Fibre optic interconnecting devices and passive components - Performance standard - Part 121-2: Simplex and duplex cords with single-mode fibre and cylindrical ferrule connectors for category C - Controlled environment

IEC 61753-121-2:2010(E) specifies the test requirements for finished cable assemblies for use as patchcords, work area cords and equipment cords for applications in a controlled (C) environment according to IEC 61753-1, where the connectors already comply, with the Category C requirements of IEC 61753-1. The assemblies consist of simplex or duplex fibre optic cable terminated at each end of the cable with non-angled (PC) or angled (APC) polished single-mode fibre optic connectors with cylindrical ferrules. The wavelength of operation is between 1 260 nm and 1 625 nm.

Lichtwellenleiter - Verbindungselemente und passive Bauteile -Betriebsverhalten - Teil 121-2: Simplex- und Duplexkabel mit Einmoden-Lichtwellenleiter-Steckverbindern mit zylindrischen Ferrulen für die Kategorie C - Kontrollierte Umgebung

Dispositifs d’interconnexion et composants passifs fibroniques - Norme de performance - Partie 121-2: Cordons simplex et duplex avec fibres unimodales, munis de connecteurs à férule cylindrique pour catégorie C - Environnement contrôlé

La CEI 61753-121-2:2010 spécifie les exigences relatives aux essais appliqués aux cordons finis utilisés en tant que cordons de brassage, cordons de zone de travail et cordons d'équipement, en vue d'applications dans un environnement contrôlé (C) conformément à la CEI 61753-1, là où les connecteurs sont déjà conformes, conjointement avec les exigences de la catégorie C de la CEI 61753-1. Les ensembles sont constitués de câbles à fibres optiques simplex ou duplex munis à chaque extrémité du câble de connecteurs à fibres optiques unimodales polies sans angle (PC) ou à angle (APC), comportant des férules cylindriques. La longueur d'onde de fonctionnement est comprise entre 1 260 nm et 1 625 nm.

Optični spojni elementi in pasivne komponente - Tehnični standardi - 121-2. del: Simpleksne in dupleksne vrvice z enorodnim optičnim vlaknom ter cilindričnimi tulčastimi konektorji za kategorijo C - Nadzorovano okolje (IEC 61753-121-2:2017)

Standard IEC 61753-121-2:2010(E) določa preskusne zahteve za dokončane kabelske sklope, ki se uporabljajo kot stikalni kabli, kabli na delovnem območju in kabli opreme za uporabo v nadzorovanem (C) območju skladno s standardom IEC 61753-1, pri čemer so konektorji skladni z zahtevami kategorije C standarda IEC 61753-1. Sklopi so sestavljeni iz simpleksnih in dupleksnih optičnih kablov, ki so na vsaki strani zaključeni z nekotnimi (PC) ali kotnimi (APC) enorodnimi optičnimi konektorji s cilindričnimi tulkami. Delovna valovna dolžina je med 1260 nm in 1625 nm.

General Information

Status
Published
Publication Date
19-Oct-2017
Withdrawal Date
19-Oct-2020
Current Stage
6060 - Document made available - Publishing
Start Date
20-Oct-2017
Completion Date
20-Oct-2017

Relations

Buy Standard

Standard
EN 61753-121-2:2018
English language
22 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2018
1DGRPHãþD
SIST EN 61753-121-2:2010
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH7HKQLþQLVWDQGDUGLGHO
6LPSOHNVQHLQGXSOHNVQHYUYLFH]HQRURGQLPRSWLþQLPYODNQRPWHUFLOLQGULþQLPL
WXOþDVWLPLNRQHNWRUML]DNDWHJRULMR&1DG]RURYDQRRNROMH ,(&
Fibre optic interconnecting devices and passive components - Performance standards -
Part 121-2: Simplex and duplex cords with singlemode fibre and cylindrical ferrule
connectors for category C - Controlled environment (IEC 61753-121-2:2017)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil
121-2: Simplex- und Duplexkabel mit Einmoden-Lichtwellenleiter-Steckverbindern mit
zylindrischen Ferrulen für die Kategorie C - Kontrollierte Umgebung (IEC 61753-121-
2:2017)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Norme de qualité
de fonctionnement - Partie 121-2: Cordons simplex et duplex avec fibres unimodales,
munis de connecteurs à férule cylindrique pour catégorie C - Environnement contrôlé
(IEC 61753-121-2:2017)
Ta slovenski standard je istoveten z: EN 61753-121-2:2017
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 61753-121-2

NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2017
ICS 33.180.20 Supersedes EN 61753-121-2:2010
English Version
Fibre optic interconnecting devices and passive components -
Performance standard - Part 121-2: Simplex and duplex cords
with single-mode fibre and cylindrical ferrule connectors for
category C - Controlled environment
(IEC 61753-121-2:2017)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Norme de performance - Bauteile -Betriebsverhalten - Teil 121-2: Simplex- und
Partie 121-2: Cordons simplex et duplex avec fibres Duplexkabel mit Einmoden-Lichtwellenleiter-
unimodales, munis de connecteurs à férule cylindrique pour Steckverbindern mit zylindrischen Ferrulen für die Kategorie
catégorie C - Environnement contrôlé C - Kontrollierte Umgebung
(IEC 61753-121-2:2017) (IEC 61753-121-2:2017)
This European Standard was approved by CENELEC on 2017-06-27. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61753-121-2:2017 E

European foreword
The text of document 86B/4076/FDIS, future edition 2 of IEC 61753-121-2, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61753-121-2:2017.

The following dates are fixed:
(dop) 2018-04-20
• latest date by which the document has to be
implemented at national level by
publication of an identical national
standard or by endorsement
• latest date by which the national (dow) 2020-10-20
standards conflicting with the
document have to be withdrawn
This document supersedes EN 61753-121-2:2010.

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice
The text of the International Standard IEC 61753-121-2:2017 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60794-1-2:2017 NOTE Harmonized as EN 60794-1-2:2017 (not modified).
IEC 60794-2 NOTE Harmonized as EN 60794-2.
IEC 61300 Series NOTE Harmonized as EN 61300 Series.
IEC 61753 Series NOTE Harmonized as EN 61753 Series.
IEC 61756-1 NOTE Harmonized as EN 61756-1.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1  Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2  Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year

IEC 60793-2-50 -  Optical fibres - EN 60793-2-50 -
Part 2-50: Product specifications -
Sectional specification for class B single-
mode fibres
IEC 60794-2-50 -  Optical fibre cables - EN 60794-2-50 -
Part 2-50: Indoor cables - Family
specification for simplex and duplex cables
for use in terminated cable assemblies
IEC 60794-2-51 -  Optical fibre cables - EN 60794-2-51 -
Part 2-51: Indoor cables - Detail
specification for simplex and duplex cables
for use in cords for controlled environment
IEC 61300-1 -  Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
IEC 61300-2-4 -  Fibre optic interconnecting devices and EN 61300-2-4 -
passive components - Basic test and
measurement procedures -
Part 2-4: Tests - Fibre/cable retention
IEC 61300-2-22 -  Fibre optic interconnecting devices and EN 61300-2-22 -
passive components - Basic test and
measurement procedures -
Part 2-22: Tests - Change of temperature
IEC 61300-2-42 -  Fibre optic interconnecting devices and EN 61300-2-42 -
passive components - Basic test and
measurement procedures - Part 2-42:
Tests - Static side load for strain relief
IEC 61300-2-44 -  Fibre optic interconnecting devices and EN 61300-2-44 -
passive components - Basic test and
measurement procedures -
Part 2-44: Tests - Flexing of the strain relief
of fibre optic devices
Publication Year Title EN/HD Year

IEC 61300-3-1 -  Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements
- Visual examination
IEC 61300-3-3 -  Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -
Part 3-3: Examinations and measurements
- Active monitoring of changes in
attenuation and return loss
IEC 61300-3-6 -  Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures -
Part 3-6: Examinations and measurements
- Return loss
IEC 61300-3-22 -  Fibre optic interconnecting devices and EN 61300-3-22 -
passive components - Basic test and
measurement procedures -
Part 3-22: Examinations and
measurements - Ferrule compression force
IEC 61300-3-25 -  Fibre optic interconnecting devices and EN 61300-3-25 -
passive components - Basic test and
measurement procedures -
Part 3-25: Examinations and
measurements - Concentricity of non-
angled ferrules and non-angled ferrules
with fibre installed
IEC 61300-3-26 -  Fibre optic interconnecting devices and EN 61300-3-26 -
passive components - Basic test and
measurement procedures -
Part 3-26: Examinations and
measurements - Measurement of the
angular misalignment between fibre and
ferrule axes
IEC 61300-3-28 -  Fibre optic interconnecting devices and EN 61300-3-28 -
passive components - Basic test and
measurement procedures -
Part 3-28: Examinations and
measurements - Transient loss
IEC 61300-3-34 -  Fibre optic interconnecting devices and EN 61300-3-34 -
passive components - Basic test and
measurement procedures -
Part 3-34: Examinations and
measurements - Attenuation of random
mated connectors
IEC 61300-3-35 -  Fibre optic interconnecting devices and EN 61300-3-35 -
passive components - Basic test and
measurement procedures -
Part 3-35: Examinations and
measurements - Visual inspection of fibre
optic connectors and fibre-stub
transceivers
Publication Year Title EN/HD Year

IEC 61300-3-47 -  Fibre optic interconnecting devices and EN 61300-3-47 -
passive components - Basic test and
measurement procedures -
Part 3-47: Examinations and
measurements - Endface geometry of
PC/APC spherically polished ferrules using
interferometry
IEC 61753-1 -  Fibre optic interconnecting devices and EN 61753-1 -
passive components performance standard
- Part 1: General and guidance for
performance standards
IEC 61753-021-2 -  Fibre optic interconnecting devices and EN 61753-021-2 -
passive components performance standard
- Part 021-2: Grade C/3 single-mode fibre
optic connectors for category C -
Controlled environment
IEC 61754 Series Fibre optic interconnecting devices and EN 61754 Series
passive components - Fibre optic
connector interfaces
IEC 61755 Series Fibre optic interconnecting devices and EN 61755 Series
passive components - connector optical
interfaces
IEC/TR 61931 -  Fibre optic - Terminology - -

IEC 61753-121-2 ®
Edition 2.0 2017-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Performance

standard –
Part 121-2: Simplex and duplex cords with single-mode fibre and cylindrical

ferrule connectors for category C – Controlled environment

Dispositifs d’interconnexion et composants passifs fibroniques – Norme de

performance –
Partie 121-2: Cordons simplex et duplex avec fibres unimodales, munis de

connecteurs à férule cylindrique pour catégorie C – Environnement contrôlé

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-4390-9

– 2 – IEC 61753-121-2:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 7
4 Description . 8
4.1 General . 8
4.2 Optical fibres . 8
4.3 Cable design and construction . 8
4.4 Optical connectors . 8
4.4.1 Mechanical connectivity . 8
4.4.2 Optical performance requirements . 8
4.4.3 Connector set performance requirements . 8
4.5 Cable bend radius . 8
5 Tests . 8
5.1 General . 8
5.2 Measurement wavelengths . 9
5.3 Device under test . 9
5.4 Test report .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.