prEN 3162

SLOVENSKI STANDARD
01-september-2024
Aeronavtika - Jeklo X5CrNiCu17-4 (1.4542) - Taljeno - Topilno žarjeno in
izločevalno utrjeno - Pločevina in trakovi - a ≤ 6 mm - Rm ≥ 930 MPa
Aerospace series - Steel X5CrNiCu17-4 (1.4542) - Air melted - Solution treated and
precipitation treated - Sheets and strips - a ≤ 6 mm - Rm ≥ 930 MPa
Luft- und Raumfahrt - Stahl X5CrNiCu17-4 (1.4542) - Lufterschmolzen - Lösungsgeglüht
und ausgehärtet - Bleche und Bänder - a ≤ 6 mm - Rm ≥ 930 MPa
Série aérospatiale - Acier X5CrNiCu17-4 (1.4542) - Élaboré à l'air - Mis en solution et
précipité - Tôles et bandes - a ≤ 6 mm - Rm ≥ 930 MPa
Ta slovenski standard je istoveten z: prEN 3162
ICS:
49.025.10 Jekla Steels
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2024
ICS 49.025.10 Will supersede EN 3162:2007
English Version
Aerospace series - Steel X5CrNiCu17-4 (1.4542) - Air
melted - Solution treated and precipitation treated - Sheets
and strips - a  6 mm - Rm  930 MPa
Série aérospatiale - Acier X5CrNiCu17-4 (1.4542) - Luft- und Raumfahrt - Stahl X5CrNiCu17-4 (1.4542) -
Élaboré à l'air - Mis en solution et précipité - Tôles et Lufterschmolzen - Lösungsgeglüht und ausgehärtet -
bandes - a  6 mm - Rm  930 MPa Bleche und Bänder - a  6 mm - Rm  930 MPa
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 3162:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Introduction . 4
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements . 4
Bibliography . 8

European foreword
This document (prEN 3162:2024) has been prepared by ASD-STAN.
After enquiries and votes carried out in accordance with the rules of this Association, this document has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presen
...