contact .7
Table 2 – Dimensions for connector with socket centre contact.8
Table 3 – Dimensions for connector with pin centre contact Grade 0 .9

61169-14 © IEC:2010 – 3 –
Table 4 – Dimensions for connector with socket centre contact Grade 0 .10
Table 5 – Survey of patterns .10
Table 6 – Outline dimensions.13
Table 7 – Rating and characteristic.16
Table 8 – Acceptance tests.18
Table 9 – Periodic tests .19

– 4 – 61169-14 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
RADIO-FREQUENCY CONNECTORS –
Part 14: R.F. coaxial connectors with inner diameter
of outer conductor 12 mm with screw coupling –
Characteristic impedance 75 ohms (Type 3,5/12)

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification
...