EN 4612-013:2011
(Main)Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 013: SX, TC and UC - Nickel plated copper - Operating temperatures, between - 65 °C and 150 °C - Single extruded wall for equipment only, with jacket and screen (spiral) - UV laser printable - Product standard
Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 013: SX, TC and UC - Nickel plated copper - Operating temperatures, between - 65 °C and 150 °C - Single extruded wall for equipment only, with jacket and screen (spiral) - UV laser printable - Product standard
This standard specifies the characteristics of UV laser printable jacket, silver plated copper conductor, electrical cables Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE) family for use in the on board electrical systems of aircraft at operating temperatures between - 65 °C and 150 °C, operating at voltages not exceeding 600 V r.m.s and frequencies not exceeding 2 000 Hz. These cables are suitable for airframe use without additional protection. In case of conflict between this standard and other referenced documents the requirements of this standard shall take precedence.
Luft- und Raumfahrt - Ein- und mehradrige elektrische Leitungen zur allgemeinen Verwendung - XLETFE-Familie - ummantelt oder geschirmt und ummantelt - Teil 013: SX, TC und UC - Kupfer vernickelt - Betriebstemperaturen zwischen -65 °C und 150 °C - einfach extrudierte Isolierung nur für Geräteverdrahtung, ummantelt und geschirmt (spiralförmig) - UV-Laser bedruckbar - Produktnorm
Série aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs - Famille XLETFE - Gainés ou blindés et gainés - Partie 013: SX, TC et UC - Cuivre nickelé - Températures de fonctionnement comprises entre – 65 °C et 150 °C - Fil simple isolé pour circuits électriques uniquement, gainé et blindé (guipé) - Marquable au laser UV - Norme de produit
Aeronavtika - Kabli, električni, za splošne namene, eno- in večžilni - Družina XLETFE - Oplaščeni ali zaslonjeni in oplaščeni - 013. del: SX, TC in UC - Ponikljani baker - Obratovalne temperature med -65 °C in 135 °C - Enojno ekstrudirana izolacija samo za opremo, s plaščem in zaslonom (povitje) - Potiskljiva z UV-laserjem - Standard za izdelek
Ta standard določa lastnosti plašča, potiskljivega z UV-laserjem, vodnika iz posrebrenega bakra in električnih kablov iz družine kopolimerov, pridobljenih z mrežno polimerizacijo etilena in tetrafluoretilena (XLETFE), za uporabo v električnih sistemih na krovu letal pri obratovalnih temperaturah med –65 °C in 150 °C, obratovalnih napetostih, ki ne presegajo efektivne vrednosti 600 V, ter frekvencah, ki ne presegajo 2000 Hz. Ti kabli so primerni za uporabo na ogrodjih letal brez dodatne zaščite. V primeru neskladja med tem standardom in drugimi navedenimi dokumenti imajo prednost določila tega standarda.
General Information
- Status
- Published
- Publication Date
- 18-Oct-2011
- Withdrawal Date
- 29-Apr-2012
- Technical Committee
- ASD-STAN - Aerospace
- Drafting Committee
- ASD-STAN/D 2 - Electrical
- Current Stage
- 9093 - Decision to confirm - Review Enquiry
- Start Date
- 01-Jun-2017
- Completion Date
- 28-Jan-2026
Relations
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
- Effective Date
- 28-Jan-2026
Overview
EN 4612-013:2011 is a European standard developed by CEN specifying requirements for aerospace electrical cables from the XLETFE family. These cables feature nickel-plated copper conductors with UV laser printable jackets made from Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE). They are designed for use in aircraft onboard electrical systems, operating under temperatures ranging from -65 °C up to 150 °C, voltages up to 600 V r.m.s, and frequencies below 2,000 Hz. This product standard ensures compatibility, reliability, and safety for avionics wiring assemblies suitable for airframe use without additional protection.
Key Topics
Cable Construction
The cables consist of 1 to 3 nickel-plated copper cores according to EN 4611-009. For multicore cables (2 or 3 cores), twisted construction follows EN 2235 guidelines. The cables include a spiral-wrapped nickel-plated copper stranded woven screen and an XLETFE outer jacket that is UV laser printable, facilitating traceability and identification without compromising cable integrity.Operating Conditions
Designed to operate reliably in extreme environments, these cables support temperatures from -65 °C to 150 °C, suitable for aircraft conditions including thermal shock and cold bend resistance. Electrical ratings include voltages not exceeding 600 V r.m.s and frequency limits up to 2,000 Hz.Performance and Testing
The cables comply with stringent aerospace test methods defined in EN 3475-100, covering visual examination, dimensional stability, ohmic resistance, insulation resistance, accelerated aging, thermal shock, flammability, humidity resistance, mechanical durability, and laser printability for marking permanence.Quality Assurance
Manufacturers must implement aerospace quality management and qualification procedures as per EN 9133, ensuring consistent production and product reliability throughout the cable lifecycle.
Applications
Aircraft Electrical Systems
EN 4612-013 cables are optimized for general-purpose onboard electrical wiring in commercial and military aircraft, including avionics equipment, communication systems, and control circuits.Airframe Wiring
Due to their robust construction, thermal tolerance, and electromagnetic screening, these cables are suitable for airframe use without additional mechanical protection, reducing installation complexity and weight.UV Laser Marking
The UV laser printable jacket enables high-contrast, permanent markings for identification and traceability, critical for maintenance, safety inspections, and compliance with aerospace procedures.
Related Standards
- EN 4611-009 – Defines cores for XLETFE family cables with nickel-plated copper conductors, suitable for high vibration and fluid contaminated environments.
- EN 2235 – Covers construction, testing, and delivery requirements for screened and jacketed single and multicore aerospace cables.
- EN 3475-100 – Specifies test methods applicable to electrical aircraft cables to ensure mechanical, electrical, and environmental performance.
- EN 9133 – Aerospace quality management standard for qualification procedures of standard parts including electrical cables.
- EN 4612-002 – General provisions for XLETFE Family cables, including core and jacket color coding and marking conventions.
By adhering to EN 4612-013:2011, aerospace cable manufacturers and users achieve high reliability, stringent safety, and optimal performance in demanding aircraft environments, supporting modern avionics and airframe wiring needs. This ensures that electrical systems maintain integrity under harsh operational conditions while enabling efficient identification and maintenance protocols through UV laser printable cable jackets.
Get Certified
Connect with accredited certification bodies for this standard
National Aerospace and Defense Contractors Accreditation Program (NADCAP)
Global cooperative program for special process quality in aerospace.
NSF-ISR
NSF International Strategic Registrations.
Orion Registrar Inc.
US-based certification body for management systems.
Sponsored listings
Frequently Asked Questions
EN 4612-013:2011 is a standard published by the European Committee for Standardization (CEN). Its full title is "Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 013: SX, TC and UC - Nickel plated copper - Operating temperatures, between - 65 °C and 150 °C - Single extruded wall for equipment only, with jacket and screen (spiral) - UV laser printable - Product standard". This standard covers: This standard specifies the characteristics of UV laser printable jacket, silver plated copper conductor, electrical cables Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE) family for use in the on board electrical systems of aircraft at operating temperatures between - 65 °C and 150 °C, operating at voltages not exceeding 600 V r.m.s and frequencies not exceeding 2 000 Hz. These cables are suitable for airframe use without additional protection. In case of conflict between this standard and other referenced documents the requirements of this standard shall take precedence.
This standard specifies the characteristics of UV laser printable jacket, silver plated copper conductor, electrical cables Crosslinked Ethylene Tetra Fluoro Ethylene co-polymer (XLETFE) family for use in the on board electrical systems of aircraft at operating temperatures between - 65 °C and 150 °C, operating at voltages not exceeding 600 V r.m.s and frequencies not exceeding 2 000 Hz. These cables are suitable for airframe use without additional protection. In case of conflict between this standard and other referenced documents the requirements of this standard shall take precedence.
EN 4612-013:2011 is classified under the following ICS (International Classification for Standards) categories: 49.060 - Aerospace electric equipment and systems. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 4612-013:2011 has the following relationships with other standards: It is inter standard links to EN 3475-808:2002, EN 3475-408:2025, EN 3475-403:2002, EN 3475-604:2010, EN 3475-508:2007, EN 3475-411:2018, EN 3475-404:2025, EN 3475-418:2019, EN 3475-514:2007, EN 3475-811:2009, EN 3475-306:2005, EN 3475-505:2023, EN 3475-407:2009, EN 3475-307:2005, EN 3475-504:2002. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 4612-013:2011 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WUXGLUDQDLuft- und Raumfahrt - Ein- und mehradrige elektrische Leitungen für allgemeine Verwendung - XLETFE Familie - Mit Mantel oder geschirmt und Mantel - Teil 013: SX, TC und UC - Kupfer vernickelt - Betriebstemperaturen zwischen – 65 °C und 150 °C - Einfach extrudierte Isolierung nur für Geräteverdrahtung, mit Mantel und Schirm (Umseilung) - UV-Laser bedruckbar - ProduktnormSérie aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs - Famille XLETFE - Gainés ou blindés et gainés - Partie 013: SX, TC et UC - Cuivre nickelé - Températures de fonctionnement comprises entre – 65 °C et 150 °C - Fil simple isolé pour circuits électriques uniquement, gainé et blindé (guipé) - Marquable au laser UV - Norme de produitAerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 013: SX, TC and UC - Nickel plated copper - Operating temperatures, between - 65 °C and 150 °C - Single extruded wall for equipment only, with jacket and screen (spiral) - UV laser printable - Product standard49.060Aerospace electric equipment and systemsICS:Ta slovenski standard je istoveten z:EN 4612-013:2011SIST EN 4612-013:2012en,fr01-februar-2012SIST EN 4612-013:2012SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 4612-013
October 2011 ICS 49.060 English Version
Aerospace series - Cables, electrical, for general purpose, single and multicore assembly - XLETFE Family - Jacketed or screened and jacketed - Part 013: SX, TC and UC - Nickel plated copper - Operating temperatures, between - 65 °C and 150 °C - Single extruded wall for equipment only, with jacket and screen (spiral) - UV laser printable - Product standard
Série aérospatiale - Câbles, électriques, d'usage général, mono et multiconducteurs - Famille XLETFE - Gainés ou blindés et gainés - Partie 013: SX, TC et UC - Cuivre nickelé - Températures de fonctionnement comprises entre - 65 °C et 150 °C - Fil simple isolé pour circuits électriques uniquement, gainé et blindé (guipé) - Marquable au laser UV - Norme de produit
Luft- und Raumfahrt - Ein- und mehradrige elektrische Leitungen für allgemeine Verwendung - XLETFE Familie - Mit Mantel oder geschirmt und Mantel - Teil 013: SX, TC und UC - Kupfer vernickelt - Betriebstemperaturen zwischen - 65 °C und 150 °C - Einfach extrudierte Isolierung nur für Geräteverdrahtung, mit Mantel und Schirm (Umseilung) - UV-Laser bedruckbar - ProduktnormThis European Standard was approved by CEN on 20 August 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 4612-013:2011: ESIST EN 4612-013:2012
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...