prEN ISO 14344
(Main)Welding consumables - Procurement of filler materials and fluxes (ISO/DIS 14344:2024)
Welding consumables - Procurement of filler materials and fluxes (ISO/DIS 14344:2024)
ISO 14344:2010 specifies tools for communication between a purchaser and a supplier of welding consumables within quality systems, such as those based upon ISO 9001.
In production, the components of welding consumables are divided into discrete, predetermined quantities so that satisfactory tests with a sample from that quantity will establish that the entire quantity meets specification requirements. These quantities, known by such terms as heats, lots, blends, batches and mixes, vary in size according to the manufacturer. For identification purposes, each manufacturer assigns a unique designation to each quantity. This designation usually consists of a series of numbers or letters, or combinations thereof, which will enable the manufacturer to determine the date and time (or shift) of manufacture, the type and source of the raw materials used, and the details of the procedures used in producing the welding consumable. This designation stays with the welding consumable and can be used to identify the material later, in those cases in which identification is necessary.
ISO 14344:2010, together with an applicable International Standard or other standard for welding consumables, provides a method for preparing those specific details needed for welding consumable procurement which consist of: a) the welding consumable classification (selected from the applicable International Standard or other standard for welding consumables); b) the lot classification; c) the testing schedule.
Selection of the specific welding consumable classification, lot classification, and testing schedule depends upon the requirements of the application for which the welding consumable is being procured.
ISO 14344:2010 does not apply to non-consumable electrodes or shielding gases.
Schweißzusätze - Beschaffung von Schweißzusätzen (ISO/DIS 14344:2024)
Produits consommables pour le soudage - Approvisionnement en matériaux d'apport et flux (ISO/DIS 14344:2024)
L'ISO 14344:2010 spécifie un outil de communication entre un acheteur et un fournisseur de produits consommables pour le soudage dans le cadre de systèmes qualité, tels que ceux basés sur l'ISO 9001.
En production, les constituants des produits consommables pour le soudage sont divisés en grandeurs discrètes et prédéterminées, de sorte que des essais ou contrôles satisfaisants, sur un échantillon prélevé sur une quantité donnée, prouvent que toute la grandeur satisfait aux exigences de la spécification. Ces grandeurs, désignées sous le nom de coulées, lots, mélanges et charges, ont des dimensions qui varient selon le fabricant. Á des fins d'identification, chaque fabricant attribue une désignation unique à chaque grandeur. Cette désignation est généralement constituée d'une série de chiffres ou de lettres, ou d'une combinaison alphanumérique, qui permet au fabricant de déterminer la date et l'heure (ou l'équipe) de fabrication, le type et la source des matières premières utilisées, et les détails sur les méthodes utilisées pour fabriquer le produit consommable pour le soudage. Cette désignation accompagne le produit consommable pour le soudage et peut être utilisée pour identifier ultérieurement le matériau, dans les cas où l'identification est nécessaire.
L'ISO 14344:2010, combinée à une Norme internationale ou à une autre norme applicable de produits consommables pour le soudage, fournit une méthode permettant de mettre au point les détails spécifiques nécessaires à l'approvisionnement en produits consommables pour le soudage et comportant les aspects suivants: a) la classification des produits consommables pour le soudage (choisie d'après la Norme internationale ou une autre norme applicable de produits consommables); b) la classification des lots; c) le programme de contrôle.
Le choix de la classification spécifique des produits consommables pour le soudage, de la classification des lots et du programme de contrôle dépend des exigences de l'application à laquelle le produit consommable est destiné.
L'ISO 14344:2010 ne s'applique pas aux électrodes non consommables ou aux gaz de protection.
Dodajni in potrošni materiali za varjenje - Nabava dodajnih materialov in praškov (ISO/DIS 14344:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2024
Dodajni in potrošni materiali za varjenje - Nabava dodajnih materialov in praškov
(ISO/DIS 14344:2024)
Welding consumables - Procurement of filler materials and fluxes (ISO/DIS 14344:2024)
Schweißzusätze - Beschaffung von Schweißzusätzen (ISO/DIS 14344:2024)
Produits consommables pour le soudage - Approvisionnement en matériaux d'apport et
flux (ISO/DIS 14344:2024)
Ta slovenski standard je istoveten z: prEN ISO 14344
ICS:
25.160.20 Potrošni material pri varjenju Welding consumables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14344
ISO/TC 44/SC 3 Secretariat: ANSI
Voting begins on: Voting terminates on:
2024-01-23 2024-04-16
Welding consumables — Procurement of filler materials
and fluxes
Produits consommables pour le soudage — Approvisionnement en matériaux d'apport et flux
ICS: 25.160.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 14344:2024(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2024
ISO/DIS 14344:2024(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 14344
ISO/TC 44/SC 3 Secretariat: ANSI
Voting begins on: Voting terminates on:
Welding consumables — Procurement of filler materials
and fluxes
Produits consommables pour le soudage — Approvisionnement en matériaux d'apport et flux
ICS: 25.160.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2024
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 14344:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 14344:2023(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Lot classification . 4
4.1 General . 4
4.2 Solid welding consumables . 4
4.2.1 Lot Class S1 . 4
4.2.2 Lot Class S2 . . 4
4.2.3 Lot Class S3 . 4
4.2.4 Lot Class S4 . 4
4.2.5 Lot Class S5 . . 4
4.3 Tubular cored electrodes and rods. 5
4.3.1 Lot Class T1 . 5
4.3.2 Lot Class T2 . 5
4.3.3 Lot Class T3 . 5
4.3.4 Lot Class T4 . 5
4.4 Covered electrodes . 5
4.4.1 Lot Class C1 . 5
4.4.2 Lot Class C2 . 6
4.4.3 Lot Class C3 . 6
4.4.4 Lot Class C4 . 6
4.4.5 Lot Class C5 . 6
4.5 Fluxes for electroslag and submerged arc welding . 6
4.5.1 Lot Class F1 . 6
4.5.2 Lot Class F2 . 6
5 Testing schedule . 6
5.1 General . 6
5.2 Schedule 1 or F . 7
5.3 Schedule 2 or G . 7
5.4 Schedule 3 or H . 7
5.5 Schedule 4 or I . 7
5.6 Schedule 5 or J . 8
5.7 Schedule 6 or K . 8
6 Certification . 9
6.1 General . 9
6.2 Certificates . 9
6.2.1 Certificate of Compliance . . 9
6.2.2 Certificate of Conformance . 9
6.2.3 Certified Material Test Report (CMTR) . 9
6.3 Inspection documents. 9
Annex A (informative) Examples of how to apply the 24 h limitation .10
Bibliography .12
iii
ISO/DIS 14344:2023(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 3, Welding consumables.
Any feedback, question or reques
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.