EN ISO 19712-2:2013

SLOVENSKI STANDARD
01-februar-2014
3ROLPHUQLPDWHULDOL'HNRUDWLYQLWUGQLSRYUãLQVNLPDWHULDOLGHO8JRWDYOMDQMH
ODVWQRVWL3ORãþH,62
Plastics - Decorative solid surfacing materials - Part 2: Determination of properties -
Sheet goods (ISO 19712-2:2007)
Kunststoffe - Dekorative Mineralwerkstoffe - Teil 2: Prüfverfahren - Plattenware (ISO
19712-2:2007)
Plastiques - Matériaux décoratifs massifs de revêtement de surface - Partie 2:
Détermination des propriétés - Produits en feuilles (ISO 19712-2:2007)
Ta slovenski standard je istoveten z: EN ISO 19712-2:2013
ICS:
83.140.20 /DPLQDWQHSORãþH Laminated sheets
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 19712-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2013
ICS 83.140.20
English Version
Plastics - Decorative solid surfacing materials - Part 2:
Determination of properties - Sheet goods (ISO 19712-2:2007)
Plastiques - Matériaux décoratifs massifs de revêtement de Kunststoffe - Dekorative Mineralwerkstoffe - Teil 2:
surface - Partie 2: Détermination des propriétés - Produits Prüfverfahren - Plattenware (ISO 19712-2:2007)
en feuilles (ISO 19712-2:2007)
This European Standard was approved by CEN on 22 December 2012.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19712-2:2013: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
The text of ISO 19712-2:2007 has been prepared by Technical Committee ISO/TC 61 “Plastics” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 19712-2:2013 by
Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by NBN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by July 2013, and conflicting national standards shall be withdrawn at the
latest by July 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19712-2:2007 has been approved by CEN as a EN ISO 19712-2:2013 without any
modification.
INTERNATIONAL ISO
STANDARD 19712-2
First edition
2007-12-15
Plastics — Decorative solid surfacing
materials —
Part 2:
Determination of properties — Sheet
goods
Plastiques — Matériaux décoratifs massifs de revêtement de surface —
Partie 2: Détermination des propriétés — Produits en feuilles

Reference number
ISO 19712-2:2007(E)
©
ISO 2007
ISO 19712-2:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.

©  ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved

ISO 19712-2:2007(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Cleaning the test specimen surface . 2
5 Surface defects . 3
6 Consistency of colour . 3
7 Load test . 5
8 Resistance to impact by large-diameter ball .7
9 Lightfastness. 10
10 Stain/chemical-resistance test . 15
11 Resistance to cigarette burns . 23
12 Resistance to dry heat. 31
13 Resistance to wet heat . 37
14 Hot/cold-cycle water-resistance test . 40
15 Hardness. 41
16 Ability to be renewed. 41
Bibliography . 42

ISO 19712-2:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 19712-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products.
ISO 19712 consists of the following parts, under the general title Plastics — Decorative solid surfacing
materials:
⎯ Part 1: Classification and specifications
⎯ Part 2: Determination of properties — Sheet goods
⎯ Part 3: Determination of properties — Solid surface shapes
iv © ISO 2007 – All rights reserved

ISO 19712-2:2007(E)
Introduction
This part of ISO 19172 is intended for use by manufacturers, installers and specifiers of solid surfacing
materials.
The test methods and minimum performance values presented have been related as closely as possible to
end-use applications. The fabrication techniques employed may, however, have a bearing on product
performance and service.
The performance requirements include impact resistance, structure, renewability, colourfastness, cleanability,
stain resistance, water resistance, chemical resistance, bacterial and fungal resistance, and other significant
properties.
INTERNATIONAL STANDARD ISO 19712-2:2007(E)

Plastics — Decorative solid surfacing materials —
Part 2:
Determination of properties — Sheet goods
SAFETY STATEMENT — Persons using this document should be familiar with normal laboratory
practice, if applicable. This document does not purport to address all of the safety problems, if any,
associated with its use. It is the responsibility of the user to establish appropriate safety and health
practices and to ensure compliance with any regulatory conditions.
1 Scope
This part of ISO 19712 specifies the methods of test for determination of the properties of solid surfacing
materials, as defined in Clause 3, in the form of sheets. These methods are primarily intended for testing the
materials specified in ISO 19712-1.
The tests may be carried out on finished sheets, but are generally carried out on test specimens of a size
sufficient to meet the requirements of the test, and of the same material and finish as the finished sheet.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour
ISO 105-B02, Textiles — Tests for colour fastness — Part B02: Colour fastness to artificial light: Xenon arc
fading lamp test
ISO 209:2007, Aluminium and aluminium alloys — Chemical composition
ISO 1770, Solid-stem general purpose thermometers
ISO 2039-1, Plastics — Determination of hardness — Part 1: Ball indentation method
ISO 2039-2, Plastics — Determination of hardness — Part 2: Rockwell hardness
ISO 3668, Paints and varnishes — Visual comparison of the colour of paints
ISO 4211:1979, Furniture — Assessment of surface resistance to cold liquids
1)
ISO 4892:1981, Plastics — Methods of exposure to laboratory light sources
ISO 4892-1, Plastics — Methods of exposure to laboratory light sources — Part 1: General guidance

1) Withdrawn, but still used in certain Asian countries.
SIST EN ISO 197
...