EN 4626-002:2008

SLOVENSKI STANDARD
01-julij-2008
$HURQDYWLND.RQHNWRUMLRSWLþQLSUDYRNRWQLYHþNRQWDNWQLVVWRMDORPLQSORãþR
YGROELQD4XDGUD[VSUHPHURPNDSLFHPP'HORYQDWHPSHUDWXUDƒ&GR
ƒ&RGYLVQDRGNDEOD,]UDYQDQLNRQWDNWLGHO6SHFLILNDFLMDODVWQRVWLLQ
UD]SRUHGLWHYNRQWDNWRY
Aerospace series - Connectors, optical, rectangular, multicontact, rack and panel,
Quadrax cavity, 2,5 mm diameter ferrule - Operating temperatures - 65 °C to 125 °C
(cable dependent) - Flush contacts - Part 002: Specification of performance and contact
arrangements
Luft- und Raumfahrt - Optische Rechtecksteckverbinder, Quadrax-Kontaktkammer,
Durchmesser 2,5 mm Ferrule - Betriebstemperaturen - 65 °C bis 125 °C (vom Kabel
abhängig) - Bündige Kontakte - Teil 002: Leistungsdaten und Kontaktanordnungen
Série aérospatiale - Connecteurs, optique, rectangulaire, à contacts multiples, rackables,
cavité Quadrax, férule diamètre 2,5 mm - Température d’utilisation - 65 °C à 125 °C
(selon câble) - Contacts affleurants - Partie 002 : Spécification de performances et
arrangements des contacts
Ta slovenski standard je istoveten z: EN 4626-002:2008
ICS:
49.060 /HWDOVNDLQYHVROMVND Aerospace electric
HOHNWULþQDRSUHPDLQVLVWHPL equipment and systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 4626-002
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 49.060
English Version
Aerospace series - Connectors, optical, rectangular,
multicontact, rack and panel, Quadrax cavity, 2,5 mm diameter
ferrule - Operating temperatures - 65 °C to 125 °C (cable
dependent) - Flush contacts - Part 002: Specification of
performance and contact arrangements
Série aérospatiale - Connecteurs, optique, rectangulaire, à Luft- und Raumfahrt - Optische Rechtecksteckverbinder,
contacts multiples, rackables, cavité Quadrax, férule Quadrax-Kontaktkammer, Durchmesser 2,5 mm Ferrule -
diamètre 2,5 mm - Température d'utilisation - 65 °C à 125 Betriebstemperaturen - 65 °C bis 125 °C (vom Kabel
°C (selon câble) - Contacts affleurants - Partie 002 : abhängig) - Bündige Kontakte - Teil 002: Leistungsdaten
Spécification de performances et arrangements des und Kontaktanordnungen
contacts
This European Standard was approved by CEN on 28 December 2007.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4626-002:2008: E
worldwide for CEN national Members.

Contents Page
Foreword.3
1 Scope .4
2 Normative references .4
3 Terms and definitions .4
4 List of product standard .5
5 General characteristics .5
5.1 Climatic characteristics .5
5.2 Mechanical characteristics .5
6 Housing sizes and contact arrangements .5
7 Combination.11
8 Filler plugs and dummy contacts.11

Foreword
This document (EN 4626-002:2008) has been prepared by the Aerospace and Defence Industries Association
of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of ASD,
prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at
the latest by October 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This standard was reviewed by the Domain Technical Coordinator of ASD-STAN's Electrical Domain.
After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STAN's General
Process Manual, this standard has received approval for Publication.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia,
...