Electric and optical fibre cables - Test methods for non-metallic materials - Part 508: Mechanical tests - Pressure test at high temperature for insulation and sheaths

IEC 60811-508:2012 gives the procedure for a pressure test at high temperature, which typically applies to thermoplastic compounds used for insulating and sheathing materials. IEC 60811-508:2012 cancels and replaces Clause 8 of IEC 60811-3-1:1985, which is withdrawn. Full details of the replacements are shown in Annex A of IEC 60811-100:2012. Significant technical changes with respect to the previous edition are as follows: - re-statement of oven characteristics, especially relating to anti-vibration and to temperature control; - enhanced detail as to the preparations and testing of flat cables; - enhanced detail as to thickness and dimensional measurements. See also the Foreword to IEC 60811-100:2012. This publication is to be read in conjunction with IEC 60811-100:2012.

Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene Werkstoffe - Teil 508: Mechanische Prüfungen - Wärmedruckprüfungen für Isolierhüllen und Mäntel

Câbles électriques et à fibres optiques - Méthodes d'essai pour les matériaux non-métalliques - Partie 508: Essais mécaniques - Essai de pression à température élevée pour enveloppes isolantes et les gaines

La CEI 60811-508:2012 décrit la procédure à suivre pour réaliser l'essai de pression à température élevée, généralement applicable aux mélanges thermoplastiques utilisés pour les matériaux d'isolation et de gainage. La CEI 60811-508:2012 annule et remplace l'Article 8 de la CEI 60811-3-1:1985, qui est supprimée. L'ensemble des détails relatifs aux remplacements figure dans l'Annexe A de la CEI 60811-100:2012. Des modifications techniques importantes ont été effectuées par rapport à l'édition précédente, comme suit: - redéfinition des caractéristiques relatives à l'étuve, en particulier les caractéristiques antivibratoires et le contrôle de la température; - des détails supplémentaires relatifs aux préparations et aux essais de câbles méplats; - des détails supplémentaires relatifs aux mesures d'épaisseur et de dimensions. Voir également l'avant-propos de la CEI 60811-100:2012. Cette publication doit être lue conjointement avec la CEI 60811-100:2012.

Električni in optični kabli - Preskuševalne metode za nekovinske materiale - 508. del: Mehanski preskusi - Tlačni preskus izolacije in plaščev pri visoki temperaturi

508. del standarda IEC 60811 navaja postopek za tlačni preskus pri visoki temperaturi, ki se običajno uporablja za termoplastične zmesi za izolacije in plašče.

General Information

Status
Published
Publication Date
14-Jun-2012
Technical Committee
Drafting Committee
Parallel Committee
Current Stage
6060 - Document made available - Publishing
Start Date
15-Jun-2012
Completion Date
15-Jun-2012

Relations

Buy Standard

Standard
EN 60811-508:2012
English language
21 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2012
(OHNWULþQLLQRSWLþQLNDEOL3UHVNXãHYDOQHPHWRGH]DQHNRYLQVNHPDWHULDOH
GHO0HKDQVNLSUHVNXVL7ODþQLSUHVNXVL]RODFLMHLQSODãþHYSULYLVRNLWHPSHUDWXUL
Electric and optical fibre cables - Test methods for non-metallic materials - Part 508:
Mechanical tests - Pressure test at high temperature for insulation and sheaths
Kabel, isolierte Leitungen und Glasfaserkabel - Prüfverfahren für nichtmetallene
Werkstoffe - Teil 508: Mechanische Prüfungen - Wärmedruckprüfungen für Isolierhüllen
und Mäntel
Câbles électriques et câbles à fibres optiques - Méthodes d'essai pour les matériaux non
-métalliques - Partie 508: Essais mécaniques - Essai de pression à température élevée
pour enveloppes isolantes et gaines
Ta slovenski standard je istoveten z: EN 60811-508:2012
ICS:
29.035.01 Izolacijski materiali na Insulating materials in
splošno general
29.060.20 Kabli Cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 60811-508
NORME EUROPÉENNE
June 2012
EUROPÄISCHE NORM
ICS 29.035.01; 29.060.20 Supersedes EN 60811-3-1:1995 (partially) + A1:1996 (partially) + A2:2001 (partially)

English version
Electric and optical fibre cables -
Test methods for non-metallic materials -
Part 508: Mechanical tests -
Pressure test at high temperature for insulation and sheaths
(IEC 60811-508:2012)
Câbles électriques et à fibres optiques -  Kabel, isolierte Leitungen
Méthodes d'essai pour les matériaux und Glasfaserkabel -
non-métalliques - Prüfverfahren für nichtmetallene
Partie 508: Essais mécaniques - Werkstoffe -
Essai de pression à température élevée Teil 508: Mechanische Prüfungen -
pour enveloppes isolantes et les gaines Wärmedruckprüfungen für Isolierhüllen
(CEI 60811-508:2012) und Mäntel
(IEC 60811-508:2012)
This European Standard was approved by CENELEC on 2012-04-17. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels

© 2012 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60811-508:2012 E
Foreword
The text of document 20/1304/FDIS, future edition 1 of IEC 60811-508, prepared by IEC/TC 20
"Electric cables" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
(dop) 2013-01-17
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2015-04-17

standards conflicting with the
document have to be withdrawn
This document supersedes Clause 8 of EN 60811-3-1:1995 + A1:1996 + A2:2001 (partially). Full
details of the replacements are shown in Annex A of EN 60811-100:2012.

Significant technical changes with respect to EN 60811-3-1:1995 are as follows:

- re-statement of oven characteristics, especially relating to anti-vibration and to temperature control;
- enhanced detail as to the preparations and testing of flat cables;
- enhanced detail as to thickness and dimensional measurements.

See also the Foreword to EN 60811-100:2012.

This standard is to be read in conjunction with EN 60811-100.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
This standard covers the Principle Elements of the Safety Objectives for Electrical Equipment
Designed for Use within Certain Voltage Limits (LVD - 2006/95/EC).

Endorsement notice
The text of the International Standard IEC 60811-508:2012 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60811-3-1:1985 NOTE Harmonized as EN 60811-3-1:1995 (not modified).
IEC 60811-203 NOTE Harmonized as EN 60811-203.
IEC 60811-401 NOTE Harmonized as EN 60811-401.
IEC 60811-501:2012 NOTE Harmonized as EN 60811-501:2012 (not modified).

- 3 - EN 60811-508:2012
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60811-100 2012 Electric and optical fibre cables - Test EN 60811-100 2012
methods for non-metallic materials -
Part 100: General
IEC 60811-201 - Electric and optical fibre cables - Test EN 60811-201 -
methods for non-metallic materials -
Part 201: General tests - Measurement of
insulation thickness
IEC 60811-202 - Electric and optical fibre cables - Test EN 60811-202 -
methods for non-metallic materials -
Part 202: General tests - Measurement of
thickness of non-metallic sheath

IEC 60811-508 ®
Edition 1.0 2012-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Electric and optical fibre cables – Test methods for non-metallic materials –

Part 508: Mechanical tests – Pressure test at high temperature for insulation

and sheaths
Câbles électriques et à fibres optiques – Méthodes d’essai pour les matériaux

non-métalliques –
Partie 508: Essais mécaniques – Essai de pression à température élevée pour

les enveloppes isolantes et les gaines

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
CODE PRIX R
ICS 29.035.01; 29.060.20 ISBN 978-2-88912-984-3

– 2 – 60811-508  IEC:2012
CONTENTS
FOREWORD . 3
INTRODUCTION . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Test method . 6
4.1 General . 6
4.2 Apparatus . 6
4.2.1 Air oven . 6
4.2.2 Indentation device . 7
4.3 Insulation . 7
4.3.1 Sample and test piece preparation . 7
4.3.2 Procedure . 7
4.4 Sheath . 9
4.4.1 Sample and test piece preparation for sheaths . 9
4.4.2 Procedure . 10
5 Test report. 11
Annex A (normative) Calculation of the compressing force . 15
Annex B (informative) Recommended performance requirement . 17
Bibliography . 18

Figure 1 – Indentation device . 12
Figure 2 – Measurement of indentation . 12
Figure 3 – Measurement of indentation for small test pieces . 13
Figure 4 – Flat cable with a flat smaller side . 13
Figure 5 – Indentation device for flat cables with a flat smaller side . 14

Table A.1 – General value for k . 15

60811-508  IEC:2012 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ELECTRIC AND OPTICAL FIBRE CABLES –
TEST METHODS FOR NON-METALLIC MATERIALS –

Part 508: Mechanical tests –
Pressure test at high temperature for insulation and sheaths

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) At
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.