iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 12063:2024

(Main)

Execution of special geotechnical work - Sheet pile walls, combined pile walls, high modulus walls

Execution of special geotechnical work - Sheet pile walls, combined pile walls, high modulus walls

This document specifies requirements, recommendations and information concerning the execution of permanent or temporary sheet pile wall, combined pile walls, high modulus wall structures and the handling of equipment and materials.
This document does not give requirements and recommendations for the installation of specific parts of the structure such as ground anchorages, displacement piles and micropiles which are covered by other documents.
This document is applicable to steel sheet pile walls, combined walls, high modulus walls, and synthetic sheet pile walls (composite), precast concrete and timber sheet pile walls. Tubular piles included in combined walls and high modulus walls can be filled with concrete.
Composite structures such as Berliner walls and sheet pile walls in combination with shotcrete, are not covered by this document.

Ausführung von Arbeiten im Spezialtiefbau - Spundwandkonstruktionen

Dieses Dokument legt Anforderungen, Empfehlungen und Hinweise über die Ausführung von bleibenden oder temporären Spundwandkonstruktionen, kombinierten Spundwänden und Trägerpfahlwänden sowie über die hierzu erforderliche Handhabung von Geräten und Materialien fest.
Dieses Dokument beinhaltet keine Anforderungen und Empfehlungen für die Errichtung von spezifischen Teilen des Bauwerkes, wie etwa Ankern, Verdrängungspfählen und Mikropfählen, die in anderen Dokumenten behandelt werden.
Dieses Dokument gilt lediglich für Stahlspundwände, kombinierte Spundwände, Trägerpfahlwände und Kunststoffspundwände (Verbundstoff), vorgefertigte Betonspundwände und Holzspundwände. Rohrpfähle in kombinierten Spundwänden und Trägerpfahlwände können mit Beton gefüllt sein.
Konstruktionen aus unterschiedlichen Baustoffen, wie z. B. Berliner Verbau oder Spundwandkonstruktionen mit Spritzbeton werden in diesem Dokument nicht behandelt.

Exécution des travaux géotechniques spéciaux - Rideaux de palplanches, rideaux mixtes, rideaux à forte inertie

Ce document spécifie les prescriptions, les recommandations et des informations concernant l'exécution des structures permanentes ou temporaires en rideaux de palplanches, rideaux mixtes et rideaux à forte inertie et celles relatives à la manutention des équipements et des profilés.
Ce document ne donne pas de prescriptions ni de recommandations pour la mise en place des éléments spécifiques de structure, comme les tirants d'ancrage, les pieux mis en place par refoulement du sol et les micropieux, qui sont couverts par d'autres normes.
Ce document s’applique aux rideaux de palplanches en acier, aux rideaux mixtes, aux rideaux à forte inertie, aux rideaux de palplanches synthétiques, aux rideaux de palplanches en béton préfabriqué et en bois. Les profilés tubulaires intégrés aux rideaux mixtes et à forte inertie peuvent être remplis de béton.
Les structures composées, comme les parois berlinoises et les parois formées de palplanches et de béton projeté, ne sont pas traitées par le présent document.

Izvedba posebnih geotehničnih del - Zagatne stene, kombinirane zagatne stene, visoke modularne stene

General Information

Status
Published
Publication Date
21-May-2024
ICS
93.020 - Earthworks. Excavations. Foundation construction. Underground works
Technical Committee
CEN/TC 288 - Execution of special geotechnical works
Drafting Committee
CEN/TC 288/WG 19 - Sheet-pile walls
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
22-May-2024
Due Date
27-Nov-2021
Completion Date
22-May-2024
Ref Project
SIST EN 12063:2024 - Execution of special geotechnical work - Sheet pile walls, combined pile walls, high modulus walls

Relations

Replaces
EN 12063:1999 - Execution of special geotechnical work - Sheet-pile walls
Effective Date
18-Jan-2023

Buy Standard

EN 12063:2024EN 12063:2024
PreviousNext
Standard
EN 12063:2024
English language
134 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-julij-2024
Izvedba posebnih geotehničnih del - Zagatne stene, kombinirane zagatne stene,
visoke modularne stene
Execution of special geotechnical work - Sheet pile walls, combined pile walls, high
modulus walls
Ausführung von Arbeiten im Spezialtiefbau - Spundwandkonstruktionen
Exécution des travaux géotechniques spéciaux - Rideaux de palplanches, rideaux
mixtes, rideaux à forte inertie
Ta slovenski standard je istoveten z: EN 12063:2024
ICS:
93.020 Zemeljska dela. Izkopavanja. Earthworks. Excavations.
Gradnja temeljev. Dela pod Foundation construction.
zemljo Underground works
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 12063
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2024
EUROPÄISCHE NORM
ICS 93.020 Supersedes EN 12063:1999
English Version
Execution of special geotechnical work - Sheet pile walls,
combined pile walls, high modulus walls
Exécution des travaux géotechniques spéciaux - Ausführung von Arbeiten im Spezialtiefbau -
Rideaux de palplanches, rideaux mixtes, rideaux à forte Spundwandkonstruktionen
inertie
This European Standard was approved by CEN on 15 April 2024.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12063:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions and symbols . 8
3.1 Terms and definitions . 8
4 Information needed for the execution of the work . 20
4.1 General information . 20
4.2 Specific information . 21
4.3 Execution classes . 22
5 Site investigation. 22
5.1 Geotechnical investigation . 22
5.2 Specific requirements . 22
5.3 Driveability of sheet piles . 23
6 Materials and products . 24
6.1 Steel sheet piles and other steel components . 24
6.2 Timber sheet piles . 24
6.3 Synthetic sheet piles . 24
6.4 Other materials and products . 24
6.5 Corrosion protection for steel sheet piles and preservation of timber and synthetic
sheet piles . 24
6.6 Sealings for interlock connections . 24
6.7 Environmental product declaration (EPD) . 25
7 Considerations related to design . 25
7.1 General. 25
7.2 Selection of a pile type . 25
7.3 Other structural elements . 26
7.4 Sequence of execution . 26
7.5 Specific design related considerations . 27
8 Execution of sheet pile wall structures . 28
8.1 General. 28
8.2 Site preparation. 28
8.3 Storage and handling of the sheet piles . 28
8.4 Welding and cutting of steel elements . 29
8.5 Installation . 50
8.6 Tolerances regarding plan position and verticality . 54
8.7 Corrections of pile position during driving . 55
8.8 Installation of anchorages . 56
8.9 Walings and struts . 56
8.10 Excavation, backfilling, draining and de-watering . 57
8.11 Extraction of sheet piles . 58
8.12 Rock dowels and anchor bolts. 58
8.13 Sealing . 60
9 Supervision, testing and monitoring . 60
9.1 Supervision . 60
9.2 Testing . 61
9.3 Monitoring. 61
10 Site records . 62
10.1 Records in connection with execution . 62
10.2 Records at completion of the execution works . 62
11 Special requirements . 62
11.1 Safety . 62
11.2 Impact on the surrounding buildings and installations . 63
11.3 Noise hindrance . 63
11.4 Permeability of pile walls . 63
Annex A (informative) Handling and storage of sheet piles. 64
A.1 General . 64
A.2 Hoisting . 64
A.3 Storage . 68
A.4 Special devices . 71
Annex B (normative) Welding of sheet piles . 76
B.1 General . 76
B.2 Butt welding multiple lengths . 76
B.3 Welding multiple lengths by splicing with plates . 77
B.4 Junction piles (U and Z-form piles) for jointing a part wall element to the main wall
................................................................................................................................................................... 78
B.5 Special corner piles . 80
B.6 Straight web junction pile . 81
B.7 Box piles . 84
B.8 Sealing welds . 86
Annex C (informative) Driving of sheet piles . 90
C.1 General . 90
Annex D (informative) Installation and driving assistance. 92
D.1 Driving method for standard sheet pile walls . 92
D.2 Driving method for combined sheet pile walls . 94
D.3 Driving assistance . 95
Annex E (informative) Watertightness of interlock sealings . 97
E.1 General considerations . 97
E.2 A simple case of assessing the discharge through a steel sheet pile wall . 98
E.3 Worked example for the assessment of the total inflow into a building pit . 100
Annex F (normative) Timber sheet piles and walings . 101
F.1 General . 101
F.2 Delivery of timber sheet piles and walings . 101
F.3 Quality requirements .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 12715:2020(Main)
Execution of special geotechnical work - Grouting
SIST EN 12715:2021

This document is applicable to the execution, testing and monitoring of geotechnical grouting work.
Grouting for geotechnical purposes (geotechnical grouting) is a process in which the remote placement of a pumpable material in the ground is indirectly controlled by adjusting its rheological characteristics and by the manipulation of the placement parameters (pressure, volume and the flow rate).
The following principles and methods of geotechnical grouting are covered by this document:
-   displacement grouting (compaction and compensation grouting);
-   grouting without displacement of the host material (permeation, fissure/contact grouting, bulk filling).
Figure 1 illustrates the various injection methods associated with these two principles.
NOTE   The term consolidation grouting is sometimes used to emphasize an improvement in the strength or deformation characteristics of a soil or rock mass, with the aim that it does not undergo any unacceptable deformation. The term compensation grouting is used when the objective of grouting is to concurrently compensate for ground loss.
The principal objectives of geotechnical grouting are:
-   the modification of the hydraulic/hydrogeological characteristics of the ground;
-   the modification of the mechanical properties of the ground;
-   the filling of natural cavities, mine workings, voids adjacent to structures;
-   inducing displacement to compensate for ground loss or to stabilize and lift footings, slabs and pavements.
Specialized grouting activities, generally associated with structural and/or emergency works, are not covered by this document.
The execution, testing and monitoring of jet grouting work is not covered by this document and is covered by EN 12716.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12716:2018(Main)
Execution of special geotechnical work - Jet grouting
SIST EN 12716:2019

This document establishes general principles for the execution of jet grouting works.
NOTE   The jet grouting processes is distinguished from the grouting processes covered by EN 12715.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1536:2010+A1:2015(Main)
Execution of special geotechnical work - Bored piles
SIST EN 1536:2011+A1:2015

1.1   This European Standard establishes general principles for the execution of bored piles (see 3.2).
NOTE 1   This standard covers piles or barrettes which are formed in the ground by excavation and are structural members used to transfer actions and/or limit deformations.
NOTE 2   This standard covers piles with circular cross-section (see Figures 1 and A.1a)) and barrettes (see 3.3) with rectangular, T or L or any other similar cross-section (see Figure 2) concreted in a single operation.
NOTE 3   In the standard the term pile is used for circular cross-section structure and the term barrette for other shapes. Both are bored piles.
1.2    This European Standard applies to bored piles (see Figure 3) with:
-   uniform cross-section (straight shaft);
-   telescopically changing shaft dimensions;
-   excavated base enlargements; or
-   excavated shaft enlargements.
NOTE    The shape of a pile base and of an enlargement depends on the tool used for the excavation.
1.3    This European Standard applies (see Note) to:
-   bored piles with a depth to width ratio  5;
-   piles (see Figures 1 and 3) with a shaft diameter 0,3 m  D  3,0 m;
-   barrettes (see Figure 2) with the least dimension Wi  0,4 m, a ratio LBiB / Wi between its largest and its least dimensions  6 and a cross-sectional area A  15 m²;
-   piles with circular precast elements used as structural member (see Figure 7) with a least dimension DP  0,3 m;
-   barrettes with rectangular precast elements used as structural member with a least dimension WP  0,3 m.
NOTE   The standard covers a large range of diameters. For small diameter bored piles less than 450 mm, the general specification can be adapted to cater for the lack of space (e.g. minimum bars number and spacing).
1.4    This European Standard applies to piles with the following rake (see Figure 4):
-   n  4 (  76°);
-   n  3 (  72°) for permanently cased piles.
(...)

  • Standard
    82 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1538:2010+A1:2015(Main)
Execution of special geotechnical work - Diaphragm walls
SIST EN 1538:2011+A1:2015

This European Standard establishes general principles for the execution of diaphragm walls as either retaining walls or cut-off walls.
NOTE 1   This standard covers only structures constructed in a trench excavated with a support fluid or in dry conditions, where soil is removed and replaced by concrete or slurry and with wall thickness B ≥ 40 cm.
NOTE 2   Diaphragm walls can be permanent or temporary structures.
NOTE 3   The following types of structure are considered:
a)   retaining walls: usually constructed to support the sides of an excavation in the ground. They include:
1)   cast in situ concrete diaphragm walls;
2)   precast concrete diaphragm walls;
3)   reinforced slurry walls;
b)   cut-off walls: usually constructed to prevent migration of groundwater, clear or polluted, or of other contaminants present in the ground. They include:
1)   slurry walls (possibly with membranes or sheet piles);
2)   plastic concrete walls.
NOTE 4   Walls formed shallow vertical trenches (typically excavations with a ratio of depth over thickness D/B < 5 or D < 5 m) are not covered by this standard.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14199:2015(Main)
Execution of special geotechnical works - Micropiles
SIST EN 14199:2015

1.1   This European Standard establishes general principles for the execution of micropiles.
They are for drilled piles constructed using a drilling tool with a diameter less than 300 mm.
NOTE 1   This European Standard is not applicable to driven piles, the execution of which is governed by EN 12699.
NOTE 2   For a definition of shaft diameter see 3.3.
1.2   Micropiles are structural members to transfer actions to the ground and can contain bearing elements to transfer directly or indirectly loads and or to limit deformations. For examples of micropiles see Figure 1, Figure 2 and Figure 3. Their shaft and base resistance can be improved (mostly by grouting) and they can be constructed with (see Figure 4):
-   uniform cross section (straight shaft); or
-   telescopically changing shaft dimensions;
-   shaft enlargements; and/or
-   base enlargement.
1.3   Other than practical considerations, there are no limitations regarding, length, inclination (definition of inclination, see Figure 5), slenderness ratio or shaft and base enlargements.
1.4   The provisions of this European Standard apply to (see Figure 6):
-   single micropiles;
-   micropile groups;
-   reticulated micropiles;
-   micropile walls.
1.5   The material of micropiles covered by this European Standard can be:
-   steel or other reinforcement materials;
-   grout, mortar or concrete;
-   a combination of above.
1.6   Micropiles can be used for:
-   working under restricted access and/or headroom conditions;
-   foundations of new structures (particularly in very heterogeneous soil or rock formations);
-   reinforcing or strengthening of existing structures to increase the capacity to transfer load to depth with acceptable load settlement characteristics, e.g. underpinning works;
-   reducing settlements and/or displacements;
-   forming a retaining wall;
-   reinforcing of soil to form a bearing and/or retaining structure;
-   improving slope stability;
-   securing against uplift;
-   other applications where micropile techniques are appropriate.
1.7   Deep mixing columns according to EN 14679 are not included in this European Standard. Columns constructed by jet grouting are covered by EN 12716. Ground anchors are covered by EN 1537.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 12699:2015(Main)
Execution of special geotechnical works - Displacement piles
SIST EN 12699:2015

1.1   This European Standard establishes general principles for the execution of displacement piles, that means piles which are installed in the ground without excavation or removal of material from the ground except for limiting heave and/or limiting vibration as well as removal of obstructions or to assist penetration.
Piles are driven into the ground using impact, vibration, pressing, screwing or a combination of these methods.
1.2   The material of displacement piles covered by this European Standard can be:
-   steel;
-   cast iron;
-   concrete, mortar;
-   timber;
-   grout;
-   combination of above.
1.3   This European Standard covers prefabricated, cast in situ, or a combination of these methods to form displacement piles of regular shape.
Examples are given in Figure A.2 and Figure A.3.
1.4   Displacement piles may be installed in soils enhanced by ground improvement techniques. The ground improvement can be executed before, at the same time or after installation of the piles.
1.5   Other than practical considerations there are for the purpose of this European Standard no limitations regarding cross section dimensions, shaft or base enlargements, length or rake.
1.6   The provisions of this European Standard apply to:
-   single piles;
-   pile groups;
-   concrete sheet piles.
1.7   Columns constructed by ground improvement techniques (such as mixed in situ columns, jet grouting, compaction grouting, vibro flotation, stone columns) are not covered by this European Standard. Bored piles are covered in EN 1536. Steel and timber sheet pile walls are covered in EN 12063. Micropiles are covered in EN 14199.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1537:2013(Main)
Execution of special geotechnical works - Ground anchors
SIST EN 1537:2013

1.1   This European Standard covers ground anchors grouted into the ground which are stressed and tested. They can be used for permanent or temporary applications.
NOTE   For the purpose of this standard the term ‘anchor(s)’ refers to ‘ground anchor(s)’.
1.2   The anchors are designed in accordance with EN 1997-1 and are tested in accordance with prEN ISO 22477 5.
1.3   Typical bond and compression type anchors are shown in Figure 1 and Figure 2.
1.4   The term "ground" is taken to encompass soil, rock and fill already in place or existing prior to the execution of the construction work.
1.5   The planning and design of ground anchors calls for experience and knowledge in this specialised field.
1.6   The installation and testing phases require skilled, qualified labour and supervision.
1.7   This standard cannot replace the knowledge of specialist personnel and the expertise of experienced contractors required to apply this standard.
1.8   This standard does not address systems such as tension piles, screw anchors, mechanical anchors, soil nails, dead-man anchors or expander anchors as these do not fulfil the requirements of this standard.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14490:2010(Main)
Execution of special geotechnical works - Soil nailing
SIST EN 14490:2010

1.1   This European Standard establishes general principles for the execution, testing, supervision and monitoring of soil nailing.
1.2   Soil nailing is a construction technique, used to enhance/maintain the stability of a soil mass by installation of reinforcing elements (soil nails). Typical examples of soil nailing are given in Annex A.
1.3   The scope of soil nailing applications considered in this European Standard includes the installation and testing of soil nails and associated operations, required when stabilising existing and newly cut slopes and faces in soil, existing earth retaining structures, embankments, existing tunnels and the excavated facing of new tunnels in soil.
1.4   Soil nailing may be used to form part of a hybrid construction. This European Standard is relevant only to the soil nailing aspect of such constructions.
1.5   Techniques, such as reinforcement of ground by vertical inclusions (sheet piles, bored or driven piles, or other elements) and stabilisation with rock bolts, prestressed ground anchors or tensions piles are not covered by this European Standard.
1.6   Guidance on practical aspects of soil nailing and aspects on design, durability and testing is given in informative Annexes A, B and C, respectively.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    76 pages
    German language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 15237:2007(Main)
Execution of special geotechnical works - Vertical drainage
SIST EN 15237:2007

This European Standard establishes general principles for the execution, testing, supervision and monitoring of vertical drain projects.
This European Standard includes the application of prefabricated vertical drains and sand drains and deals with requirements to be placed on design, drain material and installation methods. This European Standard applies to the improvement of low-permeability, highly compressible soils by vertical drainage and preloading. Information regarding loading (embankment, vacuum or ground water lowering) and preloading is given in informative Annexes A and B.
Vertical drainage is used both in on land and in marine constructions for the following purposes:
   (pre-)consolidation and reduction of post-construction settlements;
   speeding up the consolidation process by decreasing the path lengths for pore water dissipation;
   increase of stability (by increasing effective stresses in the soil);
   groundwater lowering;
   mitigation of liquefaction effects.
In each case there is an overall treatment of the soil (the volume of the drains is small in relation to the soil volume treated).
This European Standard does not include soil improvement by means of wells, gravel and stone columns, large-diameter geotextile enclosed columns or reinforcing elements.
Vertical drainage can also be combined with other foundation or ground improvement methods, e.g. electro osmosis, piles and compacted sand piles, dynamic compaction and deep mixing.
Guidance on practical aspects of vertical drainage, such as investigation of drain properties, execution procedures and equipment, is given in Annex A. Investigation of soil characteristics and assessment of design parameters, which are affected by drain properties and execution, are presented in Annex B.

  • Standard
    57 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14475:2006/AC:2006(Corrigendum)
Execution of special geotechnical works - Reinforced fill
SIST EN 14475:2006/AC:2007

TC - Modification to 6.3.2.2 and Table A.1

  • Corrigendum
    2 pages
    English and German language
    sale 10% off
    e-Library read for
    1 day