EN 12697-21:2012
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
This European Standard specifies a test method for measuring the indentation of mastic asphalt when it is penetrated at a given temperature, load and for a fixed time period by a standardised cylindrical indentor pin with a circular flat-ended base. This European Standard applies to mastic asphalt with aggregates of maximum nominal size less or equal to 16 mm.
Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an Platten
Die vorliegende Europäische Norm legt ein Prüfverfahren zur Messung der Eindringtiefe in Gussasphalt fest, wenn bei einer festgelegten Temperatur, einer festgelegten Beanspruchung und für eine bestimmte Zeit ein genormter zylindrischer Prüfstempel mit einer kreisrunden flachen Grundfläche in diesen Asphalt eindringt. Diese Europäische Norm gilt für Gussasphalt mit einer maximalen Nennkorngröße gleich oder kleiner als 16 mm.
Mélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 21: Essai d'indentation de plaques
La présente Norme européenne spécifie une méthode d’essai permettant de mesurer l’indentation d’un asphalte coulé lorsqu’il est soumis à la pénétration d’un poinçon normalisé cylindrique à embout plat circulaire, à des valeurs données de température et de charge et pour un temps d’application fixé. Cette Norme européenne s’applique à des asphaltes coulés dont la dimension nominale maximale des granulats est inférieure ou égale à 16 mm.
Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 21. del: Preskus z vtiskanjem na plošče
Ta evropski standard določa preskusno metodo za merjenje vtisa v litem asfaltu, ko se prebada pri določeni temperaturi in bremenu ter v določenem časovnem obdobju s standardiziranim valjastim vtisnim sornikom z okroglo ploščato osnovo. Ta evropski standard se uporablja za liti asfalt z agregati z največjo nominalno velikostjo, ki je manjša ali enaka 16 mm.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an PlattenMélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 21: Essai d'indentation de plaquesBituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-21:2012SIST EN 12697-21:2012en,fr,de01-junij-2012SIST EN 12697-21:2012SLOVENSKI
STANDARDSIST EN 12697-21:2004/AC:2007SIST EN 12697-21:20041DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-21
April 2012 ICS 93.080.20 Supersedes EN 12697-21:2003English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 21: Indentation using plate specimens
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 21: Essai d'indentation de plaques
Asphalt - Prüfverfahren für Heißasphalt - Teil 21: Eindringversuch an Platten This European Standard was approved by CEN on 26 February 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-21:2012: ESIST EN 12697-21:2012
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.