EN 12697-6:2003+A1:2007
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 6: Determination of bulk density of bituminous specimens
Bituminous mixtures - Test methods for hot mix asphalt - Part 6: Determination of bulk density of bituminous specimens
This European Standard describes test methods for determining the bulk density of a compacted bituminous specimen. The test methods are intended for use with laboratory compacted specimens or specimens from cores cut from the pavement after placement and compacting.
This European Standard describes the following four procedures, the choice of which is used being dependent on the estimated content and accessibility of voids in the specimen:
a) bulk density - dry (for specimens with a very closed surface);
b) bulk density - saturated surface dry (SSD) (for specimens with a closed surface);
c) bulk density - sealed specimen (for specimens with an open or coarse surface);
d) bulk density by dimensions (for specimens with a regular surface and with geometric shapes, i. e. squares, rectangles, cylinders etc.
NOTE Annex A (informative) gives general guidance on selecting the appropriate procedure.
Asphalt - Prüfverfahren für Heißasphalt - Teil 6: Bestimmung der Raumdichte von Asphalt-Probekörpern
Diese Europäische Norm beschreibt Prüfverfahren zur Bestimmung der Raumdichte von verdichteten Asphalt-Probekörpern. Diese Prüfverfahren sind für die Anwendung auf im Labor verdichtete Probekörper oder aus Bohrkernen hergestellte Probekörper vorgesehen, die zuvor einer Fahrbahndecke nach deren Einbau und Verdichtung entnommen wurden.
Diese Europäische Norm beschreibt die folgenden vier Verfahren, wobei die Entscheidung, welches von diesen anzuwenden ist, vom geschätzten Hohlraumgehalt und von der Zugänglichkeit der Hohlräume im Probekörper abhängt:
a) Raumdichte trocken (für Probekörper mit einer sehr dichten Oberfläche);
b) Raumdichte gesättigte Oberfläche trocken (Saturated Surface Dry, SSD) (für Probekörper mit einer dichten Oberfläche);
c) Raumdichte umhüllter Probekörper (für Probekörper mit einer offenen oder rauen Oberfläche);
d) Raumdichte durch Ausmessen (für Probekörper mit einer regelmäßigen Oberfläche und geometrischen Formen, d. h. Quadrate, Rechtecke, Zylinder usw.).
ANMERKUNG Anhang A (informativ) enthält grundsätzliche Hinweise zur Auswahl des zutreffenden Prüfverfahrens.
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 6 : Détermination de la masse volumique apparente des éprouvettes bitumineuses
La présente Norme européenne décrit les méthodes d’essai pour la détermination de la masse volumique apparente de corps d’épreuve bitumineux après compactage. Les méthodes d’essai sont applicables à des éprouvettes compactées en laboratoire ou à des corps d’épreuve prélevés dans la chaussée après répandage et compactage.
La présente Norme européenne décrit quatre méthodes ci-après, le choix de chacune d’entre elles dépendant du volume de vides estimé et de leur accessibilité dans l’éprouvette :
a) masse volumique apparente sèche (pour les éprouvettes présentant une surface très fermée) ;
b) masse volumique apparente surface saturée sèche (SSS) (pour les éprouvettes présentant une surface fermée) ;
c) masse volumique apparente éprouvette « paraffinée » (pour les éprouvettes présentant une surface ouverte ou grossière) ;
d) masse volumique apparente géométrique (pour les éprouvettes présentant une surface régulière et des faces de formes géométriques carrées, rectangulaires, cylindriques, etc.).
NOTE L’Annexe A (informative) donne des indications générales sur le choix de la méthode appropriée.
Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 6. del: Ugotavljanje gostote bitumenskih preskušancev
General Information
- Status
- Withdrawn
- Publication Date
- 03-Jul-2007
- Withdrawal Date
- 24-Apr-2012
- Technical Committee
- CEN/TC 227 - Road materials
- Drafting Committee
- CEN/TC 227/WG 1 - Bituminous mixtures
- Current Stage
- 9960 - Withdrawal effective - Withdrawal
- Start Date
- 25-Apr-2012
- Completion Date
- 25-Apr-2012
- Directive
- 89/106/EEC - Construction products
Relations
- Effective Date
- 22-Dec-2008
- Effective Date
- 28-May-2011
Frequently Asked Questions
EN 12697-6:2003+A1:2007 is a standard published by the European Committee for Standardization (CEN). Its full title is "Bituminous mixtures - Test methods for hot mix asphalt - Part 6: Determination of bulk density of bituminous specimens". This standard covers: This European Standard describes test methods for determining the bulk density of a compacted bituminous specimen. The test methods are intended for use with laboratory compacted specimens or specimens from cores cut from the pavement after placement and compacting. This European Standard describes the following four procedures, the choice of which is used being dependent on the estimated content and accessibility of voids in the specimen: a) bulk density - dry (for specimens with a very closed surface); b) bulk density - saturated surface dry (SSD) (for specimens with a closed surface); c) bulk density - sealed specimen (for specimens with an open or coarse surface); d) bulk density by dimensions (for specimens with a regular surface and with geometric shapes, i. e. squares, rectangles, cylinders etc. NOTE Annex A (informative) gives general guidance on selecting the appropriate procedure.
This European Standard describes test methods for determining the bulk density of a compacted bituminous specimen. The test methods are intended for use with laboratory compacted specimens or specimens from cores cut from the pavement after placement and compacting. This European Standard describes the following four procedures, the choice of which is used being dependent on the estimated content and accessibility of voids in the specimen: a) bulk density - dry (for specimens with a very closed surface); b) bulk density - saturated surface dry (SSD) (for specimens with a closed surface); c) bulk density - sealed specimen (for specimens with an open or coarse surface); d) bulk density by dimensions (for specimens with a regular surface and with geometric shapes, i. e. squares, rectangles, cylinders etc. NOTE Annex A (informative) gives general guidance on selecting the appropriate procedure.
EN 12697-6:2003+A1:2007 is classified under the following ICS (International Classification for Standards) categories: 93.080.20 - Road construction materials. The ICS classification helps identify the subject area and facilitates finding related standards.
EN 12697-6:2003+A1:2007 has the following relationships with other standards: It is inter standard links to EN 12697-6:2003, EN 12697-6:2012. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
EN 12697-6:2003+A1:2007 is associated with the following European legislation: EU Directives/Regulations: 305/2011, 89/106/EEC. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
EN 12697-6:2003+A1:2007 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bituminous mixtures - Test methods for hot mix asphalt - Part 6: Determination of bulk density of bituminous specimensGHOMélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné a chaud - Partie 6 : Détermination de la masse volumique apparente des éprouvettes bitumineusesAsphalt - Prüfverfahren für Heißasphalt - Teil 6: Bestimmung der Raumdichte von Asphalt-ProbekörpernTa slovenski standard je istoveten z:EN 12697-6:2003+A1:2007SIST EN 12697-6:2004+A1:2007en,fr,de93.080.20Materiali za gradnjo cestRoad construction materialsICS:SLOVENSKI
STANDARDSIST EN 12697-6:2004+A1:200701-november-2007
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-6:2003+A1
July 2007 ICS 93.080.20 Supersedes EN 12697-6:2003English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 6: Determination of bulk density of bituminous specimens
Matériaux enrobés - Méthodes d'essai pour enrobés à chaud - Partie 6: Détermination de la masse volumique apparente des éprouvettes bitumineuses
Asphalt - Prüfverfahren für Heißasphalt - Teil 6: Bestimmung der Raumdichte von Asphalt-Probekörpern This European Standard was approved by CEN on 21 November 2002 and includes Amendment 1 approved by CEN on 16 May 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-6:2003+A1:2007: E
General guidance on selection of a test procedure to determine the bulk density of compacted bituminous materials.13 Bibliography.16
Table 1 — Water density Water temperature 0C Correction factor K Water density kg/m3 Water temperature 0C Correction factor K Water density kg/m3 10 11 12 13 14 15 16 17 18 19 20 1,0027 1,0026 1,0025 1,0023 1,0022 1,0021 1,0019 1,0017 1,0016 1,0014 1,0012 999,8 999,7 999,6 999,4 999,3 999,2 999,0 998,8 998,7 998,5 998,3 20 21 22 23 24 25 26 27 28 29 30 1,0012 1,0010 1,0007 1,0005 1,0003 1,0000 0,9997 0,9995 0,9992 0,9989 0,9986 998,3 998,1 997,8 997,6 997,4 997,1 996,8 996,6 996,3 996,0 995,7
5.2 Additional materials for the sealed specimen procedure Material to seal the specimen, in such a way, that inclusion of voids (being no part of the specimen) between seal and specimen is prevented. The density of the sealing material at test temperature shall be known to the nearest 0,010 g/cm3. NOTE The material used can be paraffin wax, shrinkage foil, latex emulsion etc. The procedure to apply such materials should be such that the specimen is not damaged. It is very important that the seal exactly covers the specimen including the voids which technologically form part of its volume: when applying the seal penetration of the internal voids belonging to the material is prevented, as well as inclusion of extra voids between seal and specimen or in seal folds. 6 Apparatus
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...