EN 14354:2017
(Main)Wood-based panels - Wood veneer floor coverings
Wood-based panels - Wood veneer floor coverings
This European Standard defines terms and specifies requirements and test methods for wood veneer floor coverings with multilayer built up for internal use. It gives guidance for the evaluation of conformity of the products to the requirements of this standard.
This European Standard is not applicable to multilayer parquet elements with a minimum top layer thickness of 2,5 mm. For these products EN 13489 applies.
Holzwerkstoffe - Furnierte Fußbodenbeläge
Diese Europäische Norm definiert Benennungen und legt Anforderungen und Prüfverfahren für furnierte, mehrschichtig aufgebaute Fußbodenbeläge zur Verwendung im Innenbereich fest. Es gibt eine Anleitung zur Konformitätsbewertung der Produkte in Bezug auf die Anforderungen dieser Norm.
Diese Europäische Norm ist nicht anwendbar auf Mehrschichtparkettelemente mit einer Deckschichtdicke von mindestens 2,5 mm. Für diese Produkte gilt EN 13489.
Panneaux à base de bois - Revêtements de sol à placage bois
La présente Norme européenne définit les termes et spécifie les exigences ainsi que les méthodes d’essai des revêtements de sol à placage bois ayant une structure multicouche pour usage intérieur. Elle fournit des préconisations pour l’évaluation de la conformité des produits au regard des exigences de la présente norme.
La présente Norme européenne ne s’applique pas aux éléments de parquet multicouche dont le parement présente une épaisseur supérieure ou égale à 2,5 mm. Pour ces produits, l’EN 13489 s’applique.
Lesne plošče - Furnirane talne obloge
Ta dokument določa definicije, zahteve in preskusne metode za furnirane talne obloge za notranjo uporabo. Podaja smernice za vrednotenje skladnosti izdelkov z zahtevami tega standarda. Furnirane talne obloge brez obdelave so izključene.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Holzwerkstoffe - Furnierte FußbodenbelägePanneaux à base de bois - Revêtements de sol à placage boisWood-based panels - Wood veneer floor coverings97.150Talne oblogeFloor coverings79.080Polizdelki iz lesaSemi-manufactures of timberICS:Ta slovenski standard je istoveten z:EN 14354:2017SIST EN 14354:2017en,fr,de01-december-2017SIST EN 14354:2017SLOVENSKI
STANDARDSIST EN 14354:2005/AC:2007SIST EN 14354:20051DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14354
July
t r s y ICS
y {ä r z r Supersedes EN
s v u w vã t r r vEnglish Version
Woodæbased panels æ Wood veneer floor coverings Panneaux à base de bois æ Revêtements de sol à placage bois
Holzwerkstoffe æ Furnierte Fußbodenbeläge This European Standard was approved by CEN on
t y February
t r s yä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v u w vã t r s y ESIST EN 14354:2017
Contents Page European foreword . 5 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 4 Requirements . 8 4.1 General . 8 4.2 General requirements . 8 5 Classification requirements . 9 5.1 General . 9 5.2 Classification requirements for elements with lacquered surfaces . 10 6 Marking and packaging . 10 6.1 Marking . 10 6.2 Packaging . 11 7 Test report . 11 Annex A (normative)
Determination of thickness, length, width, squareness, deviation from edge straightness and cup . 12 A.1 General . 12 A.2 Sampling . 12 A.3 Conditioning . 12 A.4 Test equipment . 12 A.5 Procedure. 13 A.5.1 Determination of thickness t . 13 A.5.2 Determination of length l . 14 A.5.3 Determination of width w and dimensions of squared elements . 14 A.5.4 Determination of deviation from squareness q . 15 A.5.5 Determination of deviation of edge straightness s . 15 A.5.6 Determination of cup fw . 16 A.6 Calculation and expression of results . 16 A.6.1 Thickness t . 16 A.6.2 Width w . 16 A.6.3 Length l. 16 A.6.4 Deviation from squareness q . 16 A.6.5 Deviation from edge straightness s . 16 A.6.6 Cup fw . 17 A.7 Test report . 17 SIST EN 14354:2017
Annex B (normative)
Determination of opening and lipping between elements . 18 B.1 General . 18 B.2 Sampling . 18 B.3 Conditioning . 18 B.4 Test equipment . 18 B.5 Procedure . 18 B.5.1 Assembling . 18 B.5.2 Measuring of lipping . 19 B.5.3 Measuring of openings . 19 B.5.4 Calculation and expression of results . 19 B.6 Test report . 19 Annex C (normative)
Determination of the elasticity of lacquer. 20 C.1 General . 20 C.2 Sampling . 20 C.3 Apparatus . 20 C.4 Procedure . 20 C.5 Calculation and expression of results . 20 C.6 Evaluation of results, elasticity classification . 20 Annex D (normative)
Determination of the wear resistance using the falling sand method . 21 D.1 General . 21 D.2 Sampling . 21 D.3 Conditioning . 21 D.4 Apparatus . 22 D.4.1 Testing machine . 22 D.4.2 Grit feeder and accessories . 22 D.4.3 Additional material or equipment . 27 D.5 Procedure . 27 D.5.1 General . 27 D.5.2 Maintenance of the abrading wheels . 27 D.5.3 Operation of the abrader . 27 D.5.4 Calibration . 28 D.5.5 Abrasion of test specimen . 29 D.6 Expression of results . 30 D.7 Test report . 30 Annex E (normative)
Determination of abrasion resistance using the sand paper method . 31 E.1 General . 31 SIST EN 14354:2017
E.2 Sampling . 31 E.3 Conditioning . 31 E.4 Apparatus . 32 E.4.1 Testing machine . 32 E.4.2 Additional material or equipment . 35 E.5 Procedure. 35 E.5.1 General . 35 E.5.2 Preparation of test specimens and abrasive papers . 36 E.5.3 Preparation of abrasive wheels . 36 E.5.4 Determination of the abrasion rate of abrasive paper .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.