EN 13282-3:2015

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Hydraulische Tragschichtbinder - Teil 3: KonformitätsbewertungLiants hydrauliques routiers - Partie 3: Évaluation de la conformitéHydraulic road binders - Part 3: Conformity evaluation93.080.20Materiali za gradnjo cestRoad construction materials91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 13282-3:2015SIST EN 13282-3:2015en,fr,de01-julij-2015SIST EN 13282-3:2015SLOVENSKI
STANDARDSIST EN 13282-3:20131DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13282-3
April 2015 ICS 93.080.20 Supersedes EN 13282-3:2013English Version
Hydraulic road binders - Part 3: Conformity evaluation
Liants hydrauliques routiers - Partie 3: Évaluation de la conformité
Hydraulische Tragschichtbinder - Teil 3: Konformitätsbewertung This European Standard was approved by CEN on 1 February 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2015 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13282-3:2015 ESIST EN 13282-3:2015

Contents Page
Foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Factory production control by the manufacturer . 6 4.1 General requirements . 6 4.1.1 Concept . 6 4.1.2 Work's quality manual . 6 4.1.3 Management systems . 7 4.1.4 System of documentation . 7 4.2 Internal quality control . 7 4.2.1 Process control . 7 4.2.2 Measuring and testing . 8 4.2.3 Handling, storage, packaging and delivery . 8 4.3 Autocontrol testing of samples . 8 4.3.1 Sampling and testing . 8 4.3.2 Evaluation of results of autocontrol testing of samples . 8 4.3.3 Corrective action. 9 4.3.4 Measuring and test equipment for autocontrol testing . 9 4.3.5 Quality records . 9 5 Determination of the product-type . 9 6 Assessment of the factory production control . 10 6.1 Continuous surveillance, assessment and evaluation of factory production control . 10 6.1.1 Inspection tasks . 10 6.1.2 Frequency of inspections . 10 6.1.3 Reports . 10 6.2 Initial inspection of the factory and the factory production control . 10 6.2.1 Inspection of a new factory . 10 6.2.2 Inspection of an existing factory . 10 6.2.3 Criteria for the assessment of the production equipment . 10 6.2.4 Criteria for the activities of the laboratories . 11 6.2.5 Reports . 11 7 Actions in the event of non-conformity . 11 7.1 Actions to be taken by the manufacturer . 11 7.2 Actions to be taken in case of a non-conforming factory production control system . 11 8 Requirement for dispatching centres . 12 8.1 General . 12 8.2 Tasks for the intermediary . 12 8.2.1 Quality control . 12 8.2.2 Confirmation autocontrol testing of samples taken at the dispatching centre . 12 Bibliography . 14
1 Scope This European Standard specifies the scheme for the assessment and verification of constancy of performance of hydraulic road binders and their conformity with the corresponding product specification standards EN 13282-1 and EN 13282-2. This European Standard provides technical rules for factory production control by the manufacturer, including autocontrol testing of samples. It also provides rules for actions to be followed in the event of non-conformity. This European Standard should be linked with Annexes ZA of European Standards covering hydraulic road binders, i.e. EN 13282-1 and EN 13282-2, in particular for the assignments of tasks to the manufacturer and to the production control certification body. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 196-1, Methods of testing cement - Part 1: Determination of strength EN 196-2, Methods of testing cement - Part 2: Chemical analysis of cement EN 196-3, Methods of testing cement - Part 3: Determination of setting times and soundness EN 196-7, Methods of testing cement - Part 7: Methods of taking and preparing samples of cement EN 13282-1, Hydraulic road binders - Part 1: Rapid hardening hydraulic road binders - Composition, specifications and conformity criteria EN 13282-2, Hydraulic road binders - Part 2: Normal hardening hydraulic road binders - Composition, specifications and conformity criteria 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 AVCP abbreviation for assessment and verification of constancy of performance 3.2 certificate of conformity of factory production control document issued under the rules of this scheme for the AVCP indicating that adequate confidence is provided that factory production control is in conformity with the relevant product specification standard 3.3 conformity mark protected mark applied on the basis of the certificate of conformity of the factory production control 3.4 initial period immediate period starting after the first issuing of the certificate of conformity of factory production control for a hydraulic road binder and at the latest from the first dispatching of hydraulic road binder SIST EN 13282-3:2015
...