EN ISO 15973:2000

SLOVENSKI STANDARD
SIST EN ISO 15973:2002
01-julij-2002
Slepe polne kovice z zarezanim zakovnim trnom in zaobljeno valjasto glavo (ISO
15973:2000)
Closed end blind rivets with break pull mandrel and protruding head - AIA/St (ISO
15973:2000)
Geschlossene Blindniete mit Sollbruchdorn und Flachkopf -AlA/ St (ISO 15973:2000)
Rivets aveugles a rupture de tige a corps fermé, a tete bombée -AlA/ St (ISO
15973:2000)
Ta slovenski standard je istoveten z: EN ISO 15973:2000
ICS:
21.060.40 Kovice Rivets
SIST EN ISO 15973:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15973:2002

---------------------- Page: 2 ----------------------

SIST EN ISO 15973:2002
EUROPEAN STANDARD
EN ISO 15973
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2000
ICS 21.060.40
English version
Closed end blind rivets with break pull mandrel and protruding
head - AlA/St (ISO 15973:2000)
Rivets aveugles à rupture de tige à corps fermé, à tête Geschlossene Blindniete mit Sollbruchdorn und Flachkopf -
bombée - AlA/St (ISO 15973:2000) AlA/St (ISO 15973:2000)
This European Standard was approved by CEN on 15 December 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15973:2000 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15973:2002
Page 2
EN ISO 15973:2000
Foreword
Corrected 2001-04-04
The text of the International Standard ISO 15973:2000 has been prepared by Technical
Committee ISO/TC 2 "Fasteners" in collaboration with Technical Committee CEN/TC 185
"Threaded and non-threaded mechanical fasteners and accessories", the secretariat of which
is held by DIN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by June 2001, and conflicting national
standards shall be withdrawn at the latest by June 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 15973:2000 was approved by CEN as a European
Standard without any modification.
NOTE: Normative references to International Standards are listed in annex ZA (normative).

---------------------- Page: 4 ----------------------

SIST EN ISO 15973:2002
Page 3
EN ISO 15973:2000
Annex ZA (normative)
Normative references to international publications
with their relevant European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HD applies.
Publication Year Title EN Year
ISO 3269 2000 Fasteners - Acceptance inspection EN ISO 3269 2000
ISO 14588 2000 Blind rivets - Terminology and EN ISO 14588 2000
definitions
ISO 14589 2000 Blind rivets - Mechanical testing EN ISO 14589 2000

---------------------- Page: 5 ----------------------

SIST EN ISO 15973:2002

---------------------- Page: 6 ----------------------

SIST EN ISO 15973:2002
INTERNATIONAL ISO
STANDARD 15973
First edition
2000-12-15
Closed
...