EN 1514-2:2005
(Main)Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
This European standard specifies the dimensions and marking of spiral wound gaskets for use in conjunction with flat face and raised face flanges complying with EN 1092-1 for PN 10, PN 16, PN 25, PN 40, PN 63 and PN 100 and up to and including DN 900.
NOTE 1 Dimensions of other types of gaskets for use with flanges to EN 1092-1, EN 1092-2, prEN 1092-3 and EN 1092-4 are given in EN 1514-1, EN 1514-3, EN 1514-4, prEN 1514-6, prEN 1514-7 and prEN 1514-8.
NOTE 2 Annex A lists information that should be supplied by the purchaser when ordering gaskets in circumstances where the choice of the gasket materials appropriate to the service is left to the supplier.
Flansche und ihre Verbindungen - Dichtungen für Flansche mit PN-Bezeichnung - Teil 2: Spiraldichtungen für Stahlflansche
Diese Europäische Norm legt die Maße und Kennzeichnung von Spiraldichtungen zur Verwendung mit
Flanschen mit glatter Dichtfläche (ohne Dichtleiste) und Flanschen mit Dichtleiste nach EN 1092-1 für PN 10,
PN 16, PN 25, PN 40, PN 63, PN 100 und PN 160 und Nennweiten bis einschließlich DN 1000 fest.
ANMERKUNG 1 Die Maße für andere Dichtungsformen für die Verwendung mit Flanschen nach EN 1092-1,
EN 1092-2, EN 1092-3 und EN 1092-4 sind in EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 und EN 1514-8
enthalten.
ANMERKUNG 2 Anhang A enthält Angaben, die der Anwender bei der Bestellung von Dichtungen machen sollte, wenn
die Auswahl der für den Anwendungsfall geeigneten Dichtungswerkstoffe dem Lieferer überlassen bleibt.
Brides et leurs assemblages - Joints pour les brides désignées PN - Partie 2: Joints spiralés pour utilisation avec des brides en acier
La présente Norme européenne spécifie les dimensions et le marquage des joints spiralés utilisés
conjointement avec les brides à face plate et surélevée conformes à l�EN 1092-1, pour les pressions
nominales PN 10, PN 16, PN 25, PN 40, PN 63, PN 100 et PN 160 et les diamètres nominaux jusqu�à
DN 1000 inclus.
NOTE 1 Les dimensions des autres types de joints utilisés avec des brides conformes aux EN 1092-1, EN 1092-2,
EN 1092-3 et EN 1092-4 sont données dans les EN 1514-1, EN 1514-3, EN 1514-4, EN 1514-6, EN 1514-7 et EN 1514-8.
NOTE 2 L'Annexe A liste les informations que l'acheteur peut fournir lors de sa commande de joints lorsque le choix
des matériaux de joint appropriés à l�utilisation est laissé au fournisseur.
Prirobnice in prirobnični spoji - Tesnila za prirobnice z oznako PN - 2. del: Spiralna tesnila za jeklene prirobnice
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Flansche und ihre Verbindungen - Dichtungen für Flansche mit PN-Bezeichnung - Teil 2: Spiraldichtungen für StahlflanscheBrides et leurs assemblages - Joints pour les brides désignées PN - Partie 2: Joints spiralés pour utilisation avec des brides en acierFlanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges23.040.80Tesnila za cevne zvezeSeals for pipe and hose assemblies23.040.60Prirobnice, oglavki in spojni elementiFlanges, couplings and jointsICS:Ta slovenski standard je istoveten z:EN 1514-2:2005SIST EN 1514-2:2005en01-julij-2005SIST EN 1514-2:2005SLOVENSKI
STANDARDSIST EN 1514-2:19981DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1514-2
May 2005 ICS 23.040.80 Supersedes EN 1514-2:1997 English version
Flanges and their joints - Gaskets for PN-designated flanges - Part 2: Spiral wound gaskets for use with steel flanges
Brides et leurs assemblages - Joints pour les brides désignées PN - Partie 2: Joints spiralés pour utilisation avec des brides en acier
Flansche und ihre Verbindungen - Dichtungen für Flansche mit PN-Bezeichnung - Teil 2: Spiraldichtungen für Stahlflansche This European Standard was approved by CEN on 24 March 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2005 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1514-2:2005: ESIST EN 1514-2:2005
Information to be supplied by the purchaser.13 Bibliography.14
The essential features of a spiral wound gasket in compliance with this specification are given in Figures 1 and 2 and/or are listed below. Movement of centre of inner ring relative to guide ring Up to DN 200 a maximum of 0,2 mm
Above DN 200 a maximum of 0,4 mm Guide Ring Thickness 3 mm ± 0,25 SIST EN 1514-2:2005
Centre ± 0,1 mm Number of empty wraps on external diameter of the sealing 3 to 5 element Number of empty wraps on the internal diameter of the sealing 2 to 3 element Number of welds on the inner and outer diameters of the sealing Minimum of 4 element, i.e. on the empty wraps Thickness of the metal of the sealing element 0,2 mm ± 0,02 mm Width of the profiled metal of the sealing element 4,5 mm 300.+ Thickness of the filler material shall be as appropriate for the filler type
Protrusion of the filler above the profiled metal of the sealing 0,3 ± 0,1 mm element Compression of the sealing element shall not result in contact between the flange and the guide ring, see also 4.1.2 Graphite ash content maximum of 2 % PTFE filler to contain no recycled material and may be either sintered or non-sintered Sharp edges on inner ring and guide ring to be removed Dimensions to be as given in Table 1 4.1.2 Maximum Compression Metal to metal contact between the guide ring and the flange shall not be achieved with the maximum load th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.