EN ISO 18275:2018
(Main)Welding consumables - Covered electrodes for manual metal arc welding of high-strength steels - Classification (ISO 18275:2018)
Welding consumables - Covered electrodes for manual metal arc welding of high-strength steels - Classification (ISO 18275:2018)
This document specifies requirements for classification of covered electrodes and deposited metal in the as-welded condition and in the post-weld heat-treated condition for manual metal arc welding of high-strength steels with a minimum yield strength greater than 500 MPa or a minimum tensile strength greater than 570 MPa.
This document is a combined specification providing a classification utilizing a system based on the yield strength and an average impact energy of 47 J of the all-weld metal, or utilizing a system based on the tensile strength and an average impact energy of 27 J of the all-weld metal.
a) Subclauses and tables which carry the suffix letter "A" are applicable only to covered electrodes classified under the system based on the yield strength and an average impact energy of 47 J of the all-weld metal given in this document.
b) Subclauses and tables which carry the suffix letter "B" are applicable only to covered electrodes classified under the system based on the tensile strength and an average impact energy of 27 J of the all-weld metal given in this document.
c) Subclauses and tables which do not have either the suffix letter "A" or the suffix letter "B" are applicable to all covered electrodes classified under this document.
Schweißzusätze - Umhüllte Stabelektroden zum Lichtbogenhandschweißen von hochfesten Stählen - Einteilung (ISO 18275:2018)
Diese Internationale Norm legt die Anforderungen für die Einteilung von umhüllten Stabelektroden und dem aufgetragenen Schweißgut im Schweißzustand und im Zustand nach der Wärmenachbehandlung zum Licht¬bogenhandschweißen von hochfesten Stählen mit einer Mindeststreckgrenze von über 500 MPa oder einer Mindestzugfestigkeit von über 570 MPa fest.
Diese Internationale Norm enthält eine gemeinsame Spezifikation zur Einteilung mit Hilfe eines Systems, das auf der Streckgrenze und einer durchschnittlichen Kerbschlagarbeit von 47 J des reinen Schweißgutes basiert oder mit Hilfe eines Systems, das auf der Zugfestigkeit und einer durchschnittlichen Kerbschlagarbeit von 27 J des reinen Schweißgutes basiert.
a) Unterabschnitte und Tabellen, gekennzeichnet durch ein nachgestelltes „A“, können nur für umhüllte Stabelektroden angewendet werden, die nach der Streckgrenze und einer durchschnittlichen Kerbschlagarbeit von 47 J des reinen Schweißgutes nach dieser Internationalen Norm eingeteilt werden.
b) Unterabschnitte und Tabellen, gekennzeichnet durch ein nachgestelltes „B“, können nur für umhüllte Stabelektroden angewendet werden, die nach der Zugfestigkeit und einer durchschnittlichen Kerbschlagarbeit von 27 J des reinen Schweißgutes nach dieser Internationalen Norm eingeteilt werden.
c) Unterabschnitte und Tabellen, die kein nachgestelltes „A“ oder „B“ enthalten, sind für alle nach dieser Internationalen Norm eingeteilten umhüllten Stabelektroden anwendbar.
Produits consommables pour le soudage - Électrodes enrobées pour le soudage manuel à l'arc des aciers à haute résistance - Classification (ISO 18275:2018)
Le présent document spécifie les exigences relatives à la classification des électrodes enrobées et du métal déposé à l'état brut de soudage ou traité thermiquement après soudage, en soudage manuel à l'arc des aciers à haute résistance ayant une limite d'élasticité minimale supérieure à 500 MPa ou une résistance à la traction minimale supérieure à 570 MPa.
Le présent document fournit une spécification mixte permettant une classification utilisant un système basé soit sur la limite d'élasticité et une énergie de rupture moyenne de 47 J pour le métal fondu hors dilution, soit sur la résistance à la traction et une énergie de rupture moyenne de 27 J pour le métal fondu hors dilution.
a) Les paragraphes et les tableaux qui portent le suffixe «A» sont applicables uniquement aux électrodes enrobées classifiées d'après le système basé sur la limite d'élasticité et une énergie de rupture moyenne de 47 J pour le métal fondu hors dilution donné dans le présent document.
b) Les paragraphes et les tableaux qui portent le suffixe «B» sont applicables uniquement aux électrodes enrobées classifiées d'après le système basé sur la résistance à la traction et une énergie de rupture moyenne de 27 J pour le métal fondu hors dilution donné dans le présent document.
c) Les paragraphes et les tableaux qui ne portent ni le suffixe «A» ni le suffixe «B» sont applicables à toutes les électrodes enrobées classifiées selon le présent document.
Dodajni materiali za varjenje - Oplaščene elektrode za ročno obločno varjenje visokotrdnostnih jekel - Razvrstitev (ISO 18275:2018)
Ta dokument določa zahteve za razvrstitev oplaščenih elektrod ter pretaljene kovine v varjenem stanju in stanju po varjenju s toplotno obdelavo za obločno varjenje visokotrdnih jekel z minimalno mejo prožnosti, večjo od 500 MPa, ali minimalno natezno trdnostjo, večjo od 570 MPa.
Ta dokument je kombinirana specifikacija, ki določa razvrstitev po sistemu na osnovi meje prožnosti in povprečne energije udarca 47 J za čiste vare ali po sistemu na osnovi natezne trdnosti in povprečne energije udarca 27 J za čiste vare.
a) Podtočke in preglednice z dodano črko »A« se uporabljajo samo za oplaščene elektrode, ki so razvrščene po sistemu, ki temelji na meji prožnosti in povprečni energiji udarca 47 J za čiste vare, navedene v tem dokumentu.
b) Podtočke in preglednice z dodano črko »B« se uporabljajo samo za oplaščene elektrode, ki so razvrščene po sistemu, ki temelji na natezni trdnosti in povprečni energiji udarca 27 J za čiste vare, navedene v tem dokumentu.
c) Podtočke in preglednice brez dodane črke »A« ali »B« se uporabljajo za vse elektrode, ki so razvrščene v skladu s tem dokumentom.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2018
1DGRPHãþD
SIST EN ISO 18275:2012
'RGDMQLPDWHULDOL]DYDUMHQMH2SODãþHQHHOHNWURGH]DURþQRREORþQRYDUMHQMH
YLVRNRWUGQRVWQLKMHNHO5D]YUVWLWHY ,62
Welding consumables - Covered electrodes for manual metal arc welding of high-
strength steels - Classification (ISO 18275:2018)
Schweißzusätze - Umhüllte Stabelektroden zum Lichtbogenhandschweißen von
hochfesten Stählen - Einteilung (ISO 18275:2018)
Produits consommables pour le soudage - Électrodes enrobées pour le soudage manuel
à l'arc des aciers à haute résistance - Classification (ISO 18275:2018)
Ta slovenski standard je istoveten z: EN ISO 18275:2018
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 18275
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 25.160.20 Supersedes EN ISO 18275:2012
English Version
Welding consumables - Covered electrodes for manual
metal arc welding of high-strength steels - Classification
(ISO 18275:2018)
Produits consommables pour le soudage - Électrodes Schweißzusätze - Umhüllte Stabelektroden zum
enrobées pour le soudage manuel à l'arc des aciers à Lichtbogenhandschweißen von hochfesten Stählen -
haute résistance - Classification (ISO 18275:2018) Einteilung (ISO 18275:2018)
This European Standard was approved by CEN on 20 September 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 18275:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 18275:2018) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 18275:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 18275:2018 has been approved by CEN as EN ISO 18275:2018 without any modification.
INTERNATIONAL ISO
STANDARD 18275
Third edition
2018-08
Welding consumables — Covered
electrodes for manual metal arc
welding of high-strength steels —
Classification
Produits consommables pour le soudage — Électrodes enrobées
pour le soudage manuel à l'arc des aciers à haute résistance —
Classification
Reference number
ISO 18275:2018(E)
©
ISO 2018
ISO 18275:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 18275:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
4.1 General . 2
4.2 Compulsory and optional sections . 3
5 Symbols and requirements . 3
5.1 Symbol for the product/process . 3
5.2 Symbol for tensile properties of all-weld metal . 3
5.3 Symbol for impact properties of all-weld metal . 4
5.4 Symbol for chemical composition of all-weld metal. 5
5.5 Symbol for type of electrode covering . 7
5.6 Symbol for condition of post-weld heat treatment of all-weld metal . 8
5.7 Symbol for electrode efficiency and type of current . 9
5.8 Symbol for welding position . 9
5.9 Symbol for diffusible hydrogen content of deposited metal . .10
5.10 Mechanical property and composition requirements .10
6 Mechanical property tests .16
6.1 General .16
6.2 Preheating and interpass temperatures .16
6.3 Pass sequence .16
7 Chemical analysis .16
8 Rounding procedure .17
9 Retests .17
10 Technical delivery conditions .17
11 Examples of designation .17
Annex A (informative) Classification systems .20
Annex B (informative) Description of types of electrode covering — Classification by yield
strength and 47 J impact energy .23
Annex C (informative) Description of types of electrode covering — Classification by tensile
strength and 27 J impact energy .24
Annex D (informative) Notes on diffusible hydrogen .26
Annex E (informative) Description of chemical composition symbols — Classification by
yield strength and 47 J impact energy .27
Annex F (informative) Description of chemical composition symbols — Classification by
tensile strength and 27 J impact energy .28
Bibliography .29
ISO 18275:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.