EN ISO 19085-3:2017

SLOVENSKI STANDARD
01-maj-2018
1DGRPHãþD
SIST EN 848-3:2012
/HVQRREGHORYDOQLVWURML9DUQRVWGHO1XPHULþQRNUPLOMHQL1&YUWDOQLLQ
UH]NDOQLVWURML,62
Woodworking machines - Safety requirements - Part 3: Numerically controlled (NC)
boring and routing machines (ISO 19085-3:2017)
Holzbearbeitungsmaschinen - Sicherheit - Teil 3: NC-Bohr- und Fräsmaschinen (ISO
19085-3:2017)
Machines à bois - Sécurité - Partie 3: Perceuses et défonceuses à commande
numérique (ISO 19085-3:2017)
Ta slovenski standard je istoveten z: EN ISO 19085-3:2017
ICS:
25.040.20 âWHYLOþQRNUPLOMHQLVWURML Numerically controlled
machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19085-3
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2017
EUROPÄISCHE NORM
ICS 13.110; 79.120.10 Supersedes EN 848-3:2012
English Version
Woodworking machines - Safety requirements - Part 3:
Numerically controlled (NC) boring and routing machines
(ISO 19085-3:2017)
Machines à bois - Sécurité - Partie 3: Perceuses et Holzbearbeitungsmaschinen - Sicherheit - Teil 3: NC-
défonceuses à commande numérique (CN) (ISO 19085- Bohr- und Fräsmaschinen (ISO 19085-3:2017)
3:2017)
This European Standard was approved by CEN on 9 October 2016.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-3:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC . 4
European foreword
This document (EN ISO 19085-3:2017) has been prepared by Technical Committee ISO/TC 39 “Machine
tools” in collaboration with Technical Committee CEN/TC 142 “Woodworking machines - Safety” the
secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2018, and conflicting national standards shall be
withdrawn at the latest by June 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 848-3:2012.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Serbia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19085-3:2017 has been approved by CEN as EN ISO 19085-3:2017 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC
This European standard has been prepared under a Commission’s standardisation request “M/396” to
provide one voluntary means of conforming to essential requirements of the new approach Machinery
Directive 2006/42.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding essential requirements of that
Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 2006/42/EC
Essential Requirements (ERs) of Directive Clause(s)/sub-clause(s) of this Remarks/Notes
2006/42/EC EN
1.1.2 Principles of safety integration
a) fitted for its function Clauses 5, 6, 7, 8
b) eliminate or reduce the risks, give Clauses 5, 6, 7, 8
measures, inform
c) intended use and reasonably foreseeable Clauses 5, 6, 7, 8
misuse
d) constraints in use 7.5, 8.3
e) equipment 6.1, 8.3
1.1.3 Materials and products 6.2, 7.3
1.1.4 Lighting 7.6, 8.3
1.1.5 Design of machinery to facilitate its 7.5
handling
1.1.6 Ergonomics 7.5
1.1.7 Operating position 5.2
1.2.1 Safety and reliability of control systems 5.1, 5.6, 5.7, 5.8, 5.9, 5.10, 5.11,
5.12, 5.13, 6.5, 6.6, 7.7, 7.8, 7.13
1.2.2 Control devices 5.2, 5.3, 5.4, 5.6, 5.7, 5.13
1.2.3 Starting 5.3, 5.13
1.2.4 Stopping 5.4, 5.5, 5.8, 6.4
1.2.4.1 Normal stop 5.4.2
1.2.4.2 Operational stop 5.4.3
1.2.4.3 Emergency stop 5.4.4
1.2.5 Selection of control or operating mode 5.6
1.2.6 Failure of the power supply 5.8, 7.7, 7.8
1.3.1 Risk of loss of stability 6.1, 8.3
1.3.2 Risk of break-up during operation 6.2, 8.3
1.3.3 Risks due to falling or ejected objects 5.7.3, 6.2, 6.3, 6.5, 6.8, 6.9, 8.3
1.3.4 Risk due to surfaces, edges or angles  Not significant, see
EN ISO 12100:2010
1.3.6 Risks relating to variations in the 5.7, 5.11
operating conditions
1.3.7 Risks related to moving parts 6.5, 6.6, 6.7, 8.3
1.3.8 Choice of protection against risks 6.6, 6.7, 6.8
related to moving parts
1.3.8.1 Moving transmission parts 6.6.3
1.3.8.2 Moving parts involved in the process 6.6.1, 6.6.2, 6.6.4, 6.7
1.3.9 Risk of uncontrolled movements 6.1.1
1.4.1 General requirements 6.9
1.4.2.1 Fixed guards 6.5.1
1.4.2.2 Interlocking movable guards 6.5.2
1.5.1 Electricity supply 7.4, 7.13
1.5.2 Static electricity 7.11
1.5.3 Energy supply other than electricity 7.7, 7.8
1.5.4 Errors of fitting 7.12
1.5.6 Fire 7.1
1.5.8 Noise 7.2
1.5.11 External radiation 7.9
1.5.12 Laser radiation 7.10
1.5.13 Emission of hazardous materials and 7.3
substances
1.6.1 Machinery maintenance 7.14, 8.3
1.6.2 Access to operating position and 7.14, 8.3
servicing points
1.6.3 Isolation of energy sources 7.13, 8.3
1.6.4 Operator intervention 7.14, 8.3
1.6.5 Cleaning of internal parts 7.14, 8.3
1.7.1 Information and warnings on the 7.10, 8.1, 8.2
machinery
1.7.2 Warning devices 8.1
1.7.3 Marking of machinery 8.2
1.7.4 Instructions 8.3
2.3 Machinery for working wood and
analogous materials
a) guiding 6.10
b) ejection 5.7.3, 6.2, 6.3, 6.5, 6.8, 6.9, 8.3
c) brake 5.5, 6.4
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 19085-3
First edition
2017-10
Woodworking machines — Safety
requirements —
Part 3:
Numerically controlled (NC) boring
and routing machines
Machines à bois — Sécurité —
Partie 3: Perceuses et défonceuses à commande numérique (CN)
Reference number
ISO 19085-3:2017(E)
©
ISO 2017
ISO 19085-3:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 19085-3:2017(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 List of significant hazards . 8
5 Safety requirements and measures for controls .10
5.1 Safety and reliability of control systems .10
5.2 Control devices .10
5.2.1 General.10
5.2.2 Hand-held control sets .11
5.3 Start .11
5.4 Safe stops .12
5.4.1 General.12
5.4.2 Normal stop .12
5.4.3 Operational stop .12
5.4.4 Emergency stop .12
5.5 Braking function of tool spindles .12
5.6 Mode selection .12
5.6.1 General.12
5.6.2 Machining mode [MODE 1] .
...