Packaging - Rigid plastic containers - PET finish 29/25 (12,6)

This document specifies the design and dimensions of the 29 mm screw finish with three (3) thread starts for flat waters and non-carbonated beverages.
This document applies to finishes designated as PET finishes 29/25 (12,6). The dimension (12,6) is the height in millimetres from the top of finish to the bottom of the support ledge.
This finish can be used for aseptic filling and filling which utilizes nitrogen pressure where the internal overpressure does not exceed 1 bar maximum.
This finish is designed to accept only a tamper evident plastic closure, including those with an attachment feature.

Verpackung - Formstabile Kunststoffbehälter - PET-Verschlussmundstück 29/25 (12,6)

Dieses Dokument legt die Konstruktion und die Maße für ein 29 mm-Schraubverschlussmundstück mit drei (3) Gewindegängen für stilles Wasser und kohlensäurefreie Getränke fest.
Dieses Dokument gilt für Verschlussmundstücke als PET-Verschlussmundstücke 29/25 (12,6). Das Maß (12,6) ist die Höhe, in Millimeter, von der Oberkante des Verschlussmundstückes bis zur Unterseite des Halsstützrings.
Dieses Verschlussmundstück kann zur aseptischen Befüllung und zur Befüllung mithilfe von Stickstoffdruck verwendet werden, wobei der innere Überdruck 1 bar nicht überschreiten darf.
Dieses Verschlussmundstück ist dafür ausgelegt, ausschließlich Kunststoffverschlüsse mit Originalitäts-sicherung einschließlich Varianten mit Anbindungselement aufzunehmen.

Emballage - Récipients en plastique rigide - Bague PET 29/25 (12,6)

Le présent document spécifie la conception et les dimensions de la bague à vis de 29 mm à trois (3) filets pour le bouchage des eaux plates et des boissons non carbonatées.
Il est applicable aux bagues désignées « bagues PET 29/25 (12,6) ». La dimension (12,6) est la hauteur, en millimètres, entre le sommet de la bague et le bas de la collerette de préhension.
La bague peut être utilisée pour le remplissage aseptique et pour le remplissage avec utilisation d’azote sous pression, la surpression interne n’excédant pas 1 bar.
Cette bague est prévue pour recevoir uniquement une capsule en plastique avec témoin d’effraction, y compris une capsule restant attachée à la bouteille lors de l’utilisation.

Embalaža - Toge plastične posode - PET-grla 29/25 (12,6)

Ta evropski standard določa zasnovo in mere za navojno grlo s premerom 29 mm ter trojnim (3) začetkom navoja za negazirano vodo in negazirane napitke. To grlo je namensko grlo PET 29/25 (12,6).
To grlo je mogoče uporabljati za aseptično polnjenje in polnjenje z dodajanjem dušika (notranji nadtlak nižji od največ 1 bara). Mera (12,6) je višina v milimetrih od vrha grla do dna podpornega okrajka.
Grlu se lahko doda le plastičen čep, ki varuje pred nedovoljenim odpiranjem. Pri prvem odpiranju se obroček, ki varuje pred nedovoljenim odpiranjem, loči od lupine čepa in ostane na grlu steklenice ali pa se, kot pri povratnih steklenicah, pretrga, vendar ostane pritrjen na lupino čepa.

General Information

Status
Published
Publication Date
25-Oct-2022
Current Stage
6562 - Completion of withdrawal of conflicting national standards (DOW) - Implementation
Start Date
30-Apr-2023
Due Date
08-Nov-2023
Completion Date
30-Apr-2023

Relations

Buy Standard

Standard
EN 16592:2023
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-januar-2023
Nadomešča:
SIST EN 16592:2015
Embalaža - Toge plastične posode - PET-grla 29/25 (12,6)
Packaging - Rigid plastic containers - PET finish 29/25 (12,6)
Verpackung - Formstabile Kunststoffbehälter - PET-Verschlussmundstück 29/25 (12,6)
Emballage - Récipients en plastique rigide - Bague PET 29/25 (12,6)
Ta slovenski standard je istoveten z: EN 16592:2022
ICS:
55.100 Steklenice. Lonci. Kozarci Bottles. Pots. Jars
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 16592
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2022
EUROPÄISCHE NORM
ICS 55.100 Supersedes EN 16592:2014
English Version
Packaging - Rigid plastic containers - PET finish 29/25
(12,6)
Emballage - Récipients en plastique rigide - Bague PET Verpackung - Formstabile Kunststoffbehälter - PET-
29/25 (12,6) Verschlussmundstück 29/25 (12,6)
This European Standard was approved by CEN on 19 September 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16592:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Dimensions. 5
5 Requirements . 6
Bibliography . 8

European foreword
This document (EN 16592:2022) has been prepared by Technical Committee CEN/TC 261 “Packaging”,
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2023, and conflicting national standards shall be
withdrawn at the latest by April 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 16592:2014.
In comparison with the previous edition, the following technical modifications have been made:
— the explanations about the tamper evident feature have been removed from the scope;
— the possibility of having an attached cap is now mentioned;
— in Figure 1: removal from the tolerance on the neck diameter Ø28.00, the dimension is now
indicated Ø (28.00); a straight cylindrical zone of 3,50 mm is indicated unde
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.