prEN ISO 7519 rev

SLOVENSKI STANDARD
01-oktober-2024
Tehnična dokumentacija proizvodov - Gradbena dokumentacija - Splošna načela
prikazovanja na situacijskih in sestavnih risbah (ISO/FDIS 7519:2024)
Technical product documentation (TPD) - Construction documentation - General
principles of presentation for general arrangement and assembly drawings (ISO/FDIS
7519:2024)
Documentation technique de produits (TPD) - Documentation de construction - Principes
généraux de présentation pour les dessins de disposition générale et d’assemblage
(ISO/FDIS 7519:2024)
Ta slovenski standard je istoveten z: prEN ISO 7519
ICS:
01.100.30 Gradbeni načrti Construction drawings
01.110 Tehnična dokumentacija za Technical product
izdelke documentation
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

FINAL DRAFT
International
Standard
ISO/FDIS 7519
ISO/TC 10/SC 8
Technical product documentation
Secretariat: SN
(TPD) — Construction
Voting begins on:
documentation — General
2024-08-09
principles of presentation for
Voting terminates on:
general arrangement and assembly
2024-11-01
drawings
Documentation technique de produits (TPD) — Documentation
de construction — Principes généraux de présentation pour les
dessins de disposition générale et d’assemblage
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 7519:2024(en) © ISO 2024

FINAL DRAFT
ISO/FDIS 7519:2024(en)
International
Standard
ISO/FDIS 7519
ISO/TC 10/SC 8
Technical product documentation
Secretariat: SN
(TPD) — Construction
Voting begins on:
documentation — General
principles of presentation for
Voting terminates on:
general arrangement and assembly
drawings
Documentation technique de produits (TPD) — Documentation
de construction — Principes généraux de présentation pour les
dessins de disposition générale et d’assemblage
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2024
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 7519:2024(en) © ISO 2024

ii
ISO/FDIS 7519:2024(en)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Construction drawings . . 2
4.1 General principles .2
4.1.1 Standardized and documented approach to communication .2
4.1.2 Conveyance of purposes .2
4.1.3 Dimensional accuracy .2
4.1.4 Use of content from scanned sources .3
4.1.5 Provision and robustness of external references .3
4.2 Types of drawings .3
4.3 Organization of drawing sets .3
4.3.1 Supplementary information of drawings .3
4.3.2 Hierarchy and grouping of drawings .4
4.4 Site plan.4
4.5 Site layout drawing .5
4.6 General arrangement drawings .6
4.7 Assembly drawings .6
4.8 Component drawings .7
4.9 Detail drawings.7
5 General techniques . 7
5.1 General .7
5.2 General representation techniques .7
5.2.1 Simplification .7
5.2.2 Representation types .7
5.3 Simplified representation .8
5.3.1 General .8
5.3.2 Simplified low level representation .8
5.3.3 Simplified medium level representation .8
5.3.4 Simplified high-level representation .8
5.3.5 Simplified detailed representation .9
5.4 Graphical symbols .9
5.4.1 General .9
5.4.2 Graphical symbol types .10
5.4.3 Presentation .10
5.4.4 Consistent understanding .10
5.4.5 Readability .10
5.5 Lines .10
5.5.1 Line types .10
5.5.2 Line width.11
5.5.3 Line use for parts in the cutting plane .11
5.5.4 Line use for parts in front of the cutting plane .11
5.5.5 Line use for parts beyond the cutting plane .11
5.5.6 Line use for indicating function within a simplified representation . 12
5.5.7 Line use for indicating function within a graphical symbol. 12
5.5.8 Other line uses . 12
5.6 Hatching, shading and colour . 13
5.6.1 Purpose . 13
5.6.2 Hatching and scale . 13
5.6.3 Hatching of large area . 13
5.7 Alphanumerical information .14

iii
ISO/FDIS 7519:2024(en)
5.7.1 General .14
5.7.2 Text styles and height .14
5.7.3 Designations .
...