EN ISO 11126-5:1998

SLOVENSKI STANDARD
01-junij-1998
Priprava jeklenih podlag pred nanašanjem barvnih in sorodnih premazov -
Specifikacije za nekovinske granulate za peskanje - 5. del: Nikljeva rafinirana
žlindra (ISO 11126-5:1993)
Preparation of steel substrates before application of paints and related products -
Specifications for non-metallic blast-cleaning abrasives - Part 5: Nickel refinery slag (ISO
11126-5:1993)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Anforderungen an nichtmetallische Strahlmittel - Teil 5: Strahlmittel aus
Nickelhüttenschlacke (ISO11126-5:1993)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Spécifications pour abrasifs non métalliques destinés a la préparation par
projection - Partie 5: Scories de raffinage du nickel (ISO 11126-5:1993)
Ta slovenski standard je istoveten z: EN ISO 11126-5:1998
ICS:
25.220.10 Priprava površine Surface preparation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

INTERNATIONAL
ISO
STANDARD
11126-5
First edition
1993-12-15
Preparation of steel Substrates before
application of paints and related
products - Specifications for non-metallic
blast-cleaning abrasives -
Part 5:
Nickel refinery slag
Preparation des subjectiles d’acier avant application de peintures et de
produits assimilh - Sp&ifications pour abrasifs non m6talliques
destinh A Ia prdparation par projection -
Partie 5: Stories de raffinage du nicke1
Reference number
ISO 11126-5:1993(E)
ISO 11126=5:1993(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national Standards bodies (ISO member bodies). The work
of preparing International Standards is normally carried out through ISO
technical committees. Esch member body interested in a subject for
which a technical committee has been established has the right to be
represented on that committee. International organizations, governmental
and non-governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 11126-5 was prepared by Technical Committee
lSO/6C 35, Paints and varnishes, Subcommittee SC 12, Preparation of
steel substra tes before application o f paints and related products.
ISO 11126 consists of the following Parts, under the general title Prep-
aration o f steel substra tes be fore applica tion o f paints and related
- Specifica tions for non-metallic blast-cleaning abrasives:
products
- Part 1: General introduction and classifica tion
- Part 2: Silica sand
- Part 3: Copper refinery slag
- Part 4: Coal furnace slag
- Part 5: Nickel refinery slag
- Part 6: Iron furnace slag
- Part 7: Fused aluminium Oxide
- Part 8: Olivine sand
- Part 9: Staurolite
0 ISO 1993
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronie or mechanical, including photocopying and
microfilm, without Permission in writing from the publisher.
International Organization for Standardization
Case Postale 56 l CH-l 211 Geneve 20 l Switzerland
Printed in Switzerland
63 ISO
ISO 11126=5:1993(E)
- Part 70: Garnet
At the time 0% publication of this part of ISO “11126, park 2, 7, 9 and ‘10
were in course of preparation.
Annex A of this part sf ISO 11126 is for information only.

This page intentionally left blank

INTERNATIONAL STANDARD 0 ISO ISO 11126-5:1993(E)
Preparation of steel Substrates before application of
paints and related products - Specifications for
non-metallic blast-cleaning abrasives -
Part 5:
Nickel refinery slag
WARNING - Equipment, materials and abrasives used for surface preparation tan be hazardous
if used carelessly. Many national regulations exist for those materials and abrasives that are
considered to be hazardous during or after use (waste management), such as free silica or
carcinogenic or toxic substances. These regulations are therefore to be observed. lt is important
to ensure that adequate instructions are given and that all required precautions are exercised.
niques are described in ISO 8504-2:1992, Reparation of
1 Scope
steel Substrates before application of pain ts and rela ted
products - Surface preparation methods - Part 2: Abras-
ive blas t-cleaning.
This patt of ISO 11126 specifies requirements for
nicke9 refinery slag abrasives, as supplied for blast-
cleaning processes. lt specifies ranges of particle
2 Normative references
simes and values for apparent density, Mohs hardness,
moisture content, conductivity of aqueous extract and
The following Standards contain provisions which,
water-soluble chlorides.
through reference in this text, constitute provisions
of this patt of ISO 11126. At the time of publication,
The requirements specified in this part of ISO 11126
the editions indicated were valid. All Standards are .
apply to abrasives supplied in the “ne,” condition
subject to revision, and Parties to agreements based
only. They do not apply to abrasives either during or
on this part of ISO 11126 are encouraged to investi-
after use.
gate the possibility of applying the most recent edi-
tions of the Standards indicated below. Members of
Test methods for non-metallic blast-cleaning
IEC and ISO maintain registers of currently valid
abrasives are given in the various Parts of
International Standards.
ISO 11127.
NOTES ISO 11127-1 :1993, Preparation of steel Substrates
before application of paints and related products -
l lnformation on commonly referenced national Standards
Test methods for non-metallic blast-cleaning abrasives
for non-metallic abrasives is given in annex A.
- Part 1: Sampling
...