EN 2565:2013

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SUHVNXãDQMDLuft- and Raumfahrt - Herstellen von CFK-PrüfplattenSérie aérospatiale - Préparation de panneaux à base de résine et fibres de carbone destinés à l'élaboration d'éprouvettesAerospace series - Preparation of carbon fibre reinforced resin panels for test purposes49.025.99Drugi materialiOther materialsICS:Ta slovenski standard je istoveten z:EN 2565:2013SIST EN 2565:2014en01-marec-2014SIST EN 2565:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2565
August 2013 ICS 49.025.40 English Version
Aerospace series - Preparation of carbon fibre reinforced resin panels for test purposes
Série aérospatiale - Préparation de panneaux à base de résine et fibres de carbone destinés à l'élaboration d'éprouvettes
Luft- and Raumfahrt - Herstellen von CFK-Prüfplatten This European Standard was approved by CEN on 8 May 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2565:2013: ESIST EN 2565:2014

4.1.2 Autoclave of any dry heat type with the following requirements: a) as 4.1.1 (a); b) a heat up speed of at least 3 °C/min; c) capable of maintaining the required pressure to an accuracy of 10 kPa over the period of time required for curing of the resin; d) vacuum pumps capable of applying a vacuum equal to at least 80 kPa. 4.1.3 Ruler for measuring length and width to an accuracy of 0,5 mm 4.1.4 Micrometer screw type with an accuracy of 0,01 mm for measuring the thickness
4.1.5 Balance with an accuracy of 0,01 g 4.1.6 Cutting device such as a knife with a sharp blade 4.2 Materials 4.2.1 Metal lay-up plate of 500 mm × 500 mm × 7 mm or any other suitable dimensions agreed upon between the parties concerned. 4.2.2 When necessary, metal cover plate of 300 mm × 300 mm × 7 mm or any other suitable dimensions agreed upon between the parties concerned. 4.2.3 Where required, rubber pressure retaining rings resistant to a temperature at least 20 °C higher than the actual curing temperature. 4.2.4 Release film resistant to a temperature at least 20 °C higher than the actual curing temperature, such as polyvinylfluoride (PVF), polytetrafluoroethylene (PTFE) or PTFE coated fabric. 4.2.5 When necessary, perforated release film resistant to a temperature at least 20 °C higher than the actual curing temperature, such as PTFE or PTFE coated fabric. 4.2.6 Pressure blanket material with the
...