EN 15611:2008
(Main)Railway applications - Braking - Relay valves
Railway applications - Braking - Relay valves
This European Standard is applicable to relay valves designed to control the brake cylinder pressure of compressed air brakes fitted to railway vehicles, in association with an air brake distributor valve or other control device, and in response to a change in vehicle load that is either continuously variable or in two stages i.e. empty - loaded.
Relay valves operating with other pressures, in particular the brake pipe pressure, are not included.
This European Standard specifies the requirements for the design, manufacture and testing of relay valves.
Bahnanwendungen - Bremse - Relaisventile
Diese Europäische Norm gilt für Relaisventile zur Steuerung des Bremszylinderdruckes von Druckluftbremsen
in Eisenbahnfahrzeugen in Zusammenarbeit mit einem Bremssteuerventil oder einem anderen Steuerelement,
abhängig von einer Veränderung der Fahrzeugbeladung, die entweder autokontinuierlich oder
zweistufig, d. h. „leer“ — „beladen“, erfolgt.
Relaisventile, die mit anderen Betriebsdrücken, insbesondere dem Druck in der Hauptluftleitung, arbeiten,
sind hierin nicht erfasst.
In dieser Europäischen Norm werden die Anforderungen für die Konstruktion, die Herstellung und die Prüfung
von Relaisventilen festgelegt.
Applications ferroviaires - Freinage - Relais pneumatiques
La présente Norme européenne s’applique aux relais pneumatiques conçus pour commander la pression du
cylindre des freins à air comprimé montés sur les véhicules ferroviaires, en association avec un distributeur de
freinage à air ou un autre dispositif de commande et en fonction des variations de la charge du véhicule. La
pression commandée peut varier soit continuellement en fonction des variations de la charge, soit par paliers
à 2 niveaux (un niveau pour l’état de charge « vide » et un autre pour l’état de charge « chargé »).
Les relais pneumatiques fonctionnant avec d’autres pressions, notamment la pression de conduite générale,
ne sont pas considérés dans cette norme.
La présente Norme européenne spécifie les exigences relatives à la conception, à la fabrication et aux essais
des relais pneumatiques.
Železniške naprave - Zavore - Ventili za kontrolo tlaka
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Železniške naprave - Zavore - Ventili za kontrolo tlakaBahnanwendungen - Bremse - RelaisventileRailway applications - Braking - Relay valves45.040Materiali in deli za železniško tehnikoMaterials and components for railway engineeringICS:Ta slovenski standard je istoveten z:EN 15611:2008SIST EN 15611:2009en,fr01-januar-2009SIST EN 15611:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15611November 2008ICS 45.060.01 English VersionRailway applications - Braking - Relay valvesApplications ferroviaires - Freinage - Relais pneumatiquesBahnanwendungen - Bremse - RelaisventileThis European Standard was approved by CEN on 27 September 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15611:2008: ESIST EN 15611:2009
In-service trial.49 A.1 General.49 A.2 Test set-up and sampling.49 A.3 Procedure.49 A.4 Pass/fail criteria.49 Annex B (informative)
Static vehicle and running tests.50 B.1 General.50 B.2 Test recommendations.50 B.2.1 Variable load relay valve.50 B.2.2 Empty/load relay valve.51 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 96/48/EC as modified by Directive 2004/50/EC.52 Annex ZB (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 2001/16/EC of the European Parliament and of the Council of 19 March 2001 on the interoperability of the trans-European conventional rail system, as modified by EU Directive 2004/50/EC of 29 April 2004.53 Bibliography.54
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.