EN ISO 16122-2:2015

SLOVENSKI STANDARD
01-junij-2015
1DGRPHãþD
SIST EN 13790-1:2004
Kmetijski in gozdarski stroji - Kontrola škropilnikov v uporabi - 2. del: Vodoravni
jamborni škropilniki (ISO 16122-2:2015)
Agricultural and forestry machinery - Inspection of sprayers in use - Part 2: Horizontal
boom sprayers (ISO 16122-2:2015)
Land- und Forstmaschinen - Kontrolle von in Gebrauch befindlichen
Pflanzenschutzgeräten - Teil 2: Geräte mit horizontalem Gestänge (ISO 16122-2:2015)
Matériel agricole et forestier - Contrôle des pulvérisateurs en service - Partie 2:
Pulvérisateurs à rampe horizontale (ISO 16122-2:2015)
Ta slovenski standard je istoveten z: EN ISO 16122-2:2015
ICS:
65.060.40 Oprema za nego rastlin Plant care equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 16122-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2015
ICS 65.060.40 Supersedes EN 13790-1:2003
English Version
Agricultural and forestry machinery - Inspection of sprayers in
use - Part 2: Horizontal boom sprayers (ISO 16122-2:2015)
Matériel agricole et forestier - Contrôle des pulvérisateurs Land- und Forstmaschinen - Kontrolle von in Gebrauch
en service - Partie 2: Pulvérisateurs à rampe horizontale befindlichen Pflanzenschutzgeräten - Teil 2: Geräte mit
(ISO 16122-2:2015) horizontalem Gestänge (ISO 16122-2:2015)
This European Standard was approved by CEN on 13 September 2014.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16122-2:2015 E
worldwide for CEN national Members.

Contents Page
Foreword .3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2009/128/EC .4
Foreword
This document (EN ISO 16122-2:2015) has been prepared by Technical Committee ISO/TC 23 “Tractors and
machinery for agriculture and forestry“ in collaboration with Technical Committee CEN/TC 144 “Tractors and
machinery for agriculture and forestry” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2015, and conflicting national standards shall be
withdrawn at the latest by September 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 13790-1:2003.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16122-2:2015 has been approved by CEN as EN ISO 16122-2:2015 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2009/128/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association to provide one means of conforming to Essential Requirements of
the New Approach Directive 2009/128/EC Sustainable use of pesticides.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
relevant Essential Requirements of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling within the
scope of this standard.
INTERNATIONAL ISO
STANDARD 16122-2
First edition
2015-03-15
Agricultural and forestry
machinery — Inspection of sprayers in
use —
Part 2:
Horizontal boom sprayers
Matériel agricole et forestier — Contrôle des pulvérisateurs en
service —
Partie 2: Pulvérisateurs à rampe horizontale
Reference number
ISO 16122-2:2015(E)
©
ISO 2015
ISO 16122-2:2015(E)
© ISO 2015
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved

ISO 16122-2:2015(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements and method of verification . 2
4.1 Leaks and dripping . 2
4.2 Pump(s) . 2
4.3 Spray mix agitation. 3
4.4 Spray liquid tank . 3
4.5 Measuring systems, controls and regulation systems . 4
4.6 Lines (pipes and hoses) . 6
4.7 Filters . 6
4.8 Spray boom . 6
4.9 Nozzles . 9
4.10 Blower .10
4.11 Spray guns and lances .10
5 Test methods .11
5.1 Test facilities.11
5.2 Spray and agitation pump(s) .11
5.3 Sprayer’s pressure indicators .12
5.4 Flow meters for controlling the volume/hectare rate .13
5.5 System for controlling forward speed .14
5.6 Uniformity of the transverse volume distribution with a horizontal patternator .15
5.7 Flow rate of the spray nozzles .16
5.8 Pressure drop .17
5.9 Pressure variation when the sections are closed .17
5.10 Pressure variation when the spray is switched off .17
5.11 Pressure distribution .17
Bibliography .18
ISO 16122-2:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent ri
...