prEN ISO 15027-1

SLOVENSKI STANDARD
01-julij-2023
Potopne obleke - 1. del: Stalno nošene obleke, zahteve, vključno z varnostjo
(ISO/DIS 15027-1:2023)
Immersion suits - Part 1: Constant wear suits, requirements including safety (ISO/DIS
15027-1:2023)
Schutzkleidung gegen Unterkühlung im Wasser - Teil 1: Kälteschutzanzüge,
Anforderungen einschließlich Sicherheit (ISO/DIS 15027-1:2023)
Combinaisons de protection thermique en cas d'immersion - Partie 1: Combinaisons de
port permanent, exigences, y compris la sécurité (ISO/DIS 15027-1:2023)
Ta slovenski standard je istoveten z: prEN ISO 15027-1
ICS:
13.340.10 Varovalna obleka Protective clothing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 15027-1
ISO/TC 188/SC 1 Secretariat: AFNOR
Voting begins on: Voting terminates on:
2023-05-03 2023-07-26
Immersion suits —
Part 1:
Constant wear suits, requirements including safety
Combinaisons de protection thermique en cas d'immersion —
Partie 1: Combinaisons de port permanent, exigences, y compris la sécurité
ICS: 13.340.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 15027-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 15027-1:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 15027-1
ISO/TC 188/SC 1 Secretariat: AFNOR
Voting begins on: Voting terminates on:

Immersion suits —
Part 1:
Constant wear suits, requirements including safety
Combinaisons de protection thermique en cas d'immersion —
Partie 1: Combinaisons de port permanent, exigences, y compris la sécurité
ICS: 13.340.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 15027-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 15027-1:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements . 4
4.1 General . 4
4.2 Basic health and ergonomic requirements . 5
4.2.1 Innocuousness . 5
4.2.2 Design . 5
4.2.3 Comfort . 5
4.3 Other optional accessories . 5
4.4 Gas or air inflation . . 6
4.5 Buddy lines . 6
4.6 Conspicuity . 6
4.6.1 Colour . 6
4.6.2 Retro-reflective material . 7
4.6.3 Emergency position-indicating-lights . 8
4.7 Foam flotation material . 8
4.8 Flammability . 8
4.9 Temperature cycling . . 8
4.10 Leakage . 8
4.11 Thermal protection in water . 8
4.12 Performance requirements . 9
4.12.1 Donning . 9
4.12.2 Walking . 9
4.12.3 Climbing . 9
4.12.4 Dexterity and mobility . 10
4.12.5 Hand protection . 10
4.12.6 Jump test . 10
4.12.7 Secondary donning . . 10
4.12.8 Swim and boarding . 10
4.12.9 Flotation and righting . 10
4.12.10 Field of vision. 10
4.12.11 Helicopter escape . 11
4.13 Requirements on materials, fabrics and components . 11
4.13.1 Fuel resistance . 11
4.13.2 Resistance to illumination . 11
4.13.3 Tensile strength of seams . 11
4.13.4 Coated fabrics. 11
4.13.5 Other fabrics . 12
4.13.6 Thermal insulation identification .12
4.13.7 Metal components .12
4.14 Strength .12
5 Marking . .12
6 Information supplied by the manufacturer .13
7 Consumer information at point of sale .14
7.1 Data list . 14
7.2 Consumer information label . 14
iii
ISO/DIS 15027-1:2023(E)
Annex A (informative) Guidelines for manufacturers, users, regulators and industrial
inspectors about immersion suits with respect to the application of thermal
protection times relevant to the ISO 15027 series .16
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Regulation 2016/425 aimed to be covered .19
iv
ISO/DIS 15027-1:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represent
...