prEN ISO 17699

SLOVENSKI STANDARD
oSIST prEN ISO 17699:2008
01-junij-2008
Obutev - Preskusne metode za podloge in vložke - Odpornost proti vodni pari in
vpijanju (ISO/DIS 17699:2008)
Footwear - Test methods for uppers and lining - Water vapour permeability and
absorption (ISO/DIS 17699:2008)
Chaussures - Méthodes d'essai des tiges et des doublures - Perméabilité à la vapeur
d'eau et absorption de la vapeur d'eau (ISO/DIS 17699:2008)
Ta slovenski standard je istoveten z: prEN ISO 17699
ICS:
61.060 Obuvala Footwear
oSIST prEN ISO 17699:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN ISO 17699
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2008
ICS 61.060 Will supersede EN 13515:2001
English Version
Footwear - Test methods for uppers and lining - Water vapour
permeability and absorption (ISO/DIS 17699:2008)
Chaussures - Méthodes d'essai des tiges et des doublures
- Perméabilité à la vapeur d'eau et absorption de la vapeur
d'eau (ISO/DIS 17699:2008)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 309.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 17699:2008: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN ISO 17699:2008 (E)
Contents Page
Foreword.3

2

---------------------- Page: 3 ----------------------
prEN ISO 17699:2008 (E)
Foreword
This document (prEN ISO 17699:2008) has been prepared by Technical Committee CEN/TC 309 “Footwear”,
the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/TC 216 "Footwear".
This document is currently submitted to the parallel Enquiry.
This document will supersede EN 13515:2001.
3

---------------------- Page: 4 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 17699
ISO/TC 216 Secretariat: AENOR
Voting begins on: Voting terminates on:
2008-04-03 2008-09-03
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Footwear — Test methods for uppers and lining — Water vapour
permeability and absorption
Chaussures — Méthodes d'essai des tiges et des doublures — Perméabilité à la vapeur d'eau et absorption de
la vapeur d'eau
[Revision of first edition (ISO 17699:2003)]
ICS 61.060

ISO/CEN PARALLEL ENQUIRY
This draft International Standard is a draft standard developed within the European Committee for
Standardization (CEN) and processed under the CEN-lead mode of collaboration as defined in the
Vienna Agreement. The document has been transmitted by CEN to ISO for circulation for ISO member
body voting in parallel with CEN enquiry. Comments received from ISO member bodies, including those
from non-CEN members, will be considered by the appropriate CEN technical body. Should this DIS be
accepted, a final draft, established on the basis of comments received, will be submitted to a parallel two-
month FDIS vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
©
International Organization for Standardization, 2008

---------------------- Page: 5 ----------------------
ISO/DIS 17699
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2008 – All rights reserved

---------------------- Page: 6 ----------------------
ISO/DIS 17699
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Apparatus and material.2
4.1 Water vapour permeability test method.2
4.2 Water vapour absorption test method (see Figure 4).3
5 Sampling and conditioning.5
5.1 Water vapour permeability test method.5
5.2 Water vapour absorption test method.6
6 Test method.6
6.1 Water vapour permeability test method.6
6.1.1 Principle.6
6.1.2 Procedure.6
6.2 Water vapour absorption test method.7
6.2.1 Principle.7
6.2.2 Procedure.7
7 Expression of results.8
7.1 Water vapour permeability test method.8
7.2 Water vapour absorption test method.8
8 Test report.9
8.1 Water vapour permeability test method.9
8.2 Water vapour absorption test method.9

© ISO 2008 – All rights reserved iii

---------------------- Page: 7 ----------------------
ISO/DIS 17699
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 17699 was prepared by Technical Committee ISO/TC 216, Footwear, nd by Technical Committee
CEN/TC 309, Footwear in collaboration.
This edition cancels and replaces the first edition (EN 13515:2001), which has been technically revised.

iv © ISO 2008 – All rights reserved

---------------------- Page: 8 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 17699

Footwear — Test methods for uppers and lining — Water vapour
permeability and absorption
1 Scope
This standard specifies two test methods for assessing, respectively, the water vapour permeability and the
water vapour absorption of uppers or complete upper assembly irrespective of the material, in order to assess
the suitability for the end use.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 18454 Footwear - Standard atmospheres for conditioning and testing of footwear and components for
footwear.
ISO 3696, Water for analytical laboratory use - Specification and test methods (ISO 3696:1987).
ISO 17694, Footwear - Test methods for uppers and lining - Flex resistance.
3 Terms and definitions
For the purposes of this European Standard, the following terms and definitions apply.
3.1
water vapour permeability
amount of water vapour a material will transmit through its structure expressed as mass of water transmitted
per area of material per hour
3.2
water vapour absorption
amount of water vapour a material will absorb in a specified time expressed as mass of water per area of
material
3.3
upper
material forming the outer face of the footwear which is attached to the sole assembly and covers the upper
dorsal surface of the foot. In case of boots, this also includes the outer face of the material covering the leg.
Only the materials that are visible are included, no account should be taken of underlying materials
3.4
complete upper assembly
finished upper, fully seamed, joined or laminated as appropiate, comprising the centre material and any
lining(s) together with all components such as interlinings, adhesives, membranes, foams or rein
...