EN ISO 5436-2:2001/prA1

SLOVENSKI STANDARD
01-oktober-2010
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7HNVWXUDSRYUãLQHSURILOQDPHWRGD
VWDQGDUGL]DPHULOQRRSUHPRGHO6WDQGDUGL]DPHULOQRSURJUDPVNRRSUHPR
'RSROQLOR,62'$0
Geometrical Product Specifications (GPS) - Surface texture: Profile method;
Measurement standards - Part 2: Software measurement standards - Amendment 1 (ISO
5436-2:2001/DAM 1:2010)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit:
Tastschnittverfahren; Normale - Teil 2: Software-Normale (ISO 5436-2:2001/DAM
1:2010)
Spécification géométrique des produits (GPS) - État de surface: Méthode du profil;
Étalons - Partie 2: Étalons logiciels - Amendement 1 (ISO 5436-2:2001/DAM 1:2010)
Ta slovenski standard je istoveten z: EN ISO 5436-2:2001/prA1
ICS:
17.040.30 Merila Measuring instruments
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
DRAFT
EN ISO 5436-2:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
July 2010
ICS 17.040.30
English Version
Geometrical Product Specifications (GPS) - Surface texture:
Profile method; Measurement standards - Part 2: Software
measurement standards - Amendment 1 (ISO 5436-2:2001/DAM
1:2010)
Spécification géométrique des produits (GPS) - État de
surface: Méthode du profil; Étalons - Partie 2: Étalons
logiciels - Amendement 1 (ISO 5436-2:2001/DAM 1:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.

This draft amendment A1, if approved, will modify the European Standard EN ISO 5436-2:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5436-2:2001/prA1:2010: E
worldwide for CEN national Members.

Contents Page
Foreword .3

Foreword
This document (EN ISO 5436-2:2001/prA1:2010) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 5436-2:2001/DAM 1:2010 has been approved by CEN as a EN ISO 5436-2:2001/prA1:2010
without any modification.
DRAFT AMENDMENT ISO 5436-2:2001/DAmd 1
ISO/TC 213 Secretariat: DS
Voting begins on: Voting terminates on:
2010-07-29 2010-12-29
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Geometrical Product Specifications (GPS) — Surface texture:
Profile method; Measurement standards —
Part 2:
Software measurement standards
AMENDMENT 1
Spécification géométrique des produits (GPS) — État de surface: Méthode du profil; Étalons —
Partie 2: Étalons logiciels
AMENDEMENT 1
ICS 17.040.30
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition d
...