Industrial valves - Actuators - Part 3: Pneumatic part-turn actuators for industrial valves - Basic requirements

This document specifies basic requirements for pneumatic part-turn valve actuators, both double acting and single acting, used for on-off and modulating control duties.
It includes guidelines, recommendations and methods for enclosure and corrosion protection, control and testing.
It does not apply to pneumatic actuators which are integral parts of control valves and to pneumatic actuators designed for permanent immersion in fresh or sea water.
Other requirements, or conditions of use, different from those indicated in this document, are expected to be subject to negotiations, between the purchaser and the manufacturer/supplier, prior to order.

Industriearmaturen - Antriebe - Teil 3: Pneumatische Schwenkantriebe für Industriearmaturen - Grundanforderungen

Dieses Dokument legt Grundanforderungen sowohl an in beide Richtungen als auch an in eine Richtung wirkende pneumatische Schwenkantriebe für Armaturen für Auf-Zu- und Modulations-Regelfunktionen fest.
Es enthält Leitlinien, Empfehlungen sowie Verfahren für Gehäuse- und Korrosionsschutz, Kontrollen und Prüfungen.
Es ist nicht anwendbar für pneumatische Stellantriebe, die integraler Bestandteil von Regelventilen sind, oder für pneumatische Stellantriebe, die für ständiges Eintauchen in Süß- oder Meerwasser ausgelegt sind.
Es wird erwartet, dass andere Anforderungen oder Anwendungsbedingungen als die, die in diesem Dokument angegebenen sind, vor Auftragserteilung zwischen dem Käufer und dem Hersteller/Lieferanten verhandelt werden.

Robinetterie industrielle - Actionneurs - Partie 3 : Actionneurs pneumatiques à fraction de tour pour robinetterie industrielle - Prescriptions de base

Le présent document spécifie les prescriptions de base pour les actionneurs pneumatiques à fraction de tour d’appareil de robinetterie à double et à simple effet, utilisés pour les fonctions tout ou rien et les fonctions de régulation.
Il comprend des lignes directrices, des recommandations et des méthodes pour la protection de l’enceinte et contre la corrosion, le contrôle et les essais.
Il ne s’applique pas aux actionneurs pneumatiques qui font partie intégrante de robinets de régulation, ni aux actionneurs pneumatiques, conçus pour une immersion permanente dans l’eau douce ou l’eau de mer.
Des prescriptions ou conditions relatives à l’utilisation, autres que celles mentionnées dans le présent document, sont prévues pour être négociées entre l’acheteur et le fabricant/fournisseur, avant la commande.

Industrijski ventili - Pogoni - 3. del: Pnevmatični pogoni z delnim zasukom za industrijske ventile - Osnovne zahteve

Ta dokument podaja osnovne zahteve za pnevmatične pogone z delnim zasukom za industrijske ventile z dvosmernim in enosmernim delovanjem, ki se uporabljajo za vklopno-izklopne in modulacijsko krmilne naloge. Vključuje smernice, priporočila in metode za zaščito, nadzor ter preskušanje ohišij in proti koroziji.
Ne uporablja se za pnevmatične pogone, ki so sestavni deli regulacijskih ventilov.
O drugih zahtevah ali pogojih uporabe, ki niso navedeni v tem dokumentu, se morata kupec in proizvajalec/dobavitelj dogovoriti pred naročilom.
Izrazi in definicije v zvezi s tem evropskim standardom so navedene v predlogu standarda FprEN 15714-1.

General Information

Status
Published
Publication Date
18-Oct-2022
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
19-Oct-2022
Due Date
23-Dec-2022
Completion Date
19-Oct-2022

Relations

Buy Standard

Standard
EN 15714-3:2023
English language
30 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2023
Nadomešča:
SIST EN 15714-3:2011
Industrijski ventili - Pogoni - 3. del: Pnevmatični pogoni z delnim zasukom za
industrijske ventile - Osnovne zahteve
Industrial valves - Actuators - Part 3: Pneumatic part-turn actuators for industrial valves -
Basic requirements
Industriearmaturen - Antriebe - Teil 3: Pneumatische Schwenkantriebe für
Industriearmaturen - Grundanforderungen
Robinetterie industrielle - Actionneurs - Partie 3 : Actionneurs pneumatiques à fraction de
tour pour robinetterie industrielle - Prescriptions de base
Ta slovenski standard je istoveten z: EN 15714-3:2022
ICS:
23.060.20 Zapirni ventili (kroglasti in Ball and plug valves
pipe)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 15714-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 23.060.20 Supersedes EN 15714-3:2009
English Version
Industrial valves - Actuators - Part 3: Pneumatic part-turn
actuators for industrial valves - Basic requirements
Robinetterie industrielle - Actionneurs - Partie 3 : Industriearmaturen - Antriebe - Teil 3: Pneumatische
Actionneurs pneumatiques à fraction de tour pour Schwenkantriebe für Industriearmaturen -
robinetterie industrielle - Prescriptions de base Grundanforderungen
This European Standard was approved by CEN on 19 September 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15714-3:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Classification/Designation . 8
4.1 Duty classification . 8
4.1.1 General. 8
4.1.2 On-off duty . 8
4.1.3 Modulating duty . 8
4.2 Action . 8
4.2.1 Double Acting (DA) . 8
4.2.2 Single Acting (SA) . 8
5 Motive energy . 8
5.1 Operating medium. 8
5.2 Quality . 8
5.3 Pressure . 9
6 Actuator performance data . 9
6.1 Minimum moving pressure . 9
6.2 Operating time . 9
6.3 Displacement volume . 9
7 Basic design requirements . 9
7.1 Safety requirements . 9
7.2 Actuator attachment . 9
7.3 Angular stroke . 10
7.4 Endurance of part-turn actuators . 10
7.5 Leakage . 11
7.6 Environmental conditions . 11
7.6.1 Ambient temperature. 11
7.6.2 Enclosure protection . 11
7.6.3 Corrosion protection . 11
7.7 Pressure connections . 12
7.7.1 General. 12
7.7.2 Remotely mounted pilot valves . 13
7.7.3 Direct mounted pilot valves . 14
7.8 Pressure connections for single acting actuators . 15
7.9 Fail safe direction for single acting actuators . 15
7.10 Structural safety factors . 15
7.11 Position indication . 16
8 Optional equipment . 16
8.1 Ancillaries . 16
8.2 Manual operation . 19
8.3 Mechanical end stop adjustment . 19
9 Conformity assessment . 19
9.1 General . 19
9.2 Type tests . 19
9.3 Control of production process . 20
10 Marking . 21
10.1 Basic requirements on marking . 21
10.2 Optional information . 22
11 Documentation . 22
12 Part-turn actuator selection guidelines . 22
Annex A (normative) Actuator type test procedure . 23
A.1 General . 23
A.2 Test equipment. 23
A.3 Test conditions . 23
A.4 Test procedure . 23
A.4.1 Initial tests . 23
A.4.2 Endurance test . 24
A.4.3 Final tests. 24
A.5 Acceptance criteria . 24
Annex B (informative) Actuator selection guidelines . 25
B.1 General . 25
B.2 Selection parameters . 25
B.2.1 General . 25
B.2.2 Valve questions . 25
B.2.3 Actuator questions . 25
B.2.4 Ancillary questions . 26
B.2.5 Environmental conditions . 26
B.3 Actuator selection . 26
B.3.1 General . 26
B.3.2 Torque characteristics for rack and pinion or vane actuators . 27
B.3.3 Torque characteristics for scotch yoke actuators (e.g. symmetric system) . 28
Bibliography . 30

European foreword
This document (EN 15714-3:2022) has been prepared by Technical Committee CEN/TC 69 “Industrial
valves”, the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shal
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.