prEN ISO 20957-1

SLOVENSKI STANDARD
01-februar-2024
Nadomešča:
SIST EN ISO 20957-1:2013
Nepremična oprema za vadbo - 1. del: Splošne varnostne zahteve in preskusne
metode (ISO/DIS 20957-1:2023)
Stationary training equipment - Part 1: General safety requirements and test methods
(ISO/DIS 20957-1:2023)
Stationäre Trainingsgeräte - Teil 1: Allgemeine sicherheitstechnische Anforderungen und
Prüfverfahren (ISO/DIS 20957-1:2023)
Équipement d'entraînement fixe - Partie 1: Exigences générales de sécurité et méthodes
d'essai (ISO/DIS 20957-1:2023)
Ta slovenski standard je istoveten z: prEN ISO 20957-1
ICS:
97.220.30 Oprema za dvoranske športe Indoor sports equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT INTERNATIONAL STANDARD
ISO/DIS 20957-1
ISO/TC 83 Secretariat: DIN
Voting begins on: Voting terminates on:
2023-11-28 2024-02-20
Stationary training equipment —
Part 1:
General safety requirements and test methods
Équipement d'entraînement fixe —
Partie 1: Exigences générales de sécurité et méthodes d'essai
ICS: 97.220.30
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 20957-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 20957-1:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 20957-1
ISO/TC 83 Secretariat: DIN
Voting begins on: Voting terminates on:

Stationary training equipment —
Part 1:
General safety requirements and test methods
Équipement d'entraînement fixe —
Partie 1: Exigences générales de sécurité et méthodes d'essai
ICS: 97.220.30
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 20957-1:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023

ISO/DIS 20957-1:2023(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Classification . 4
4.1 General . 4
4.2 Accuracy classes. 4
4.3 Usage classes . 4
5 Safety requirements. 4
5.1 General . 4
5.2 Stability . 5
5.3 External construction . 5
5.3.1 General . 5
5.3.2 Edges and corners . 5
5.3.3 Tube ends . 5
5.3.4 Squeeze and shear points . 5
5.3.5 Weights and other resistance means . 6
5.4 Entrapment of the user . 6
5.5 Adjustment components and locking mechanisms. 6
5.6 Ropes, belts, chains and attachment components . 6
5.6.1 General . 6
5.6.2 Ropes and belts . 6
5.6.3 Rope and belt guides . 7
5.7 Pull-in points . 7
5.8 Hand grips . 7
5.8.1 Integral handgrips . 7
5.8.2 Applied handgrips . 7
5.8.3 Rotating handgrips . 7
5.9 Endurance . 7
5.10 Isometric test function . 8
5.11 Heart rate measurement system . 8
5.11.1 Indication . 8
5.11.2 Heart rate control mode . 8
5.12 Electrical safety . 8
5.13 Loading . 8
5.14 Care and maintenance . 9
5.15 Assembly instructions . 9
5.16 General instructions for use . 9
5.17 Marking . 10
5.17.1 Permanent marking . 10
5.17.2 Additional marking . 11
6 Test methods .11
6.1 Test conditions . 11
6.2 Stability test . 11
6.2.1 Test in training position . . 11
6.2.2 Test in folded/storage position . 11
6.3 External construction . 11
6.3.1 Test of edges and corners . 11
6.3.2 Tube ends . 11
6.3.3 Testing of squeeze points and shear points.12
6.3.4 Weights and other resistant means .12
iii
ISO/DIS 20957-1:2023(E)
6.3.5 Testing of pull-in points .12
6.4 Testing of entrapment .12
6.5 Adjustment components and locking mechanisms.
...