Electric motor-operated tools - Dust measurement Procedure - Part 1: General requirements

This European Standard specifies general requirements for the dust measurement of electric motor-operated tools supplied from mains or from batteries. This European Standard applies to those tools with and without dust extraction unit where dust such as mineral dust containing silica or wood dust is expected.

Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 1: Allgemeine Anforderungen

Outils électriques à moteur - Procédure de mesure de la poussière - Partie 1: Exigences générales

Elektromotorna orodja - Postopek meritve prahu - 1. del: Splošne zahteve - Dopolnilo A1

General Information

Status
Published
Publication Date
25-Apr-2019
Withdrawal Date
14-Jan-2022
Current Stage
6060 - Document made available - Publishing
Start Date
26-Apr-2019
Due Date
20-Sep-2020
Completion Date
26-Apr-2019

Relations

Buy Standard

Amendment
EN 50632-1:2015/A1:2019
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2019
Elektromotorna orodja - Postopek meritve prahu - 1. del: Splošne zahteve -
Dopolnilo A1
Electric motor-operated tools - Dust measurement Procedure - Part 1: General
requirements
Motorbetriebene Elektrowerkzeuge - Staubmessverfahren - Teil 1: Allgemeine
Anforderungen
Outils électriques à moteur - Procédure de mesure de la poussière - Partie 1: Exigences
générales
Ta slovenski standard je istoveten z: EN 50632-1:2015/A1:2019
ICS:
25.140.20 Električna orodja Electric tools
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 50632-1:2015/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2019
ICS 25.140.20
English Version
Electric motor-operated tools - Dust measurement Procedure -
Part 1: General requirements
Outils électriques à moteur - Procédure de mesure de la Motorbetriebene Elektrowerkzeuge - Staubmessverfahren -
poussière - Partie 1: Exigences générales Teil 1: Allgemeine Anforderungen
This amendment A1 modifies the European Standard EN 50632-1:2015; it was approved by CENELEC on 2019-01-15. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 50632-1:2015/A1:2019 E

Contents
European foreword . 3
1 Modification to 4.1 . 4
2 Modification to 4.2 . 4
3 Modification to 4.3 . 4
4 Additional subclause 4.4 . 5
5 Modification to 5.1 . 5
6 Modification to Clause 6 . 6

European foreword
This document (EN 50632-1:2015/A1:2019) has been prepared by CLC/TC 116 “Safety of motor-
operated electric tools”.
This amendment was developed to include modifications suggested by practical tests.
The following dates are fixed:
• latest date by which the amendment has to be implemented (dop) 2020-01-15
at national level by publication of an identical
national standard or by endorsement
• latest date by which the national standards conflicting (dow) 2022-01-15
with the amendment have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.