EN ISO 21225-2:2018
(Main)Plastics piping systems for the trenchless replacement of underground pipeline networks - Part 2: Replacement off the line by horizontal directional drilling and impact moling (ISO 21225-2:2018)
Plastics piping systems for the trenchless replacement of underground pipeline networks - Part 2: Replacement off the line by horizontal directional drilling and impact moling (ISO 21225-2:2018)
ISO 21225-2:2018 specifies requirements and test methods for pipes and fittings which are part of plastics piping systems for the trenchless replacement of various underground pipeline networks, underground non-pressure and pressure drainage and sewerage networks and underground water and gas supply networks, by means of horizontal directional drilling and impact moling.
ISO 21225-2:2018 is applicable to polyethylene (PE) pipes and fittings, as manufactured, as well as to the installed replacement system.
ISO 21225-2:2018 is intended to be used in conjunction with standards applicable for the construction of PE pipeline systems where available.
Regarding manufactured pipes it is applicable to three different PE pipe types:
- PE solid wall single layered pipes (nominal outside diameter, dn), including any identification stripes;
- PE pipes with co-extruded layers on either or both the outside and inside of the pipe (total outside diameter, dn), as specified in Annex A, where all layers have the same MRS rating;
- PE pipes (outside diameter, dn) having a peelable, contiguous, thermoplastics additional layer on the outside of the pipe ("coated pipe"), see Annex A.
In addition, ISO 21225-2:2018 is applicable to:
- jointing of pipe lengths by means of butt fusion joint to form continuous strings prior to installation;
- fabricated and injection-moulded fittings made of PE.
Pipes made from other plastics, e.g. polypropylene (PP) are outside the scope of this document.
ISO 21225-2:2018 is not applicable to push-fit jointed discrete pipes assembled as part of the trenchless installation process.
Kunststoff-Rohrleitungssysteme zur grabenlosen Erneuerung von erdverlegten Rohrleitungsnetzen - Teil 2: Erneuerung in anderer Linienführung durch Horizontal-Spülbohrverfahren (HDD) und Bodenverdrängungsverfahren (ISO 21225-2:2018)
Dieses Dokument legt Anforderungen und Prüfverfahren für Rohre und Formstücke fest, die Teil von Kunststoff Rohrleitungssystemen sind und die mithilfe von Horizontal-Spülbohrverfahren (HDD) und Bodenverdrängungsverfahren zur grabenlosen Erneuerung von verschiedenen erdverlegten Rohrleitungs¬netzen, erdverlegten drucklosen Entwässerungsnetzen und Abwasserdruckleitungen und erdverlegten Wasser und Gasversorgungsnetzen verwendet werden.
Es gilt für Polyethylen-(PE )Rohre und Formstücke „wie hergestellt“ sowie für das eingebaute Erneuerungssystem.
Dieses Dokument ist für die Verwendung in Verbindung mit Normen vorgesehen, die für die Konstruktion von PE Rohrleitungssystemen gelten, wenn verfügbar.
Bezüglich hergestellter Rohre gilt es für drei verschiedene PE Rohrarten:
— einschichtige PE Vollwandrohre (Nenn Außendurchmesser dn), einschließlich jeglicher Kenn-zeichnungsstreifen;
— PE Rohre mit koextrudierten Schichten auf entweder der Innen oder Außenseite des Rohrs oder beiden (Gesamt Außendurchmesser dn), wie in Anhang A festgelegt, wobei alle Schichten über die gleiche erforderliche Mindestfestigkeit verfügen;
— PE Rohre (Außendurchmesser dn) mit einer abziehbaren, zusammenhängenden, thermoplastischen Zusatzschicht auf der Rohr Außenseite („beschichtetes Rohr“), siehe Anhang A.
Zusätzlich gilt es für:
— das Verbinden von Rohrlängen durch eine Stumpfschweißverbindung, um vor dem Einbau durchgehende Stränge zu erzeugen;
— vorgefertigte und Spritzguss Formstücke aus PE.
Aus anderen Kunststoffen hergestellte Rohre, z. B. Polypropylen (PP), sind nicht im Anwendungsbereich dieses Dokuments enthalten.
Dieses Dokument gilt nicht für mit Steckmuffen verbundene Einzelrohre, die als Teil des grabenlosen Einbauprozesses zusammengebaut wurden.
Systèmes de canalisations en plastique pour le remplacement sans tranchée des réseaux de canalisations enterrés - Partie 2: Remplacement hors ligne par forage horizontal dirigé et fonçage par fusée (ISO 21225-2:2018)
L'ISO 21225-2:2018 spécifie les exigences et les méthodes d'essai appliqués aux tuyaux et raccords intégrés aux systèmes de canalisations en plastique pour le remplacement sans tranchée de différents réseaux de canalisations enterrés, des réseaux de branchements et de collecteurs d'assainissement enterrés sans pression et sous pression, ainsi que des réseaux d'alimentation en eau et de distribution de gaz enterrés, par forage horizontal dirigé et fonçage par fusée.
L'ISO 21225-2:2018 s'applique aux tuyaux et raccords en polyéthylène (PE), tels que fabriqués, ainsi qu'au système de remplacement, une fois installé.
L'ISO 21225-2:2018 est destiné à être utilisé conjointement avec les normes applicables à la construction de systèmes de canalisations en PE, lorsqu'elles sont disponibles.
Pour ce qui est des tuyaux fabriqués, il s'applique à trois types différents de tuyaux en PE:
- tuyaux en PE monocouches à paroi compacte (diamètre extérieur nominal, dn), y compris les bandes d'identification éventuelles;
- tuyaux en PE avec des couches co-extrudées à l'extérieur et/ou à l'intérieur du tuyau (diamètre extérieur total, dn), tels que spécifiés dans l'Annexe A, toutes les couches ayant la même classification MRS;
- tuyaux en PE (diamètre extérieur, dn) comportant une couche thermoplastique supplémentaire pelable et contiguë à l'extérieur du tuyau («tuyau revêtu»), voir l'Annexe A.
En outre, l'ISO 21225-2:2018 s'applique également:
- l'assemblage des longueurs de tuyau par soudage bout à bout pour former des trains de tuyaux continus avant l'installation;
- les raccords en PE façonnés et moulés par injection.
Les tuyaux fabriqués dans d'autres plastiques, par exemple en polypropylène (PP), en dehors du domaine d'application du présent document.
L'ISO 21225-2:2018 n'est pas applicable aux tuyaux courts à emboîtement instantané assemblés dans le cadre du processus d'installation sans tranchée.
Cevni sistemi iz polimernih materialov za zamenjavo cevovodnih omrežij, ki so položeni v zemljo, brez izkopa - 2. del: Zamenjava linije z usmerjenim vrtanjem (ISO 21225-2:2018)
Ta mednarodni standard določa zahteve in preskusne metode za cevi in fitinge, ki so del plastičnih cevnih sistemov za zamenjavo različnih cevovodnih omrežij, ki so položeni v zemljo, podzemnih omrežij za odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu, ter podzemnih omrežij za oskrbo z vodo in s plinom brez izkopa na podlagi usmerjenega vrtanja ter udarnega kopanja.
Uporablja se za polietilenske (PE) cevi in fitinge, kot so izdelani, ter za nameščeni sistem zamenjave.
Ta standard naj bi se uporabljal v povezavi s standardi za izdelavo cevnih sistemov iz polietilenskih cevi, če so na voljo.
V zvezi z izdelanimi cevmi se uporablja za tri različne vrste polietilenskih cevi:
– PE trdne stenske cevi iz ene plasti (nazivni zunanji premer, dn) s kakršnimi koli identifikacijskimi črtami;
– PE cevi s koekstrudiranimi sloji na zunanji in/ali notranji strani cevi (celotni zunanji premer, dn), kot je opredeljeno v dodatku A, pri čemer imajo vsi sloji enako oceno MRS;
– PE prevlečene cevi (zunanji premer, dn) s termoplastičnim dodatnim slojem, ki ga je mogoče odluščiti, na zunanji strani cevi (»prevlečena cev«), glejte dodatek A.
Poleg tega zajema:
– spajanje dolžin cevi prek soležnega taljenja za oblikovanje neprekinjenega niza pred namestitvijo;
– izdelane in brizgano lite fitinge iz PE.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2018
Cevni sistemi iz polimernih materialov za zamenjavo cevovodnih omrežij, ki so
položeni v zemljo, brez izkopa - 2. del: Zamenjava linije z usmerjenim vrtanjem
(ISO 21225-2:2018)
Plastics piping systems for the trenchless replacement of underground pipeline networks
- Part 2: Replacement off the line by horizontal directional drilling and impact moling (ISO
21225-2:2018)
Kunststoff-Rohrleitungssysteme zur grabenlosen Erneuerung von erdverlegten
Rohrleitungsnetzen - Teil 2: Erneuerung in anderer Linienführung zur Ausführung von
Durchpressungen und Durchbohrungen mit einer horizontalen Bohranlage (ISO 21225-
2:2018)
Systèmes de canalisations en plastique pour le remplacement sans tranchée des
réseaux de canalisations enterrés - Partie 2: Remplacement hors ligne par forage
horizontal dirigé et fonçage par fusée (ISO 21225-2:2018)
Ta slovenski standard je istoveten z: EN ISO 21225-2:2018
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 21225-2
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 91.140.80
English Version
Plastics piping systems for the trenchless replacement of
underground pipeline networks - Part 2: Replacement off
the line by horizontal directional drilling and impact
moling (ISO 21225-2:2018)
Systèmes de canalisations en plastique pour le Kunststoff-Rohrleitungssysteme zur grabenlosen
remplacement sans tranchée des réseaux de Erneuerung von erdverlegten Rohrleitungsnetzen -
canalisations enterrés - Partie 2: Remplacement hors Teil 2: Erneuerung in anderer Linienführung zur
ligne par forage horizontal dirigé et fonçage par fusée Ausführung von Durchpressungen und
(ISO 21225-2:2018) Durchbohrungen mit einer horizontalen Bohranlage
(ISO 21225-2:2018)
This European Standard was approved by CEN on 1 March 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21225-2:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 21225-2:2018) has been prepared by Technical Committee ISO/TC 138
“Plastics pipes, fittings and valves for the transport of fluids” in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by November 2018, and conflicting national standards
shall be withdrawn at the latest by November 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 21225-2:2018 has been approved by CEN as EN ISO 21225-2:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 21225-2
First edition
2018-04
Plastics piping systems for
the trenchless replacement of
underground pipeline networks —
Part 2:
Replacement off the line by horizontal
directional drilling and impact moling
Systèmes de canalisations en plastique pour le remplacement sans
tranchée des réseaux de canalisations enterrés —
Partie 2: Remplacement hors ligne par forage horizontal dirigé et
fonçage par fusée
Reference number
ISO 21225-2:2018(E)
©
ISO 2018
ISO 21225-2:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 21225-2:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 7
4.1 Symbols . 7
4.2 Abbreviated terms . 8
5 Design aspects . 8
6 Material selection . 8
6.1 Pipes and fittings . 8
6.2 Regional requirements for pipes and fittings . 9
6.3 Ancillary components . 9
7 Installation practice . 9
7.1 Preparatory work . 9
7.2 Storage, handling and transport . 9
7.3 Equipment .10
7.3.1 General.10
7.3.2 Inspection equipment .10
7.3.3 Lifting equipment .10
7.3.4 Butt fusion equipment and debeading equipment.10
7.3.5 Pipe skids/rollers .10
7.3.6 HDD equipment .11
7.3.7 Impact moling equipment.11
7.3.8 Electrofusion equipment .12
7.4 Installation .12
7.5 Process-related inspection and testing .13
7.6 Finishing off .13
7.7 Connection to the existing pipeline system.13
8 Fitness for purpose .14
8.1 General .14
8.2 Final inspection .14
8.3 Pressure testing .14
8.4 Disinfection .14
8.5 Documentation .15
Annex A (normative) Layered pipes .16
Annex B (informative) Pipe design considerations particular to HDD .17
Bibliography .19
ISO 21225-2:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committee
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.