EN 13634:2015

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Varovalna obutev za voznike motornih koles - Zahteve in preskusne metodeSchutzschuhe für professionelle Motorradfahrer - Anforderungen und PrüfverfahrenChaussures de protection pour motocyclistes - Exigences et méthodes d'essaiProtective footwear for motorcycle riders - Requirements and test methods43.140Motorna kolesa in mopediMotor cycles and mopeds13.340.50Varovanje nog in stopalLeg and foot protectionICS:Ta slovenski standard je istoveten z:EN 13634:2015SIST EN 13634:2016en,fr,de01-februar-2016SIST EN 13634:2016SLOVENSKI
STANDARDSIST EN 13634:20111DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13634
December
t r s w ICS
s uä u v rä w r Supersedes EN
s u x u vã t r s rEnglish Version
Protective footwear for motorcycle riders æ Requirements and test methods Chaussures de protection pour motocyclistes æ Exigences et méthodes d 5essai
Schutzschuhe für Motorradfahrer æ Anforderungen und Prüfverfahren This European Standard was approved by CEN on
s r October
t r s wä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s w CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s u x u vã t r s w ESIST EN 13634:2016

Ergonomic and size testing . 24 A.1 Principle . 24 A.2 Assessors . 24 A.3 Procedure for footwear size verification . 24 A.4 Procedure for ergonomic evaluation . 24 Annex B (informative)
Uncertainty of measurement and interpretation of results . 26 B.1 Uncertainty of measurement . 26 B.2 Interpretation of results . 26 B.3 Calculation of uncertainty of measurement . 27 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC Personal Protective Equipment . 28 Bibliography . 30
in mm H1 (Figure 1)
in mm Paris Point UK
36 and below Up to 3½ 103 64 37 and 38 4 to 5 105 66 39 and 40 5½ to 6½ 109 68 41 and 42 7 to 8 113 70 43 and 44 8½ to 10 117 72 45 and above 10½ and above 121 73 Table 3 — Minimum height of high upper Footwear size H2 (Figure 1) in mm Paris Point UK
36 and below Up to 3½ 162 37 and 38 4 to 5 165 39 and 40 5½ to 6½ 172 41 and 42 7 to 8 178 43 and 44 8½ to 10 185 45 and above 10½ and above 192
Figure 1 — Footwear minimum upper height definition of H1 and H2 4.2.2 Whole upper Upper material shall meet the requirements of 4.4. SIST EN 13634:2016

Minimum abrasion resistance (in second) Areas (see Figure 2 and Table 6) Level 1 Level 2 A 1,5 s 2,5 s B 5 s 12 s Height of the upper At least the value given in Table 2 At least the value given in Table 3 Table 5 — Dimensions for Impact Zones and Material Areas shown in Figure 2 (Dimensions in millimetres) Size (Paris Points) Size (English) C D E r F G min. min. min. max. min. max. 38 and below 5 and below 70 45 80 17 40 120 39 to 42 5,5 to 8 75 50 90 19 50 125 43 and above 8,5 and above 80 55 95 21 55 130 SIST EN 13634:2016

Key 1 = zone 1 shin region 2 = zone 2 ankle region r radius curvature keys for C D E F G see Table 5
= Area A
= Area B Figure 2 — Impact zones and material areas (see Table 5) 4.4.5 Impact cut resistance When the full thickness of the upper (i.e. upper + lining) is tested in accordance with the procedure in EN 13595-4:2002, with 3 test pieces from each combination of material, the impact cut resistance of the upper shall be classified as below. All material type combinations shall be tested and the upper classified on the lowest result (see Table 6): SIST EN 13634:2016
...