EN 15102:2007

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Decorative wallcoverings - Roll and panel form productsRevêtements muraux décoratifs - Rouleaux et panneauxDekorative Wandbekleidungen - Rollen- und PlattenformTa slovenski standard je istoveten z:EN 15102:2007SIST EN 15102:2008en,fr,de91.180ICS:SLOVENSKI
STANDARDSIST EN 15102:200801-april-2008

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15102November 2007ICS 91.180 English VersionDecorative wallcoverings - Roll and panel form productsRevêtements muraux décoratifs - Rouleaux et panneauxDekorative Wandbekleidungen - Rollen- und PlattenformThis European Standard was approved by CEN on 23 September 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15102:2007: E

Factory production control.11 A.1 General.11 A.2 General requirements.11 A.3 Equipment.12 A.3.1 Testing.12 A.3.2 Manufacturing.12 A.4 Raw materials.12 A.5 Product testing and evaluation.12 A.6 Non-conforming products.13 A.7 Traceability.13 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 89/106/EEC, EU Construction Products Directive.14 ZA.1 Scope and relevant characteristics.14 ZA.2 Procedures for the attestation of conformity of wallcovering products in roll or panel form.16 ZA.2.1 Systems of attestation of conformity.16 ZA.2.2 EC certificate of conformity and EC declaration of conformity.18 ZA.3 CE marking and labelling.19 ZA.3.1 General information for CE marking.19 ZA.3.2 Minimum CE marking information.20 ZA.3.3 Complete CE marking information.20 Bibliography.23

1 Scope This European Standard applies to all forms of wallcovering products in roll and panel form as defined in
EN 235 supplied for hanging onto internal walls, partitions or ceilings, by means of an adhesive, whose primary purpose is decorative. However, certain wallcovering products may confer minor sound absorbtion and thermal resistance properties. It also provides for the evaluation of conformity of products to the requirements of this standard. It does not apply to wall coverings whose primary purpose is structural or protective (e.g. vapour or moisture barriers). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 71-3:1994, Safety of toys — Part 3: Migration of certain elements EN 12149:1997, Wallcoverings in roll form — Determination of migration of heavy metals and certain other elements, of vinyl chloride monomer and of formaldehyde release EN 12524, Building materials and products — Hygrothermal properties — Tabulated design values EN 12667, Thermal performance of building materials and products — Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance EN 12781:2001, Wallcoverings — Specification for cork panels EN 13085:2001, Wallcoverings — Specification for cork rolls EN 13238, Reaction to fire tests for building products — Conditioning procedures and general rules for selection of substrates EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using data from reaction to fire tests EN ISO 354, Acoustics — Measurement of sound absorption in a reverberation room (ISO 354:2003) EN ISO 9001:2000, Quality management systems — Requirements (ISO 9001:2000) EN ISO 11654, Acoustics — Sound absorbers for use in buildings — Rating of sound absorption (ISO 11654:1997)

4.2 Release of formaldehyde The release of formaldehyde from the wallcovering product shall be declared when subject to regulatory requirement and may be declared otherwise. The formaldehyde release, when tested in accordance with Test C of EN 12149:1997 (as modified in Annex A of EN 12781:2001 or EN 13085:2001 for cork wallcovering products in panel form and roll form respectively) shall not exceed 120 mg/kg of wallcovering. If no formaldehyde or products containing formaldehyde are added during the manufacturing process of the wallcovering product, and the raw materials are declared by the supplier to contain less than 120 mg/kg of formaldehyde, then testing is not necessary. 4.3 Release of dangerous substances 4.3.1 Heavy metals and specific elements 4.3.1.1 Requirements The migration of heavy metals and specific elements from the wallcovering product, expressed as mg/kg of wallcovering, shall not exceed the values given in Table 1 (after correction according to 4.3.1.2) when

Antimony Sb No upper limit Arsenic As 25 Barium Ba 500 Cadmium Cd 25 Chromium Cr 60 Lead Pb 90 Mercury Hg 20 Selenium Se 165
Table 2 — Analytical correction factor
Element Sb As Ba Cd Cr Pb Hg Se Analytical correction factor (in percentage) 60 60 30 30 30 30 50 60

If no polyvinyl chloride or products containing vinyl chloride are used during the manufacturing process of the wallcovering product or if the raw materials used are declared by the supplier to contain less than 1 mg/kg of vinyl chloride monomer, then testing on VCM release is not necessary. 4.4 Sound absorption The sound absorption of the wallcovering product shall be declared when its intended end use is subject to regulatory requirement and may be declared otherwise. It shall be measured in accordance with EN ISO 354 and expressed as a single number rating according to EN ISO 11654. 4.5 Thermal resistance The thermal resistance of the wallcovering product shall be declared when its intended end use is subject to regulatory requirement and may be declared otherwise. The value shall either be taken from EN 12524 or the products shall be tested in accordance with EN 12667 and a value declared in m2K/W or W/(mK). 5 Evaluation of conformity 5.1 General The conformity of the wallcovering product with the requirements of this standard and with the stated values (including classes) shall be demonstrated by: - initial type testing, - factory production control by the manufacturer, including product assessment (see Annex A). For the purposes of testing, wallcovering products may be grouped into families (see 3.2). 5.2 Initial type testing 5.2.1 General Initial type testing shall be performed to show conformity of the wallcovering product with this standard. Tests previously performed in accordance with the provisions of this standard (same product, same characteristic(s), test method, sampling procedure, system of attestation of conformity, etc.) may be taken into account. In addition, initial type testing shall be performed at the beginning of the production of a new product type (unless a member of the same family) or at the beginning of a new method of production (where this may affect the stated properties). All characteristics in Clause 4 shall be subject to initial type testing. Whenever a change occurs in the product raw materials, raw material suppliers, or the production process (subject to the definition of a family), which may change significantly one or more of the characteristics given in Clause 4, then the initial type testing shall be repeated for the appropriate characteristic(s).

See 4.4 Thermal resistance 4.5 EN 12667 EN 12524 See Note
See 4.5
NOTE Three specimens, each sample from a separate unit, with units selected according to the procedure of 5.2.2.1.
5.3 Factory production control (FPC) The manufacturer shall establish, document and maintain an FPC system to ensure that the subsequent wallcovering products placed on the market conform to the declared performance characteristics obtained on the basis of initial type testing. The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the use of the results to control raw and other incoming materials or components, equipment, the production process and the product. The FPC system shall comply with at least the requirements of Annex A.

Factory production control A.1 General The manufacturer shall establish, document and maintain a factory production control (FPC) system to ensure that the subsequent wallcovering products placed on the market conform to the declared performance characteristics. The FPC system shall consist of procedures, regular inspections and tests and/or assessments and the use of the results to control raw and other incoming materials or components, equipment, the production process and the product. All the elements, requirements a
...