iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CLC

EN 50463-2:2017

(Main)

Railway applications - Energy measurement on board trains - Part 2: Energy measuring

Railway applications - Energy measurement on board trains - Part 2: Energy measuring

This European Standard covers the requirements applicable to the Energy Measurement Function (EMF) of an Energy Measurement System (EMS) for use on board traction units for measurement of energy supplied directly from/to the Contact Line system. This European Standard also gives requirements for the Current Measurement Function (e.g. current sensor), the Voltage Measurement Function (e.g. voltage sensor) and the Energy Calculation Function (e.g. energy meter). The Conformity Assessment arrangements for the Voltage Measurement Function, Current Measurement Function, the Energy Calculation Function and a complete Energy Measurement Function are also specified in this document. The standard has been developed taking into account that in some applications the EMF can be subjected to legal metrological control. All relevant metrological aspects are covered in this part. Figure 2 shows the flow between the functional blocks of the EMF. Only connections between the functional blocks required by this standard are displayed. (...)

Bahnanwendungen - Energiemessung auf Bahnfahrzeugen - Teil 2: Energiemessung

Applications ferroviaires - Mesure d'énergie à bord des trains - Partie 2 : Mesure d'énergie

La présente Norme européenne couvre les exigences applicables à la fonction de mesure d’énergie (EMF) d’un système de mesure d’énergie (EMS) à utiliser à bord des unités de traction pour mesurer l’énergie directement récupérée au niveau du système de ligne de contact ou envoyée à ce dernier. La présente Norme européenne spécifie également les exigences pour la fonction de mesure de courant (par exemple, capteur de courant), la fonction de mesure de tension (par exemple, capteur de tension) et la fonction de calcul d'énergie (par exemple, compteur d'énergie). Les dispositions relatives à l'évaluation de la conformité pour la fonction de mesure de tension, la fonction de mesure de courant, la fonction de calcul d'énergie et l'ensemble d'une fonction de mesure d'énergie sont également spécifiées dans ce document. Cette norme a été élaborée en tenant compte du fait que, dans certaines applications, l'EMF peut être soumise à un contrôle métrologique réglementaire. Toutes les caractéristiques métrologiques pertinentes sont traitées dans la présente partie. La Figure 2 présente le flux entre les blocs fonctionnels de l'EMF. Seules les connexions entre les blocs fonctionnels requises par la présente norme sont représentées. (...)

Železniške naprave - Merjenje energije na vlaku - 2. del: Merjenje energije

Ta osnutek evropskega standarda zajema zahteve za funkcijo merjenja energije (EMF) sistema merjenja energije (EMS), ki se uporablja na vlakovnih kompozicijah za merjenje energije, dovajane neposredno iz sistema kontaktnega vodnika ali vanj.
Ta osnutek evropskega standarda določa tudi zahteve za funkcijo merjenja toka (npr. tokovni senzor), funkcijo merjenja napetosti (npr. napetostni senzor) in funkcijo izračuna energije (npr. števec energije).
V tem dokumentu so navedeni tudi načini ugotavljanja skladnosti funkcije merjenja napetosti, funkcije merjenja toka, funkcije izračuna energije in celotne funkcije merjenja energije.
Standard je bil pripravljen ob upoštevanju dejstva, da se lahko pri nekaterih načinih uporabe funkcije merjena energije izvaja zakonit metrološki nadzor. Ta del zajema vse zadevne metrološke vidike.
Slika 2 prikazuje pretok med funkcionalnimi bloki funkcije merjena energije. Prikazane so samo povezave med funkcionalnimi bloki, ki jih zahteva ta standard.

General Information

Status
Published
Publication Date
05-Oct-2017
ICS
45.060.10 - Tractive stock
Technical Committee
CLC/TC 9X - Electrical and electronic applications for railways
Drafting Committee
CLC/TC 9X/WG 11 - Energy measurement
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
20-Apr-2022
Directive
2008/57/EC - Directive 2008/57/EC of the European Parliament and of the Council of 17 June 2008 on the interoperability of the rail system within the Community (Recast)
2014/32/EU - Directive 2014/32/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of measuring instruments
Mandate
M/453 - Standardisation mandate addressed to CEN, CENELEC and ETSI in the field of information and communication technologies to support the interoperability of co-operative for intelligent transport in the european community
M/483 - Mandate for programming and standardisation addressed to the European standardisation bodies under directive 2008/57/EC in the field of the interoperability of the rail system within the European Union
Ref Project
SIST EN 50463-2:2018 - Railway applications - Energy measurement on board trains - Part 2: Energy measuring

Relations

Replaces
EN 50463-2:2012 - Railway applications - Energy measurement on board trains - Part 2: Energy measuring
Effective Date
30-Jun-2015
Amended By
EN 50463-2:2017/FprA1:2024 - Railway applications - Energy measurement on board trains - Part 2: Energy measuring
Effective Date
26-Apr-2022
Corrected By
EN 50463-2:2017/AC:2018-10 - Railway applications - Energy measurement on board trains - Part 2: Energy measuring
Effective Date
22-May-2018

Buy Standard

EN 50463-2:2018 - BARVEEN 50463-2:2018 - BARVE
PreviousNext
Standard
EN 50463-2:2018 - BARVE
English language
93 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 50463-2:2018
01-januar-2018
1DGRPHãþD
SIST EN 50463-2:2013
Železniške naprave - Merjenje energije na vlaku - 2. del: Merjenje energije
Railway applications - Energy measurement on board trains - Part 2: Energy measuring
Bahnanwendungen - Energiemessung auf Bahnfahrzeugen - Teil 2: Energiemessung
Applications ferroviaires - Mesure d'énergie à bord des trains - Partie 2 : Mesure
d'énergie
Ta slovenski standard je istoveten z: EN 50463-2:2017
ICS:
45.060.10 9OHþQDYR]LOD Tractive stock
SIST EN 50463-2:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 50463-2:2018

---------------------- Page: 2 ----------------------

SIST EN 50463-2:2018

EUROPEAN STANDARD EN 50463-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2017
ICS 45.060.10 Supersedes EN 50463-2:2012
English Version
Railway applications - Energy measurement on board trains -
Part 2: Energy measuring
Applications ferroviaires - Mesure d'énergie à bord des Bahnanwendungen - Energiemessung auf Bahnfahrzeugen
trains - Partie 2 : Mesure d'énergie - Teil 2: Energiemessung
This European Standard was approved by CENELEC on 2017-05-08. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.



European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
 Ref. No. EN 50463-2:2017 E

---------------------- Page: 3 ----------------------

SIST EN 50463-2:2018
EN 50463-2:2017 (E)
Contents Page
European foreword . 7
Introduction . 8
1 Scope .11
2 Normative references .12
3 Terms, definitions, abbreviations and symbols .13
3.1 Terms and definitions .13
3.2 Abbreviations .16
3.3 Symbols .17
4 Requirements .17
4.1 General .17
4.2 Energy Measurement Function (EMF) .18
4.2.1 General .18
4.2.2 Electrical requirements .18
4.2.3 Accuracy requirements .19
4.2.4 Traction system change .21
4.2.5 Re-verification .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CLC
EN 50317:2012/A1:2022(Amendment)
Railway applications - Current collection systems - Requirements for and validation of measurements of the dynamic interaction between pantograph and overhead contact line
SIST EN 50317:2012/A1:2022

This European Standard specifies the functional requirements for output and accuracy of measurements of the dynamic interaction between pantograph and overhead contact line.

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
CLC/TS 50238-3:2022(Main)
Railway applications - Compatibility between rolling stock and train detection systems - Part 3: Compatibility with axle counters
SIST-TS CLC/TS 50238-3:2022

For the purpose of demonstrating compatibility between rolling stock and axle counter detectors, this document defines the interference limits and evaluation methods to verify rolling stock emissions. Wheel sensors and crossing loops are not covered by this document. This document gives recommended individual limits to be applied to establish compatibility between RST and all selected types of axle counter detectors, including any covered by national standards. The list of selected types of axle counters and their limits for compatibility are drawn on the basis of established performance criteria. It is expected that the trend for newly signalled interoperable lines will be fitted with types that meet the compatibility limits published in the TSI CCS Interfaces Document (ERA/ERTMS/033281). To ensure adequate operational availability, it is essential that the rolling stock complies with the defined limits; otherwise, the established availability of the valid output function of axle counter detectors may be compromised. NOTE The influences from metal parts or inductively coupled resonant circuits on the vehicle, eddy current brakes or magnetic brakes, are not covered by this document but are considered on the basis of national technical specifications. For wheel sensors and wheel detectors in other applications than axle counters but utilizing the same rail sensors and detectors, transient and continuous interference can be considered as equivalent to axle counter detectors or axle counter sensors.

  • Technical specification
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50702:2021(Main)
Railway applications - Rolling stock - Conductor rail current collectors (shoegear): Characteristics and tests
SIST EN 50702:2021

This document specifies the tests for the current collectors to enable current collection from the third or fourth rail system as well as associated fuses and short circuit devices. It also specifies the general assembly characteristics to be applied to current collectors. This document is applicable to all types of vehicles with third or fourth rail current collectors. This document does not apply to roof mounted pantographs.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
CLC/TS 50238-2:2020(Main)
Railway applications - Compatibility between rolling stock and train detection systems - Part 2: Compatibility with track circuits
SIST-TS CLC/TS 50238-2:2020

This document defines, for the purpose of ensuring compatibility between rolling stock and track circuits, the limits for interference current emissions from rolling stock. The measurement and evaluation methods for verifying conformity of rolling stock to these limits are presented in a dedicated annex. The interference limits are only applicable to rolling stock that is intended to run on lines exclusively equipped with preferred track circuits listed in this document. The rolling stock test methodology (infrastructure conditions, test configurations, operational conditions, etc.) presented in this document is applicable to establish compatibility with any track circuits. This document gives guidance on the derivation of interference current limits specified for rolling stock and defines measurement methods and evaluation criteria in a dedicated annex. This document defines: a) a set of interference current limits for RST (Rolling Stock) applicable for each of the following types of traction system: 1) DC (750 V, 1,5 kV and 3 kV); 2) 16,7 Hz AC; 3) 50 Hz AC; b) methodology for the demonstration of compatibility between rolling stock and track circuits; c) measurement method to verify interference current limits and evaluation criteria. NOTE 1 The basic parameters of track circuits associated with the interference current limits for RST are not in the scope of this document. NOTE 2 Any phenomena linked to traction power supply and associated protection (over voltage, short-circuit current, under- and over-voltage if regenerative brakes are used) is part of the track circuit design and outside the scope of this document.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50238-1:2019(Main)
Railway applications - Compatibility between rolling stock and train detection systems - Part 1: General
SIST EN 50238-1:2021

This document describes a process to demonstrate compatibility between Rolling Stock (RST) and Train Detection Systems (TDS). It describes the characterization of train detection systems, rolling stock and traction power supply systems. It is worth noting that the demonstration of technical compatibility between the rolling stock and infrastructure with respect to physical dimensions is not detailed in this document. This document is not generally applicable to those combinations of rolling stock, traction power supply and train detection system which were accepted as compatible prior to the issue of this document. However, as far as is reasonably practicable, this document can be applied to modifications of rolling stock, traction power supply or train detection systems which may affect compatibility. The detailed process can be used where no rules and processes for compatibility are established.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50591:2019(Main)
Railway Applications - Rolling Stock - Specification and verification of energy consumption
SIST EN 50591:2020

The purpose of this document is to support rolling stock procurement, especially life cycle cost (LCC) assessment. This document is applicable to the specification and verification of energy consumption of railway rolling stock. It establishes a criterion for the energy consumption of rolling stock to calculate the total net energy consumed, either at current collector or from the fuel tank, over a predefined service profile, to ensure that the results are directly comparable or representative of the real operation of the train. For this purpose, this document considers the energy consumed and regenerated by the rolling stock. The determination methods covered are the simulation and the measurement. This document provides the framework that gives guidance on the generation of comparable energy performance values for trains and locomotives on a common basis and thereby supports benchmarking and improvement of the energy efficiency of rail vehicles. This document does not cover the comparison of energy consumption with other modes of transportation, or even for comparison between diesel and electric traction, covering only the energy consumption of the railway rolling stock itself.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50463-2:2017/AC:2018-10(Corrigendum)
Railway applications - Energy measurement on board trains - Part 2: Energy measuring
SIST EN 50463-2:2018/AC:2020

TC - Engllish version only; editorial corrections in 4.3.3.4, C.4.5 and E.2.

  • Corrigendum
    1 page
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50239:2018(Main)
Railway applications - Radio remote control system of traction vehicle for shunting application
SIST EN 50239:2018

This European Standard contains the application requirements relevant to the radio remote control of a traction unit for shunting application, operated by personnel not physically located at the controls within the vehicle cab. Requirements specification for radio means and wireless protocols, as well as requirements specification for wireless communication between elements of the train, are not covered by this standard. This European Standard is applicable to newly manufactured vehicles and retrofitted vehicles.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50463-3:2017(Main)
Railway applications - Energy measurement on board trains - Part 3: Data handling
SIST EN 50463-3:2018

This European Standard covers the requirements applicable to the Data Handling System (DHS) of an Energy Measurement System (EMS). This document also includes the basic requirements for the Data Collecting System (DCS) on-ground, relating to the acquisition and storage and export of Compiled Energy Billing Data (CEBD). The Conformity Assessment arrangements for the DHS and the DCS are specified in this document. The settlement system is outside the scope of this standard, and the specification of the interface between DCS and settlement system is outside the scope of this standard.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CLC
EN 50463-1:2017(Main)
Railway applications - Energy measurement on board trains - Part 1: General
SIST EN 50463-1:2018

This European Standard describes the primary purpose of the EMS, which is to meter energy consumption for billing and provide compiled energy billing data (CEBD) to a DCS. The EMS may also be used for other functions such as energy management. In addition, this European Standard also describes the primary purpose of a DCS and its interactions with an EMS and settlement system. This part of EN 50463: - gives requirements for the complete Energy Measurement System and also requirements for all devices implementing one or more functions of the Energy Measurement System; - applies to newly manufactured Energy Measurement Systems for use on board railway traction units, powered by AC. and/or DC. supply voltages as listed in EN 50163; - does not apply to portable Energy Measurement Systems.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day