EN ISO 19232-5:2018

SLOVENSKI STANDARD
01-marec-2019
1HSRUXãLWYHQHSUHLVNDYH.DNRYRVWUDGLRJUDIVNHVOLNHGHO'RORþLWHYPRWQRVWL
VOLNHLQRVQRYQHSURVWRUVNHORþOMLYRVWL]XSRUDERGXSOHNVQLKåLþQLKLQGLNDWRUMHY
NDNRYRVWLVOLNH,62
Non-destructive testing - Image quality of radiographs - Part 5: Determination of the
image unsharpness and basic spatial resolution value using duplex wire-type image
quality indicators (ISO 19232-5:2018)
Zerstörungsfreie Prüfung - Bildgüte von Durchstrahlungsaufnahmen - Teil 5:
Bestimmung der Bildunschärfezahl mit Doppeldraht-Typ- Bildgüteprüfkörpern (ISO
19232-5:2018)
Essais non destructifs - Qualité d'image des radiogrammes - Partie 5: Détermination de
l'indice de flou de l'image et de la résolution spatiale de base à l'aide d'indicateurs de
qualité d'image duplex à fils (ISO 19232-5:2018)
Ta slovenski standard je istoveten z: EN ISO 19232-5:2018
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 19232-5
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 19.100 Supersedes EN ISO 19232-5:2013
English Version
Non-destructive testing - Image quality of radiographs -
Part 5: Determination of the image unsharpness and basic
spatial resolution value using duplex wire-type image
quality indicators (ISO 19232-5:2018)
Essais non destructifs - Qualité d'image des Zerstörungsfreie Prüfung - Bildgüte von
radiogrammes - Partie 5: Détermination de l'indice de Durchstrahlungsaufnahmen - Teil 5: Bestimmung der
flou de l'image et de la résolution spatiale de base à Bildunschärfezahl mit Doppeldraht-Typ-
l'aide d'indicateurs de qualité d'image duplex à fils (ISO Bildgüteprüfkörpern (ISO 19232-5:2018)
19232-5:2018)
This European Standard was approved by CEN on 24 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19232-5:2018 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 19232-5:2018) has been prepared by Technical Committee ISO/TC 135 "Non-
destructive testing" in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing”
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall
be withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19232-5:2013.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 19232-5:2018 has been approved by CEN as EN ISO 19232-5:2018 without any
modification.
INTERNATIONAL ISO
STANDARD 19232-5
Third edition
2018-08
Non-destructive testing — Image
quality of radiographs —
Part 5:
Determination of the image
unsharpness and basic spatial
resolution value using duplex wire-
type image quality indicators
Essais non destructifs — Qualité d'image des radiogrammes —
Partie 5: Détermination de l'indice de flou de l'image et de la
résolution spatiale de base à l'aide d'indicateurs de qualité d'image
duplex à fils
Reference number
ISO 19232-5:2018(E)
©
ISO 2018
ISO 19232-5:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

ISO 19232-5:2018(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Specification of duplex wire-type IQI . 3
4.1 Dimensions, manufacture, and marking . 3
4.1.1 Dimensions and material . 3
4.1.2 Manufacture . 4
4.1.3 Marking . 4
4.2 Declaration of conformity. 4
5 Use of duplex wire . 4
5.1 General . 4
5.2 Visual evaluation . 5
5.3 Evaluation of digital images with profile function . 5
5.4 Evaluation of digital images with profile function by interpolation . 5
5.5 Image quality classes . 6
5.6 Application of duplex wire IQI . 6
6 High resolution IQI with increased measurement range . 8
7 Documentation .10
8 Precision and bias .10
Bibliography .11
ISO 19232-5:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 135, Non-destructive testing,
Subcommittee SC 5, Radiation methods.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
This third edition cancels and replaces the second edition (ISO 19232-5:2013), which has been
technically revised. The main changes compared to the previous edition are as follows:
— new high definition duplex IQI;
— extended description of usage;
— extended table with basic spatial resolution and linepairs/mm;
— evaluation of duplex wire-type IQI by visual evaluation and evaluation with profile function in
digital images.
A list of all parts in the ISO 19232 series can be found on the ISO website.
iv © ISO 2018 – All rights reserved

INTERNATIONAL STANDARD ISO 19232-5:2018(E)
Non-destructive testing — Image quality of radiographs —
Part 5:
Determination of the image unsharpness and basic spatial
resolution value using duplex wire-type image quality
indicators
1 Scope
This document specifies a method of determining the total image unsharpness and basic spatial
resolution of radiographs and radioscopic images. The IQI with up to 13 wire pairs can be used
effectively with tube voltages up to 600 kV. The IQI with more than 13 wire pairs can be used effectively
at tube voltages lower than 225 kV. When using source voltages in the megavolt range, it is possible that
the results are not be completely satisfactory.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited
...