Motorcyclists' protective clothing against mechanical impact — Part 3: Motorcyclists' chest protectors - Requirements and test methods

This European Standard specifies the minimum coverage to be provided by motorcyclists’ chest protectors. This European Standard contains the requirements for the performance of the protectors under impact and details of the test methods, requirements for sizing, ergonomic requirements, and requirements for innocuousness, labelling and the provision of information.
Note that this European Standard defines a product which provides limited protection against mechanical impacts and falls to the chest. If the product is only intended to protect against lofted stones (commonly used in Motocross riding) readers are invited to refer to EN 14021:2003 instead.

Motorradfahrer-Schutzkleidung gegen mechanische Belastung - Teil 3: Brustprotektoren für Motorradfahrer - Anforderungen und Prüfverfahren

Diese Europäische Norm legt die Mindestabdeckung fest, die durch Brustprotektoren für Motorradfahrer bereitzustellen sind. Die Norm enthält Anforderungen bezüglich der Leistung des Protektors bei einem Aufprall, Einzelheiten zu den Prüfverfahren sowie Anforderungen an die Größenbestimmung, Ergonomie, Unschädlichkeit, Kennzeichnung und Informationsbereitstellung.
Es ist zu beachten, dass diese Norm ein Produkt festlegt, dass nur einen begrenzten Schutz gegen einen mechanische Aufprall und Stürze auf die Brust bereitstellt. Falls das Produkt nur dafür vorgesehen ist, gegen hochgeschleuderte Steine zu schützen (allgemein verwendet bei Motocross-Fahrten), werden die Leser stattdessen an EN 14021:2003 verwiesen.

Vêtements de protection contre les chocs mécaniques pour motocyclistes - Partie 3 : Protecteurs de poitrine pour motocyclistes - Exigences et méthodes d'essai

Varovalne obleke za motoriste pred mehanskimi vplivi - 3. del: Ščitniki prsnega koša za motoriste - Zahteve in preskusne metode

Ta evropski standard določa najmanjše kritje, ki ga zagotavljajo ščitniki prsnega koša za motoriste. Ta evropski standard vsebuje zahteve glede delovanja ščitnikov v primeru mehanskega vpliva in podrobnosti o preskusnih metodah, zahteve glede velikosti, ergonomike, neškodljivosti, označevanja in zagotavljanja informacij.
Upoštevajte, da ta evropski standard določa izdelek, ki zagotavlja omejeno zaščito prsnega koša pred mehanskimi vplivi in padci. Če je izdelek namenjen zgolj zaščiti pred udarci kamnov (pogosto se uporablja pri vožnji z motorjem), glejte standard EN 14021:2003.

General Information

Status
Published
Publication Date
18-Dec-2018
Withdrawal Date
29-Jun-2019
Current Stage
9060 - Closure of 2 Year Review Enquiry - Review Enquiry
Start Date
03-Jun-2024
Completion Date
03-Jun-2024

Buy Standard

Standard
EN 1621-3:2019
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Motorradfahrer-Schutzkleidung gegen mechanische Belastung - Teil 3: Brustprotektoren für Motorradfahrer - Anforderungen und PrüfverfahrenVêtements de protection contre les chocs mécaniques pour motocyclistes - Partie 3 : Protecteurs de poitrine pour motocyclistes - Exigences et méthodes d'essaiMotorcyclists' protective clothing against mechanical impact - Part 3: Motorcyclists' chest protectors - Requirements and test methods43.140Motorna kolesa in mopediMotorcycles and mopeds13.340.10Varovalna oblekaProtective clothingICS:Ta slovenski standard je istoveten z:EN 1621-3:2018SIST EN 1621-3:2019en,fr,de01-marec-2019SIST EN 1621-3:2019SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1621-3
December
t r s z ICS
s uä u v rä s r English Version
Motorcyclists 5 protective clothing against mechanical impact æ Part
uã Motorcyclists 5 chest protectors æ Requirements and test methods Vêtements de protection contre les chocs mécaniques pour motocyclistes æ Partie
u ã Protecteurs de poitrine pour motocyclistes æ Exigences et méthodes d 5essai
MotorradfahreræSchutzkleidung gegen mechanische Belastung æ Teil
uã Brustprotektoren für Motorradfahrer æ Anforderungen und Prüfverfahren This European Standard was approved by CEN on
s v November
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s x t sæ uã t r s z ESIST EN 1621-3:2019

Impact Points . 12 6.2.4 Divided Chest protectors -
Impact Attenuation Template . 12 6.2.5 Divided Chest protectors -
Impact Distribution Impact Points . 12 6.3 Impact attenuation test . 12 6.3.1 General . 12 6.3.2 Impact sites . 13 6.3.3 Test results . 15 6.4 Impact distribution test . 15 6.4.1 General . 15 6.4.2 Impact Sites . 15 6.4.3 Test Results . 16 6.5 Sample preconditioning . 16 6.5.1 Ambient impact test . 16 6.5.2 Wet impact test . 16 6.5.3 Optional high temperature impact test . 16 6.5.4 Optional low temperature impact test . 16 SIST EN 1621-3:2019
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.