EN ISO 10424-1:2004
(Main)Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)
Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill stem elements (ISO 10424-1:2004)
ISO 10424-1:2004 specifies requirements for the following drill stem elements: upper and lower kelly valves; square and hexagonal kellys; drill stem subs; standard steel and non-magnetic drill collars; drilling and coring bits.
ISO 10424-1:2004 is not applicable to drill pipe and tool joints, rotary shouldered connection designs, thread gauging practice, or grand master, reference master and working gauges.
Erdöl- und Erdgasindustrie - Drehende Bohrelemente - Teil 1: Anforderungen an drehende Bohrelemente (ISO 10424-1:2004)
Industries du pétrole et du gaz naturel - Equipements de forage rotary - Partie 1: Eléments de forage rotary (ISO 10424-1:2004)
Industrija za predelavo nafte in zemeljskega plina – Oprema za rotacijsko vrtanje - 1. del: Rotacijski elementi vrtalnega drogovja (ISO 10424-1:2004)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2005
Industrija za predelavo nafte in zemeljskega plina – Oprema za rotacijsko vrtanje -
1. del: Rotacijski elementi vrtalnega drogovja (ISO 10424-1:2004)
Petroleum and natural gas industries - Rotary drilling equipment - Part 1: Rotary drill
stem elements (ISO 10424-1:2004)
Erdöl- und Erdgasindustrie - Drehende Bohrelemente - Teil 1: Anforderungen an
drehende Bohrelemente (ISO 10424-1:2004)
Industries du pétrole et du gaz naturel - Equipements de forage rotary - Partie 1:
Eléments de forage rotary (ISO 10424-1:2004)
Ta slovenski standard je istoveten z: EN ISO 10424-1:2004
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10424-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2004
ICS 75.180.10
English version
Petroleum and natural gas industries - Rotary drilling equipment
- Part 1: Rotary drill stem elements (ISO 10424-1:2004)
Industries du pétrole et du gaz naturel - Equipements de
forage rotary - Partie 1: Eléments de forage rotary (ISO
10424-1:2004)
This European Standard was approved by CEN on 2 August 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10424-1:2004: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 10424-1:2004) has been prepared by Technical Committee ISO/TC 67
"Materials, equipment and offshore structures for petroleum and natural gas industries" in
collaboration with Technical Committee CEN/TC 12 "Materials, equipment and offshore
structures for petroleum, petrochemical and natural gas industries", the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by March 2005, and conflicting national
standards shall be withdrawn at the latest by March 2005.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Endorsement notice
The text of ISO 10424-1:2004 has been approved by CEN as EN ISO 10424-1:2004 without any
modifications.
INTERNATIONAL ISO
STANDARD 10424-1
First edition
2004-09-01
Petroleum and natural gas industries —
Rotary drilling equipment —
Part 1:
Rotary drill stem elements
Industries du pétrole et du gaz naturel — Équipements de forage
rotary —
Partie 1: Éléments de forage rotary
Reference number
ISO 10424-1:2004(E)
©
ISO 2004
ISO 10424-1:2004(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2004
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2004 – All rights reserved
ISO 10424-1:2004(E)
Contents Page
Foreword. v
Introduction . vi
1 Scope. 1
2 Conformance . 3
2.1 Units of measurement . 3
2.2 Tables and figures . 3
3 Normative references . 4
4 Terms, definitions, symbols and abbreviated terms. 5
4.1 Terms and definitions. 5
4.2 Symbols and abbreviated terms. 9
5 Upper and lower kelly valves. 10
5.1 General. 10
5.2 Design criteria . 11
5.3 Connections . 13
5.4 Hydrostatic testing. 14
5.5 Documentation and retention of records . 16
5.6 Marking . 16
5.7 Supplementary requirements . 16
6 Square and hexagonal kellys. 17
6.1 Size, type and dimensions . 17
6.2 Dimensional gauging. 17
6.3 Connections . 17
6.4 Square forged kellys. 18
6.5 Mechanical properties . 18
6.6 Non-destructive examination. 19
6.7 Marking . 19
7 Drill-stem subs . 24
7.1 Class and type. 24
7.2 Dimensions for types A and B. 24
7.3 Dimensions for type C (swivel subs) . 25
7.4 Type D (lift sub) dimensions. 26
7.5 Mechanical properties . 26
7.6 Non-destructive examination. 27
7.7 Connection stress-relief features. 27
7.8 Cold working of thread roots. 27
7.9 Gall-resistant treatment of threads and sealing shoulders. 27
7.10 Marking . 27
8 Drill collars. 34
8.1 General. 34
8.2 Standard steel drill collars . 36
8.3 Non-magnetic drill collars. 38
9 Drilling and coring bits. 45
9.1 Roller bits and blade drag bits . 45
9.2 Diamond drilling bits, diamond core bits and polycrystalline diamond compact (PDC) bits. 46
10 Non-destructive examination of bars and tubes . 50
10.1 General. 50
10.2 Certification and qualification of NDE personnel . 50
ISO 10424-1:2004(E)
10.3 Surface defects.50
10.4 Internal defects.52
Annex A (informative) Tables in US Customary Units .54
Bibliography.66
iv © ISO 2004 – All rights reserved
ISO 10424-1:2004(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committee
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.