Protective clothing for automobile racing drivers - Protection against heat and flame - Performance requirements and test methods (ISO/DIS 14460:2023)

Schutzkleidung für Auto Rennfahrer - Schutz gegen Hitze und Feuer - Leistungsanforderungen und Prüfverfahren (ISO/DIS 14460:2023)

Habillement de protection pour pilotes automobiles - Protection contre la chaleur et les flammes - Exigences de performance et méthodes d'essai (ISO/DIS 14460:2023)

La présente Norme internationale spécifie les méthodes d'essai, les exigences de performance et les paramètres de conception des vêtements de protection contre la chaleur et le feu destinés à être portés par les pilotes automobiles lors des compétitions. La présente Norme internationale couvre les vêtements de dessus et de dessous, les chaussettes, les gants et les cagoules; elle ne couvre pas les chaussures et les casques.

Varovalna obleka za voznike dirkalnih avtomobilov - Zaščita pred učinki toplote in plamena - Zahtevane lastnosti in preskusne metode (ISO/DIS 14460:2023)

General Information

Status
Not Published
Publication Date
15-Jun-2025
Current Stage
4599 - Dispatch of FV draft to CMC - Finalization for Vote
Start Date
11-Oct-2024
Completion Date
11-Oct-2024

Relations

Buy Standard

Draft
prEN ISO 14460:2023
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-april-2023
Nadomešča:
SIST EN ISO 14460:2000
SIST EN ISO 14460:2000/A1:2002
Varovalna obleka za voznike dirkalnih avtomobilov - Zaščita pred učinki toplote in
plamena - Zahtevane lastnosti in preskusne metode (ISO/DIS 14460:2023)
Protective clothing for automobile racing drivers - Protection against heat and flame -
Performance requirements and test methods (ISO/DIS 14460:2023)
Schutzkleidung für Auto Rennfahrer - Schutz gegen Hitze und Feuer -
Leistungsanforderungen und Prüfverfahren (ISO/DIS 14460:2023)
Habillement de protection pour pilotes automobiles - Protection contre la chaleur et les
flammes - Exigences de performance et méthodes d'essai (ISO/DIS 14460:2023)
Ta slovenski standard je istoveten z: prEN ISO 14460
ICS:
13.340.10 Varovalna obleka Protective clothing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 14460
ISO/TC 94/SC 13 Secretariat: SNV
Voting begins on: Voting terminates on:
2023-01-25 2023-04-19
Protective clothing for automobile racing drivers —
Protection against heat and flame — Performance
requirements and test methods
Vêtements de protection pour pilotes automobiles — Protection contre la chaleur et le feu — Exigences de
performance et méthodes d'essai
ICS: 97.220.40; 13.340.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 14460:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 14460:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14460
ISO/TC 94/SC 13 Secretariat: SNV
Voting begins on: Voting terminates on:

Protective clothing for automobile racing drivers —
Protection against heat and flame — Performance
requirements and test methods
Vêtements de protection pour pilotes automobiles — Protection contre la chaleur et le feu — Exigences de
performance et méthodes d'essai
ICS: 97.220.40; 13.340.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 14460:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022

ISO/DIS 14460:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Design . 2
4.1 General . 2
4.2 Garments. 3
4.2.1 General . 3
4.2.2 Outer Garments . 3
4.2.3 Pockets and closures of outer garment . 3
4.2.4 Under garments . 4
4.2.5 Balaclava . 4
4.2.6 Socks. 4
4.2.7 Gloves . 4
5 Sampling and pre-treatment . .4
6 Testing. 5
6.1 Limited flame spread . 5
6.2 Convective heat . 5
6.2.1 Heat test . 5
6.2.2 Mechanical resistance after convective heat . 6
6.3 Heat resistance at a temperature . 6
6.4 The mechanical resistance of component assemblies after exposure to flame shall
be tested in accordance with the following test. . 6
6.5 Dimensional change of textile materials . 7
6.6 Tensile Strength of structural seams . 7
7 Marking . . 8
7.1 General . 8
7.2 Marking, specific. 8
7.3 Marking,. 8
8 Information supplied by the manufacturer . 8
Annex A (informative) Information for users . 9
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of EU Regulation 2016/425 of the European Parliament and of the
Council of 9 March 2016 on personal protective equipment aimed to be covered .10
iii
ISO/DIS 14460:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 94, Personal safety — Personal protective
equipment, Subcommittee SC 13, Protective clothing.
The intent of this document is to provide a standard for drivers of automobiles that do not fall within
the scope of the FIA. The intent is to provide a similar level of protection as FIA 8856.
This second edition cancels and replaces the first edition (ISO 14460:1999), which has been technically
revised.
The main changes are as follows:
— Terms and Definition, added new CEN & ISO Documents
— Normative references updated
— Annex ZA updated
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
DRAFT INTERNATIONAL STANDARD ISO/DIS 14460:2022(E)
Protective clothing for automobile racing drivers —
Protection against heat and flame — Performance
requirements and test methods
1 Scope
This document specifies test methods, performance requirements and design parameters for clothing
for protection against heat and flame intended for drivers in automobile competitions. This document
concerns outer garments, under garments, socks, gloves and balaclava. Shoes and helmets are excluded.
The intent of this is to provide a standard for drivers of automobiles that do not fall within the scope of
the FIA. The intent is to provide a similar level of protection as FIA 8856
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3175-1:2017, Textiles — Dry-cleaning and finishing — Part 1: Method for assessing the cleanability of
textiles and garments
ISO 3758:2012, Textiles — Care labelling code using symbols
ISO 4675:2017, Rubber- or plastics-coated fab
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.