EN 12274-3:2002
(Main)Slurry surfacing - Test methods - Part 3: Consistency
Slurry surfacing - Test methods - Part 3: Consistency
This European Standard specifies a test method for determining a consistency of slurry surfacing mixtures.
NOTE 1 The method can be used as a mix design aid to determine the amount of water required to form a stable, workable mixtu-re.
NOTE 2 To obtain the correct consistency, it can be necessary to repeat the test with different known percentages of water.
This European Standard applies to slurry surfacings for roads, airfields and other trafficked areas.
Dünne Asphaltschicht in Kaltbauweise - Prüfverfahren - Teil 3: Konsistenz
Diese Europäische Norm beschreibt ein Prüfverfahren für die Bestimmung der Konsistenz von dünnen
Asphaltschichten in Kaltbauweise.
ANMERKUNG 1 Das Verfahren kann für die Mischungsrezeptur verwendet werden, um die für die Herstellung eines
verarbeitbaren Mischgutes von Bitumenschlämmen benötigte Wassermenge zu bestimmen.
ANMERKUNG 2 Um die Konsistenz genau zu ermitteln, kann die Wiederholung der Prüfung mit unterschiedlichen
Wasseranteilen erforderlich sein.
Diese Norm gilt für dünne Asphaltschichten in Kaltbauweise von Straßen, Flugplätzen und anderen Verkehrs-flächen.
Matériaux bitumineux coulés à froid - Méthodes d'essai - Partie 3: Consistance
La présente Norme européenne spécifie une méthode d'essai pour la détermination de la consistance des mélanges de matériaux bitumineux coulés à froid.
NOTE 1 La méthode peut être utilisée comme aide à la conception des mélanges pour déterminer la quantité d'eau nécessaire à la formation d'un mélange stable, exploitable.
NOTE 2 Pour obtenir la consistance correcte, il peut être nécessaire de répéter l'essai avec différentes proportions d'eau connues.
La présente Norme européenne s'applique aux matériaux bitumineux coulés à froid pour les routes, terrains d'aviation et autres zones de trafic.
Slurry surfacing - Test methods - Part 3: Consistency
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2002
Slurry surfacing - Test methods - Part 3: Consistency
Slurry surfacing - Test methods - Part 3: Consistency
Dünne Asphaltschicht in Kaltbauweise - Prüfverfahren - Teil 3:
Konsistenz
Matériaux bitumineux coulés a froid - Méthodes d'essai - Partie 3: Consistance
Ta slovenski standard je istoveten z: EN 12274-3:2002
ICS:
93.080.20 Materiali za gradnjo cest Road construction materials
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 12274-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2002
ICS 93.080.20
English version
Slurry surfacing - Test methods - Part 3: Consistency
Matériaux bitumineux coulés à froid - Méthodes d'essai - Dünne Asphaltschicht in Kaltbauweise - Prüfverfahren - Teil
Partie 3: Consistance 3: Konsistenz
This European Standard was approved by CEN on 9 November 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2002 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12274-3:2002 E
worldwide for CEN national Members.
Contents
page
Foreword.3
1 Scope .4
2 Apparatus .4
3 Procedure .5
4 Expression of results .6
5 Test report .6
Bibliography .7
Foreword
This European Standard has been prepared by Technical Committee CEN/TC 227 "Road materials", the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or
by endorsement, at the latest by July 2002, and conflicting national standards shall be withdrawn at the latest by
June 2004.
This European Standard is one of a series of standards as listed below:
EN 12274-1, Slurry surfacing Test methods Part 1: Sampling for binder extraction
EN 12274-2, Slurry surfacing Test methods Part 2: Determination of residual binder content
EN 12274-3, Slurry surfacing Test methods Part 3: Consistency
EN 12274-4, Slurry surfacing Test methods Part 4: Determination of cohesion of the mix
EN 12274-5, Slurry surfacing Test methods Part 5: Determination of wearing
EN 12274-6, Slurry surfacing Test methods Part 6:
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.