EN 60384-22-1:2004

SLOVENSKI SIST EN 60384-22-1:2005

STANDARD
december 2005
Pritrjeni kondenzatorji za uporabo v elektronski opremi – 22-1. del: Okvirna
podrobna specifikacija: pritrjeni večplastni kondenzatorji za površinsko
namestitev s keramičnim dielektrikom, razred 2 – Raven ocenjevanja EZ (IEC
60384-22-1:2004 + popravek 2004)
Fixed capacitors for use in electronic equipment – Part 22-1: Blank detail
specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class
2 – Assessment level EZ (IEC 60384-22-1:2004 + corrigendum 2004)
ICS 31.060.10 Referenčna številka
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

EUROPEAN STANDARD EN 60384-22-1
NORME EUROPÉENNE
EUROPÄISCHE NORM November 2004

ICS 31.060.10 Partially supersedes EN 132101:1996

English version
Fixed capacitors for use in electronic equipment
Part 22-1: Blank detail specification:
Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2 –
Assessment level EZ
(IEC 60384-22-1:2004 + corrigendum 2004)

Condensateurs fixes utilisés dans  Festkondensatoren zur Verwendung
les équipements électroniques in Geräten der Elektronik
Partie 22-1: Spécification particulière Teil 22-1: Vordruck für Bauartspezifikation:
cadre: Condensateurs multicouches Oberflächenmontierbare
fixes pour montage en surface pour Vielschichtkeramik-Festkondensatoren,
diélectriques en céramique, classe 2 – Klasse 2 –
Niveau d'évaluation EZ Bewertungsstufe EZ
(CEI 60384-22-1:2004 + corrigendum (IEC 60384-22-1:2004 + corrigendum
2004) 2004)
This European Standard was approved by CENELEC on 2004-09-01. CENELEC members are bound to
comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and
notified to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels

© 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

Ref. No. EN 60384-22-1:2004 E
Foreword
The text of document 40/1423/FDIS, future edition 1 of IEC 60384-22-1, prepared by IEC TC 40,
Capacitors and resistors for electronic equipment, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as EN 60384-22-1 on 2004-09-01.
This European Standard, together with EN 60384-21-1:2004, supersedes EN 132101:1996.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2005-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2007-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60384-22-1:2004 + corrigendum September 2004 was
approved by CENELEC as a European Standard without any modification.
__________
- 3 - EN 60384-22-1:2004
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE Where an international publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
Publication Year Title EN/HD Year
IEC 60384-1 1999 Fixed capacitors for use in electronic EN 60384-1 2001
(mod) equipment
Part 1: Generic specification
IEC 60384-22 2004 Part 22: Sectional specification: Fixed EN 60384-22 2004
+ corr. September 2004 surface mount multilayer capacitors of
ceramic dielectric, Class 2
IEC 60410 1973 Sampling plans and procedures for - -
inspection by attributes
INTERNATIONAL
IEC
STANDARD 60384-22-1
First edition
2004-06
Fixed capacitors for use in electronic equipment –
Part 22-1:
Blank detail specification:
Fixed surface mount multilayer capacitors
of ceramic dielectric, Class 2 –
Assessment level EZ
© IEC 2004 ⎯ Copyright - all rights reserved
No part of this publication may be reproduced or utilized in any form or by any means, electronic or
mechanical, including photocopying and microfilm, without permission in writing from the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
PRICE CODE
Commission Electrotechnique Internationale P
International Electrotechnical Commission
ɆɟɠɞɭɧɚɪɨɞɧɚɹɗɥɟɤɬɪɨɬɟɯɧɢɱɟɫɤɚɹɄɨɦɢɫɫɢɹ
For price, see current catalogue

– 2 – 60384-22-1 © IEC:2004(E)
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 General data .7
1.1 Recommended method(s) of mounting (to be inserted).7
1.2 Dimensions .7
1.3 Ratings and characteristics .7
1.4 Normative references .8
1.5 Marking .8
1.6 Ordering information.8
1.7 Certified records of released lots.8
1.8 Additional information (not for inspection purposes) .8
1.9 Additional or increased severities or requirements to those specified in the
generic and/or sectional specification .8
2 Inspection requirements .9
2.1 Procedures.9
Table 1 – Case size reference and dimensions .7
Table 2 – Values of capacitance and of voltage related to case sizes .7
Table 3 – Other characteristics .8
Table 4 – Test schedule for quality conformance inspection.9

60384-22-1 © IEC:2004(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 22-1: Blank detail specification:
Fixed surface mount multilayer capacitors
of ceramic dielectric, Class 2 –
Assessment level EZ
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60384-22-1 has been prepared by IEC technical committee 40:
Capacitors and resistors for electronic equipment
This standard and its related publications (CEI 60384-21, IEC 60384-21-1 and IEC 60384-22)
cancel and replace IEC 60384-10 (1989) and its Amendments 1 (1993) and 2 (2000) as well
as IEC 60384-10-1 (1989) and its Amendment 1 (1993).
The text of this standard is based on the following documents:
FDIS Report on voting
40/1423/FDIS 40/1454/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

– 4 – 60384-22-1 © IEC:2004(E)
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed;
• withdrawn;
• replaced by a revised edition, or
• amended.
A bilingual version of this standard may be issued at a later date.
The contents of the corrigendum of September 2004 have been included in this copy.

60384-22-1 © IEC:2004(E) – 5 –
INTRODUCTION
Blank detail specification
A blank detail specification is a supplementary document to the sectional specification and
contains requirements for style, layout and minimum content of detail specifications. Detail
specifications not complying with these requirements may not be considered as being in
accordance with IEC specifications nor shall they so be described.
In the preparation of detail specifications the content of 1.4 of the sectional specification shall
be taken into account.
The numbers between square brackets on the first page of the detail specification correspond
to the following information which shall be inserted in the position indicated.
Identification of the detail specification
(1) The “International Electrotechnical Commission” or the National Standards
Organization under whose authority the detail specification is drafted.
(2) The IEC or National Standards number of the detail specification, date of issue and
any further information required by the national system.
(3) The number and issue number of the IEC or national generic specification.
(4) The IEC number of the blank detail specification.
Identification of the capacitor
(5) A short description of the type of capacitor.
(6) Information on typical construction (when applicable).
(7) Outline drawing with main dimensions which are of importance for interchangeability
and/or reference to the national or international documents for outlines. Alternatively,
this drawing may be given in an annex to the detail specification.
(8) Application or group of applications covered and/or assessment level.
(9) Reference data on the most important properties,
...