EN 12722:2009+A1:2013
(Main)Furniture - Assessment of surface resistance to dry heat
Furniture - Assessment of surface resistance to dry heat
This European Standard specifies a method for the assessment of the resistance to dry heat of all rigid furniture surfaces regardless of materials.
It does not apply to leather and textile surfaces.
The test is intended to be carried out on a part of the finished furniture, but can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test.
The test should be carried out on unused surfaces.
Annex A (informative) describes a direct light source.
Möbel - Bewertung der Beständigkeit von Oberflächen gegen trockene Hitze
Diese Europäische Norm legt ein Bewertungsverfahren für die Beständigkeit von Oberflächen gegen trockene Wärme fest und gilt für starre Möbeloberflächen unabhängig vom verwendeten Werkstoff.
Sie gilt nicht für Oberflächen aus Leder und Textilien.
Die Prüfung ist zur Durchführung an einem Teil des oberflächenbehandelten Möbelstücks gedacht, kann aber auch an Prüflingen durchgeführt werden, die aus dem gleichen Werkstoff mit identischer Oberflächen-behandlung wie das oberflächenbehandelte Produkt und groß genug sind, um den Anforderungen der Prüfung zu entsprechen.
Die Prüfung muss auf unbenutzten Oberflächen durchgeführt werden.
Meubles - Évaluation de la résistance de la surface à la chaleur sèche
La présente Norme européenne spécifie une méthode d’évaluation de la résistance à la chaleur sèche de toutes les surfaces d’ameublement indépendamment des matériaux.
Elle ne s’applique pas aux surfaces en cuir et en textile.
L’essai est destiné à être réalisé sur une partie du meuble fini mais il peut être effectué sur des panneaux d’essai constitués du même matériau, de finition identique au produit fini et de dimensions suffisantes pour satisfaire aux spécifications de l’essai.
L’essai doit être conduit sur des surfaces neuves.
!texte supprimé"
Pohištvo - Ocenjevanje odpornosti površine proti suhi toploti (vključno z dopolnilom A1)
Ta evropski standard določa metodo za ocenjevanje odpornosti vseh trdnih površin pohištva ne glede na material proti suhi toploti. Ne uporablja se za usnjene in tekstilne površine. Preskus naj bi se izvedel na delu končanega kosa pohištva, lahko pa se izvede tudi na preskusnih ploščah iz istega materiala, ki so obdelane na identičen način kot končan izdelek, njihova velikost pa mora biti dovolj velika, da ustreza zahtevam preskusa. Preskus naj bi se izvedel na še nerabljenih površinah.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Möbel - Bewertung der Beständigkeit von Oberflächen gegen trockene HitzeMeubles - Évaluation de la résistance de la surface à la chaleur sècheFurniture - Assessment of surface resistance to dry heat97.140PohištvoFurnitureICS:Ta slovenski standard je istoveten z:EN 12722:2009+A1:2013SIST EN 12722:2009+A1:2014en,fr,de01-januar-2014SIST EN 12722:2009+A1:2014SLOVENSKI
STANDARDSIST EN 12722:20091DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12722:2009+A1
October 2013 ICS 97.140 Supersedes EN 12722:2009
English Version
Furniture - Assessment of surface resistance to dry heat
Meubles - Évaluation de la résistance de la surface à la chaleur sèche
Möbel - Bewertung der Beständigkeit von Oberflächen gegen trockene Hitze This European Standard was approved by CEN on 3 January 2009 and includes Amendment 1 approved by CEN on 3 September 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12722:2009+A1:2013: E SIST EN 12722:2009+A1:2014
Significant technical changes in revised edition of this standard . 11 Bibliography. 12
Tables Table 1 — Descriptive numerical rating code . 8
Figures Figure 1 — Aluminium block used as heat source . 6
Informative !Annex A" provides details of significant technical changes between this European Standard and the previous edition. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 12722:2009+A1:2014
1 Scope This European Standard specifies a method for the assessment of the resistance to dry heat of all rigid furniture surfaces regardless of materials. It does not apply to leather and textile surfaces. The test is intended to be carried out on a part of the finished furniture, but can be carried out on test panels of the same material, finished in an identical manner to the finished product, and of a size sufficient to meet the requirements of the test. The test should be carried out on unused surfaces. !deleted text" 2 Normative references !The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies." EN ISO 4287:1998, Geometrical Product Specifications (GPS) – Surface texture: Profile method – Terms, definitions and surface texture parameters (ISO 4287:1997) EN ISO 4288:1997, G
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.