EN 2402:2014
(Main)Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D ≤ 10 mm
Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D ≤ 10 mm
This European Standard specifies the requirements relating to: Heat resisting nickel base alloy NiCr20Co3Fe3 Annealed Wire D ≤ 10 mm
for aerospace applications.
NOTE Other designation: Only the chemical composition of this standard must be considered.
Luft- und Raumfahrt - Hochwarmfeste Nickelbasislegierung NiCr20Co3Fe3 - Geglüht - Draht - D ≤ 10 mm
Diese Norm legt die Anforderungen an
Hochwarmfeste Nickelbasislegierung NiCr20Co3Fe3
Geglüht
Draht D ≤ 10 mm
zur Anwendung in der Luft- und Raumfahrt fest.
ANMERKUNG Weitere übliche Bezeichnungen:
Es muss nur die chemische Zusammensetzung dieser Norm beachtet werden.
Série aérospatiale - Alliage résistant à base de nickel NiCr20Co3Fe3 - Requit - Fil - D ≤ 10 mm
Aeronavtika - Toplotnoodporna zlitina na osnovi niklja NiCr20Co3Fe3 - Žarjena - Žica - D ≤ 10 mm
EN 2402 določa zahteve glede: žarjene žice D ≤ 10 mm iz toplotnoodporne zlitine na osnovi niklja NiCr20Co3Fe3 za uporabo v aeronavtiki.
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.49.025.15Neželezove zlitine na splošnoNon-ferrous alloys in generalICS:Ta slovenski standard je istoveten z:EN 2402:2014SIST EN 2402:2014en,fr,de01-julij-2014SIST EN 2402:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 2402
April 2014 ICS 49.025.15 English Version
Aerospace series - Heat resisting nickel base alloy NiCr20Co3Fe3 - Annealed - Wire - D ≤ 10 mm
Série aérospatiale - Alliage résistant à base de nickel NiCr20Co3Fe3 - Requit - Fil - D ≤ 10 mm
Luft- und Raumfahrt - Hochwarmfeste Nickelbasislegierung NiCr20Co3Fe3 - Geglüht - Draht - D ≤ 10 mm This European Standard was approved by CEN on 27 December 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 2402:2014 ESIST EN 2402:2014
Page coreword .3 Introduction .4 1 Scope .5 2 kormative references .5 SIST EN 2402:2014
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.