EN 3017:2008
(Main)Aerospace series - Washers, facing/packing - Heat resisting steel
Aerospace series - Washers, facing/packing - Heat resisting steel
This standard specifies the characteristics of heat resisting steel, facing/packing washers for use in non load spreading aerospace applications at temperatures not exceeding 650 °C.
They are intended primarily for use as facing/packing washers under the head of bolts with strength classification up to 1 250 MPa to provide adequate clamping of slotted or recessed surfaces (especially on brackets and pipe clippings) and used for adjusting grip lengths of bolts.
These washers are not for use in load spreading applications for which EN 3016 washer shall be used.
Luft- und Raumfahrt - Dichtungsscheiben - Hochwarmfester Stahl
Diese Norm gilt für den nicht unterbrochenen Kriech und Zeitstandversuch unter konstanter Zugbeanspru¬chung an metallischen Werkstoffen nach Normen der Luft und Raumfahrt. Sie definiert die gegebenenfalls zu bestimmenden Eigenschaften sowie die zur Beschreibung der Prüfungen und Proben benutzten Begriffe. Sie legt die Maße der Proben und das Prüfverfahren fest. Die Dauer des Kriech und Zeitstandsversuchs nach dieser Norm ist auf 10 000 h bei einer maximalen Temperatur von 1 100 °C begrenzt.
Diese Norm kann auch auf metallische Werkstoffe mit einer Prüfdauer über 10 000 h und/oder Prüftempera¬turen über 1 100 °C angewendet werden, wenn dies vorher zwischen Hersteller und Käufer vereinbart wurde.
Série aérospatiale - Rondelles de garniture - Acier résistant à chaud
Aeronavtika - Tesnilne podložke - Toplotnoodporno jeklo
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2008
Aeronavtika - Tesnilne podložke - Toplotnoodporno jeklo
Aerospace series - Washers, facing/packing - Heat resisting steel
Luft- und Raumfahrt - Dichtungsscheiben - Hochwarmfester Stahl
Série aérospatiale - Rondelles de garniture - Acier résistant à chaud
Ta slovenski standard je istoveten z: EN 3017:2008
ICS:
49.030.50 Podložke in drugi blokirni Washers and other locking
elementi elements
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 3017
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2008
ICS 49.030.50
English Version
Aerospace series - Washers, facing/packing - Heat resisting
steel
Série aérospatiale - Rondelles de garniture - Acier résistant Luft- und Raumfahrt - Dichtungsscheiben - Hochwarmfester
à chaud Stahl
This European Standard was approved by CEN on 12 December 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3017:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Required characteristics.4
3.1 Configuration, dimensions, tolerances, masses.4
3.2 Materials .4
3.3 Surface roughness .4
3.4 Surface treatment .5
4 Designation .6
5 Marking .6
Figures
Figure 1 — Configuration. 5
Tables
Table 1 — Dimensions and masses. 5
Foreword
This document (EN 3017:2008) has been prepared by the Aerospace and Defence Industries Association of
Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.