EN 15701:2016

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffe - Ummantelungen aus thermoplastischen Kunststoffen für Dämmstoffe für die Haustechnik und für betriebstechnische Anlagen - Anforderungen und PrüfungenPlastiques - Enveloppes thermoplastiques pour isolants destinés au bâtiment et aux installations industrielles - Exigences et méthodes d'essaiPlastics - Thermoplastic jackets for insulation products for building equipment and industrial installations - Requirements and test methods83.140.99Drugi izdelki iz gume in polimernih materialovOther rubber and plastics productsICS:Ta slovenski standard je istoveten z:EN 15701:2016SIST EN 15701:2017en,fr,de01-januar-2017SIST EN 15701:2017SLOVENSKI
STANDARDSIST EN 15701:20091DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15701
November
t r s x ICS
z uä s v rä { { Supersedes EN
s w y r sã t r r {English Version
Plastics æ Thermoplastic jackets for insulation products for building equipment and industrial installations æ Requirements and test methods Plastiques æ Enveloppes thermoplastiques pour isolants destinés au bâtiment et aux installations industrielles æ Exigences et méthodes d 5essai
Kunststoffe æ Ummantelungen aus thermoplastischen Kunststoffen für Dämmstoffe für die Haustechnik und für betriebstechnische Anlagen æ Anforderungen und Prüfungen This European Standard was approved by CEN on
t r August
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s w y r sã t r s x ESIST EN 15701:2017

Relationship of this European Standard with Regulation (EU) No. 305/2011 . 15 Bibliography . 19
repeatedly into articles by moulding, extrusion or forming [SOURCE: EN ISO 472:2013, 2.1177] 3.8 jackets rigid, semi-rigid, frequently preformed sheet material that provides mechanical and/or environmental protection or a decorative finish to thermal insulation [SOURCE: EN ISO 9229:2007, 2.5.2] 4 Requirements 4.1 Requirements for the material composition of the jackets Thermoplastic materials within the meaning of this standard are homogenous plastics, composite structures (laminates) of different plastics and composite structures of plastics and other materials including primers where the percentage by mass of the plastic film shall be at least 80 %. 4.2 Requirements for vinyl chloride (VC) residual monomer content Only plastic film shall be used that has a VC residual monomer content not exceeding 0,000 1 % by mass. The test shall be carried out according to 5.1.1. 4.3 Technical and mechanical requirements 4.3.1 General With regard to the technical and mechanical requirements, a distinction is made between: a) film in linear applications; b) plastic film or boards as initial materials for mouldings or finished mouldings made from them. 4.3.2 Technical and mechanical requirements for film for linear applications 4.3.2.1 Film thickness The tolerances given in Table 1 relative to the nominal thickness shall be maintained in at least 95 % of all measurements. SIST EN 15701:2017

200 ±10 201 to 400 ±7
400 ±5 The test shall be carried out according to 5.2.1. 4.3.2.2 Tensile-impact strength The tensile-impact strength shall be at least 300 kJ/m2. The test shall be carried out according to 5.2.2. 4.3.2.3 Width The permissible tolerance of the actual width from the nominal width shall be ± 1 mm. The tolerance shall be maintained in at least 95 % of all width measurements. 4.3.2.4 Roll run length For nominal run lengths up to 50 m, the tolerance shall be ± 0,5 m. The tolerance shall be mainta
...